WXR-2533DHP UBI vol_nameのbootlog

UBIのrootfsにおけるvolume名で問題が出たので、とりあえずbootlogをメモ

追記: vol_nameの問題は target/linux/generic/pending-4.9/ の
491-ubi-auto-create-ubiblock-device-for-rootfs.patch
が原因であることが判明 もしかしたら違うかもしれない。ブート時にubiblockを生成するボリューム名を “rootfs” に固定されてしまっている。

Rootfs vol_name=ubi_rootfs (Kernel Panic)

root@OpenWrt:/tmp# ubidetach -p /dev/mtd0
[   55.826606] ubi0: detaching mtd0
[   55.828567] ubi0: mtd0 is detached
root@OpenWrt:/tmp# ubiformat -f openwrt-ipq806x-WXR-2533DHP-squashfs-cksum.ubi /
dev/mtd0
ubiformat: mtd0 (nand), size 67108864 bytes (64.0 MiB), 512 eraseblocks of 131072 bytes (128.0 KiB), min. I/O size 2048 bytes
libscan: scanning eraseblock 511 -- 100 % complete  
ubiformat: 512 eraseblocks have valid erase counter, mean value is 1
ubiformat: flashing eraseblock 54 -- 100 % complete  
ubiformat: formatting eraseblock 511 -- 100 % complete  
root@OpenWrt:/tmp# reboot
root@OpenWrt:/tmp# [   77.228597] br-lan: port 1(eth1.1) entered disabled state
[   77.235681] device eth1.1 left promiscuous mode
[   77.235703] device eth1 left promiscuous mode
[   77.239243] br-lan: port 1(eth1.1) entered disabled state
[   77.249183] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[   81.722418] reboot: Restarting system


BUFFALO WXR-2533DHP U-Boot Ver 1.14 (May 18 2015 - 13:24:36)

CPU:   IPQ8064 clock 1.4 GHz
DRAM:  DDR3 512 MiB clock 533 MHz
NAND:  ECC 4 bits, 256 MiB
SF: Detected W25Q32 with page size 64 KiB, total 4 MiB
MMC:   
In:    serial
Out:   serial
Err:   serial
cdp: get part failed for 0:HLOS
cdp: get part failed for rootfs
Net:   MAC2 addr:74:3:bd:bc:1d:98
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init  done
eth1
Memory Test Start
Pattern: 55555555
Pattern: AAAAAAAA
Pattern: 00000000
Memory Test Pass 

Hit any key to stop autoboot:  0 
(IPQ) # bootipq
MMC Device 0 not found

dmagic1 0 dmagic2 0 
 
MMC Device 0 not found
Device 1: nand1... is now current device
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000004000000 : "mtd=0"
UBI: volume 2 ("ubi_rootfs_data") re-sized from 9 to 450 LEBs
   Image Name:   ARM OpenWrt Linux-4.9.75
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1999904 Bytes = 1.9 MiB
   Load Address: 42208000
   Entry Point:  42208000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
Setting up atags for msm partition: rootfs

device nand0 , # parts = 1
 #: name                size            offset          mask_flags
 0: fs                  0x04000000      0x00000000      0

active partition: nand0,0 - (fs) 0x04000000 @ 0x00000000

defaults:
mtdids  : none
mtdparts: none
Using machid 0x1260 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.75 (musashino205@Taiha.Net) (gcc version 5.5.0 (OpenWrt GCC 5.5.0 r0+6124-05e6096) ) #0 SMP Fri Jan 12 11:38:06 2018
[    0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt:Machine model: Buffalo WXR-2533DHP
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] percpu: Embedded 13 pages/cpu @ddc07000 s20940 r8192 d24116 u53248
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 121920
[    0.000000] Kernel command line: console=ttyMSM0,115200n8 ubi.mtd=0 root=ubi0:ubi_rootfs rootfstype=squashfs
[    0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 481064K/491520K available (3859K kernel code, 246K rwdata, 1236K rodata, 236K init, 242K bss, 10456K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xde800000 - 0xff800000   ( 528 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xde000000   ( 480 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0208000 - 0xc05cd0b0   (3861 kB)
[    0.000000]       .init : 0xc0723000 - 0xc075e000   ( 236 kB)
[    0.000000]       .data : 0xc075e000 - 0xc079b940   ( 247 kB)
[    0.000000]        .bss : 0xc079d000 - 0xc07d9868   ( 243 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[    0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[    0.000022] Switching to timer-based delay loop, resolution 160ns
[    0.000226] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[    0.000247] pid_max: default: 32768 minimum: 301
[    0.000349] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000361] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000956] CPU: Testing write buffer coherency: ok
[    0.001252] Setting up static identity map for 0x42208280 - 0x422082d8
[    0.004593] Brought up 2 CPUs
[    0.004610] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[    0.004620] CPU: All CPU(s) started in SVC mode.
[    0.016309] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[    0.016491] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.016514] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.016594] pinctrl core: initialized pinctrl subsystem
[    0.017871] NET: Registered protocol family 16
[    0.018158] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.041402] cpuidle: using governor ladder
[    0.072419] cpuidle: using governor menu
[    0.125122] msm_bus_fabric_init_driver
[    0.126260] usbcore: registered new interface driver usbfs
[    0.126354] usbcore: registered new interface driver hub
[    0.126437] usbcore: registered new device driver usb
[    0.126504] pps_core: LinuxPPS API ver. 1 registered
[    0.126517] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
[    0.126550] PTP clock support registered
[    0.128561] clocksource: Switched to clocksource dg_timer
[    0.132552] NET: Registered protocol family 2
[    0.133124] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.133170] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.133229] TCP: Hash tables configured (established 4096 bind 4096)
[    0.133284] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.133305] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.133490] NET: Registered protocol family 1
[    0.135070] No memory allocated for crashlog
[    0.135398] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[    0.141542] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.141558] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.148055] io scheduler noop registered
[    0.148073] io scheduler deadline registered (default)
[    0.149603] 1b500000.pci supply vdda not found, using dummy regulator
[    0.149710] 1b500000.pci supply vdda_phy not found, using dummy regulator
[    0.149802] 1b500000.pci supply vdda_refclk not found, using dummy regulator
[    0.150523] OF: PCI: host bridge /soc/pci@1b500000 ranges:
[    0.150564] OF: PCI:    IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[    0.150587] OF: PCI:   MEM 0x08000000..0x0fdfffff -> 0x08000000
[    0.258751] qcom-pcie 1b500000.pci: link up
[    0.260755] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[    0.260777] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.260797] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[    0.260812] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[    0.261342] PCI: bus0: Fast back to back transfers disabled
[    0.263440] PCI: bus1: Fast back to back transfers disabled
[    0.263785] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[    0.263809] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[    0.263937] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.263959] pci 0000:00:00.0:   bridge window [mem 0x08000000-0x081fffff]
[    0.264732] 1b700000.pci supply vdda not found, using dummy regulator
[    0.264834] 1b700000.pci supply vdda_phy not found, using dummy regulator
[    0.264919] 1b700000.pci supply vdda_refclk not found, using dummy regulator
[    0.265637] OF: PCI: host bridge /soc/pci@1b700000 ranges:
[    0.265678] OF: PCI:    IO 0x31e00000..0x31efffff -> 0x31e00000
[    0.265698] OF: PCI:   MEM 0x2e000000..0x31dfffff -> 0x2e000000
[    0.375679] qcom-pcie 1b700000.pci: link up
[    0.377631] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[    0.377649] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.377664] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[    0.378126] PCI: bus0: Fast back to back transfers disabled
[    0.380291] PCI: bus1: Fast back to back transfers disabled
[    0.380766] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[    0.380788] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[    0.380908] pci 0001:00:00.0: PCI bridge to [bus 01]
[    0.380928] pci 0001:00:00.0:   bridge window [mem 0x2e000000-0x2e1fffff]
[    0.383955] L2 @ QSB rate. Forcing new rate.
[    0.384147] L2 @ 384000 KHz
[    0.384319] CPU0 @ 800000 KHz
[    0.384330] CPU1 @ QSB rate. Forcing new rate.
[    0.384452] CPU1 @ 384000 KHz
[    0.387052] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[    0.388492] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0
[    0.390080] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.390954] msm_serial 16340000.serial: msm_serial: detected port #0
[    0.391055] msm_serial 16340000.serial: uartclk = 7372800
[    0.391126] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 167, base_baud = 460800) is a MSM
[    0.391158] msm_serial: console setup on port #0
[    1.099245] console [ttyMSM0] enabled
[    1.103997] msm_serial: driver initialized
[    1.115417] loop: module loaded
[    1.117483] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xaa
[    1.117515] nand: Micron MT29F2G08ABBEAH4
[    1.124069] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.127912] 2 ofpart partitions found on MTD device qcom_nand.0
[    1.135449] Creating 2 MTD partitions on "qcom_nand.0":
[    1.141247] 0x000000000000-0x000004000000 : "rootfs"
[    1.154217] random: fast init done
[    1.309993] mtd: device 0 (rootfs) set to be root filesystem
[    1.311355] mtdsplit: no squashfs found in "rootfs"
[    1.314776] 0x000004000000-0x000008000000 : "rootfs_1"
[    1.497992] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    1.514633] m25p80 spi32766.0: w25q32dw (4096 Kbytes)
[    1.514844] 13 ofpart partitions found on MTD device spi32766.0
[    1.518671] Creating 13 MTD partitions on "spi32766.0":
[    1.524521] 0x000000000000-0x000000010000 : "SBL1"
[    1.531396] 0x000000010000-0x000000030000 : "MIBIB"
[    1.536145] 0x000000030000-0x000000060000 : "SBL2"
[    1.540999] 0x000000060000-0x000000090000 : "SBL3"
[    1.545762] 0x000000090000-0x0000000a0000 : "DDRCONFIG"
[    1.550690] 0x0000000a0000-0x0000000b0000 : "SSD"
[    1.555685] 0x0000000b0000-0x0000000e0000 : "TZ"
[    1.560654] 0x0000000e0000-0x000000100000 : "RPM"
[    1.565144] 0x000000100000-0x000000170000 : "APPSBL"
[    1.569845] 0x000000170000-0x000000180000 : "APPSBLENV"
[    1.574805] 0x000000180000-0x0000001c0000 : "ART"
[    1.579843] 0x0000001c0000-0x0000001d0000 : "BOOTCONFIG"
[    1.584625] 0x0000001d0000-0x000000240000 : "APPSBL_1"
[    1.591445] libphy: GPIO Bitbanged MDIO: probed
[    1.623795] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[    2.578632] libphy: Fixed MDIO Bus: probed
[    2.578673] libphy: mdio_driver_register: qca8k
[    2.584477] stmmac - user ID: 0x10, Synopsys ID: 0x37
[    2.586058]  Ring mode enabled
[    2.591362]  DMA HW capability register supported[    2.594221]  Enhanced/Alternate descriptors
[    2.599936]  Enabled extended descriptors
[    2.602821]  RX Checksum Offload Engine supported
[    2.606986]  COE Type 2
[    2.611740]  TX Checksum insertion supported
[    2.613930]  Wake-Up On Lan supported
[    2.618443]  Enable RX Mitigation via HW Watchdog Timer
[    2.624769] stmmac - user ID: 0x10, Synopsys ID: 0x37
[    2.627041]  Ring mode enabled
[    2.632361]  DMA HW capability register supported[    2.635200]  Enhanced/Alternate descriptors
[    2.640840]  Enabled extended descriptors
[    2.643799]  RX Checksum Offload Engine supported
[    2.647966]  COE Type 2
[    2.652727]  TX Checksum insertion supported
[    2.654910]  Wake-Up On Lan supported
[    2.659506]  Enable RX Mitigation via HW Watchdog Timer
[    2.664854] i2c /dev entries driver
[    2.669275] Calibration not found.
[    2.671502] qcom-tsens 900000.thermal-sensor: tsens calibration failed
[    2.676604] Speed bin: 0
[    2.681566] PVS bin: 1
[    2.686694] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[    2.686803] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[    2.694426] sdhci: Secure Digital Host Controller Interface driver
[    2.700932] sdhci: Copyright(c) Pierre Ossman
[    2.707083] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.714168] NET: Registered protocol family 10
[    2.719759] NET: Registered protocol family 17
[    2.721908] 8021q: 802.1Q VLAN Support v1.8
[    2.726078] Registering SWP/SWPB emulation handler
[    2.747395] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[    2.761085] s1a: Bringing 0uV into 1050000-1050000uV
[    2.761590] s1b: Bringing 0uV into 1050000-1050000uV
[    2.765573] s2a: Bringing 0uV into 800000-800000uV
[    2.770613] s2b: Bringing 0uV into 800000-800000uV
[    2.778755] of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19
[    2.780320] of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:1, -19
[    2.788025] ubi0: attaching mtd0
[    2.990779] random: crng init done
[    3.995533] ubi0: scanning is finished
[    4.017112] ubi0 warning: ubi_eba_init: cannot reserve enough PEBs for bad PEB handling, reserved 5, need 40
[    4.017984] ubi0: attached mtd0 (name "rootfs", size 64 MiB)
[    4.026064] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    4.031684] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    4.038318] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    4.045242] ubi0: good PEBs: 512, bad PEBs: 0, corrupted PEBs: 0
[    4.052025] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    4.058200] ubi0: max/mean erase counter: 10/2, WL threshold: 4096, image sequence number: 44204486
[    4.065298] ubi0: available PEBs: 0, total reserved PEBs: 512, PEBs reserved for bad PEB handling: 5
[    4.074263] hctosys: unable to open rtc devic[    4.088798] VFS: Cannot open root device "ubi0:ubi_rootfs" or unknown-block(31,0): error -2
[    4.088897] Please append a correct "root=" boot option; here are the available partitions:
[    4.095958] 1f00           65536 mtdblock0 [    4.104347]  (driver?)
[    4.109537] 1f01           65536 mtdblock1 [    4.110702]  (driver?)
[    4.115825] 1f02              64 mtdblock2 [    4.117044]  (driver?)
[    4.122168] 1f03             128 mtdblock3 [    4.123388]  (driver?)
[    4.128510] 1f04             192 mtdblock4 [    4.129806]  (driver?)
[    4.134853] 1f05             192 mtdblock5 [    4.136073]  (driver?)
[    4.141197] 1f06              64 mtdblock6 [    4.142418]  (driver?)
[    4.147540] 1f07              64 mtdblock7 [    4.148759]  (driver?)
[    4.153884] 1f08             192 mtdblock8 [    4.155104]  (driver?)
[    4.160227] 1f09             128 mtdblock9 [    4.161447]  (driver?)
[    4.166569] 1f0a             448 mtdblock10 [    4.167790]  (driver?)
[    4.173001] 1f0b              64 mtdblock11 [    4.174221]  (driver?)
[    4.179491] 1f0c             256 mtdblock12 [    4.180652]  (driver?)
[    4.185860] 1f0d              64 mtdblock13 [    4.187080]  (driver?)
[    4.192291] 1f0e             448 mtdblock14 [    4.193511]  (driver?)
[    4.198718] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,0)
[    4.199964] CPU0: stopping
[    4.208198] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.75 #0
[    4.210972] Hardware name: Generic DT based system
[    4.216830] [] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[    4.221675] [] (show_stack) from [] (dump_stack+0x7c/0x9c)
[    4.229568] [] (dump_stack) from [] (handle_IPI+0xcc/0x184)
[    4.236598] [] (handle_IPI) from [] (gic_handle_irq+0x78/0x94)
[    4.243807] [] (gic_handle_irq) from [] (__irq_svc+0x6c/0x90)
[    4.251430] Exception stack(0xc075ff60 to 0xc075ffa8)
[    4.259004] ff60: 00000001 00000000 00000000 c021a420 00000000 c075e000 c0760fe4 00000001
[    4.264041] ff80: c075ba30 00000000 c075ffb8 00000001 00000000 c075ffb0 c020f510 c020f514
[    4.272182] ffa0: 60000013 ffffffff
[    4.280350] [] (__irq_svc) from [] (arch_cpu_idle+0x2c/0x38)
[    4.283653] [] (arch_cpu_idle) from [] (cpu_startup_entry+0xe8/0x198)
[    4.291299] [] (cpu_startup_entry) from [] (start_kernel+0x36c/0x3f0)
[    4.299363] [] (start_kernel) from [] (0x4220807c)
[    4.307505] Rebooting in 1 seconds..

Rootfs vol_name=rootfs (default)(boot成功)

root@OpenWrt:/tmp# ubidetach -p /dev/mtd0
[   55.072915] ubi0: detaching mtd0
[   55.074900] ubi0: mtd0 is detached
root@OpenWrt:/tmp# ubiformat -f openwrt-ipq806x-WXR-2533DHP-squashfs-cksum.ubi /
dev/mtd0
ubiformat: mtd0 (nand), size 67108864 bytes (64.0 MiB), 512 eraseblocks of 131072 bytes (128.0 KiB), min. I/O size 2048 bytes
libscan: scanning eraseblock 511 -- 100 % complete  
ubiformat: 512 eraseblocks have valid erase counter, mean value is 2
ubiformat: flashing eraseblock 54 -- 100 % complete  
ubiformat: formatting eraseblock 511 -- 100 % complete  
root@OpenWrt:/tmp# reboot
root@OpenWrt:/tmp# [   74.907318] br-lan: port 1(eth1.1) entered disabled state
[   74.920907] device eth1.1 left promiscuous mode
[   74.920928] device eth1 left promiscuous mode
[   74.924333] br-lan: port 1(eth1.1) entered disabled state
[   74.934523] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[   79.408938] reboot: Restarting system


BUFFALO WXR-2533DHP U-Boot Ver 1.14 (May 18 2015 - 13:24:36)

CPU:   IPQ8064 clock 1.4 GHz
DRAM:  DDR3 512 MiB clock 533 MHz
NAND:  ECC 4 bits, 256 MiB
SF: Detected W25Q32 with page size 64 KiB, total 4 MiB
MMC:   
In:    serial
Out:   serial
Err:   serial
cdp: get part failed for 0:HLOS
cdp: get part failed for rootfs
Net:   MAC2 addr:74:3:bd:bc:1d:98
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init  done
eth1
Memory Test Start
Pattern: 55555555
Pattern: AAAAAAAA
Pattern: 00000000
Memory Test Pass 

Hit any key to stop autoboot:  0 
(IPQ) # bootipq
MMC Device 0 not found

dmagic1 0 dmagic2 0 
 
MMC Device 0 not found
Device 1: nand1... is now current device
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000004000000 : "mtd=0"
UBI: volume 2 ("rootfs_data") re-sized from 9 to 450 LEBs
   Image Name:   ARM OpenWrt Linux-4.9.75
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1998932 Bytes = 1.9 MiB
   Load Address: 42208000
   Entry Point:  42208000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
Setting up atags for msm partition: rootfs

device nand0 , # parts = 1
 #: name                size            offset          mask_flags
 0: fs                  0x04000000      0x00000000      0

active partition: nand0,0 - (fs) 0x04000000 @ 0x00000000

defaults:
mtdids  : none
mtdparts: none
Using machid 0x1260 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.75 (musashino205@Taiha.Net) (gcc version 5.5.0 (OpenWrt GCC 5.5.0 r0+6122-b893ec4) ) #0 SMP Fri Jan 12 09:42:14 2018
[    0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt:Machine model: Buffalo WXR-2533DHP
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] percpu: Embedded 13 pages/cpu @ddc07000 s20940 r8192 d24116 u53248
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 121920
[    0.000000] Kernel command line: console=ttyMSM0,115200n8 ubi.mtd=0 root=/dev/ubiblock0_1 rootfstype=squashfs
[    0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 481060K/491520K available (3859K kernel code, 246K rwdata, 1236K rodata, 236K init, 242K bss, 10460K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xde800000 - 0xff800000   ( 528 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xde000000   ( 480 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0208000 - 0xc05cd0b0   (3861 kB)
[    0.000000]       .init : 0xc0723000 - 0xc075e000   ( 236 kB)
[    0.000000]       .data : 0xc075e000 - 0xc079b940   ( 247 kB)
[    0.000000]        .bss : 0xc079d000 - 0xc07d9868   ( 243 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[    0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[    0.000022] Switching to timer-based delay loop, resolution 160ns
[    0.000227] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[    0.000248] pid_max: default: 32768 minimum: 301
[    0.000350] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000364] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000961] CPU: Testing write buffer coherency: ok
[    0.001252] Setting up static identity map for 0x42208280 - 0x422082d8
[    0.004588] Brought up 2 CPUs
[    0.004604] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[    0.004614] CPU: All CPU(s) started in SVC mode.
[    0.016287] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[    0.016469] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.016492] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.016572] pinctrl core: initialized pinctrl subsystem
[    0.017849] NET: Registered protocol family 16
[    0.018135] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.041463] cpuidle: using governor ladder
[    0.072479] cpuidle: using governor menu
[    0.125181] msm_bus_fabric_init_driver
[    0.126322] usbcore: registered new interface driver usbfs
[    0.126412] usbcore: registered new interface driver hub
[    0.126499] usbcore: registered new device driver usb
[    0.126566] pps_core: LinuxPPS API ver. 1 registered
[    0.126578] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
[    0.126611] PTP clock support registered
[    0.128569] clocksource: Switched to clocksource dg_timer
[    0.132544] NET: Registered protocol family 2
[    0.133117] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.133162] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.133220] TCP: Hash tables configured (established 4096 bind 4096)
[    0.133276] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.133296] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.133483] NET: Registered protocol family 1
[    0.135066] No memory allocated for crashlog
[    0.135403] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[    0.141556] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.141571] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.148057] io scheduler noop registered
[    0.148075] io scheduler deadline registered (default)
[    0.149609] 1b500000.pci supply vdda not found, using dummy regulator
[    0.149719] 1b500000.pci supply vdda_phy not found, using dummy regulator
[    0.149809] 1b500000.pci supply vdda_refclk not found, using dummy regulator
[    0.150526] OF: PCI: host bridge /soc/pci@1b500000 ranges:
[    0.150566] OF: PCI:    IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[    0.150590] OF: PCI:   MEM 0x08000000..0x0fdfffff -> 0x08000000
[    0.258752] qcom-pcie 1b500000.pci: link up
[    0.260755] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[    0.260777] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.260797] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[    0.260812] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[    0.261332] PCI: bus0: Fast back to back transfers disabled
[    0.263433] PCI: bus1: Fast back to back transfers disabled
[    0.263779] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[    0.263804] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[    0.263933] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.263955] pci 0000:00:00.0:   bridge window [mem 0x08000000-0x081fffff]
[    0.264716] 1b700000.pci supply vdda not found, using dummy regulator
[    0.264819] 1b700000.pci supply vdda_phy not found, using dummy regulator
[    0.264903] 1b700000.pci supply vdda_refclk not found, using dummy regulator
[    0.265616] OF: PCI: host bridge /soc/pci@1b700000 ranges:
[    0.265656] OF: PCI:    IO 0x31e00000..0x31efffff -> 0x31e00000
[    0.265676] OF: PCI:   MEM 0x2e000000..0x31dfffff -> 0x2e000000
[    0.375646] qcom-pcie 1b700000.pci: link up
[    0.377598] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[    0.377616] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.377630] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[    0.378093] PCI: bus0: Fast back to back transfers disabled
[    0.380261] PCI: bus1: Fast back to back transfers disabled
[    0.380737] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[    0.380758] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[    0.380878] pci 0001:00:00.0: PCI bridge to [bus 01]
[    0.380897] pci 0001:00:00.0:   bridge window [mem 0x2e000000-0x2e1fffff]
[    0.383920] L2 @ QSB rate. Forcing new rate.
[    0.384114] L2 @ 384000 KHz
[    0.384286] CPU0 @ 800000 KHz
[    0.384297] CPU1 @ QSB rate. Forcing new rate.
[    0.384419] CPU1 @ 384000 KHz
[    0.387012] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[    0.388447] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0
[    0.390030] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.390908] msm_serial 16340000.serial: msm_serial: detected port #0
[    0.391006] msm_serial 16340000.serial: uartclk = 7372800
[    0.391076] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 167, base_baud = 460800) is a MSM
[    0.391107] msm_serial: console setup on port #0
[    1.099306] console [ttyMSM0] enabled
[    1.104034] msm_serial: driver initialized
[    1.115097] loop: module loaded
[    1.117159] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xaa
[    1.117193] nand: Micron MT29F2G08ABBEAH4
[    1.123755] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.127596] 2 ofpart partitions found on MTD device qcom_nand.0
[    1.135144] Creating 2 MTD partitions on "qcom_nand.0":
[    1.140934] 0x000000000000-0x000004000000 : "rootfs"
[    1.153945] random: fast init done
[    1.310019] mtd: device 0 (rootfs) set to be root filesystem
[    1.311349] mtdsplit: no squashfs found in "rootfs"
[    1.314800] 0x000004000000-0x000008000000 : "rootfs_1"
[    1.498336] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    1.515164] m25p80 spi32766.0: w25q32dw (4096 Kbytes)
[    1.515383] 13 ofpart partitions found on MTD device spi32766.0
[    1.519324] Creating 13 MTD partitions on "spi32766.0":
[    1.524939] 0x000000000000-0x000000010000 : "SBL1"
[    1.532049] 0x000000010000-0x000000030000 : "MIBIB"
[    1.536585] 0x000000030000-0x000000060000 : "SBL2"
[    1.541434] 0x000000060000-0x000000090000 : "SBL3"
[    1.546286] 0x000000090000-0x0000000a0000 : "DDRCONFIG"
[    1.551112] 0x0000000a0000-0x0000000b0000 : "SSD"
[    1.556291] 0x0000000b0000-0x0000000e0000 : "TZ"
[    1.561156] 0x0000000e0000-0x000000100000 : "RPM"
[    1.565681] 0x000000100000-0x000000170000 : "APPSBL"
[    1.570393] 0x000000170000-0x000000180000 : "APPSBLENV"
[    1.575330] 0x000000180000-0x0000001c0000 : "ART"
[    1.580447] 0x0000001c0000-0x0000001d0000 : "BOOTCONFIG"
[    1.585184] 0x0000001d0000-0x000000240000 : "APPSBL_1"
[    1.591967] libphy: GPIO Bitbanged MDIO: probed
[    1.624437] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[    2.579671] libphy: Fixed MDIO Bus: probed
[    2.579713] libphy: mdio_driver_register: qca8k
[    2.585412] stmmac - user ID: 0x10, Synopsys ID: 0x37
[    2.587094]  Ring mode enabled
[    2.592422]  DMA HW capability register supported[    2.595256]  Enhanced/Alternate descriptors
[    2.600894]  Enabled extended descriptors
[    2.603852]  RX Checksum Offload Engine supported
[    2.608019]  COE Type 2
[    2.612770]  TX Checksum insertion supported
[    2.614965]  Wake-Up On Lan supported
[    2.619552]  Enable RX Mitigation via HW Watchdog Timer
[    2.625698] stmmac - user ID: 0x10, Synopsys ID: 0x37
[    2.628075]  Ring mode enabled
[    2.633388]  DMA HW capability register supported[    2.636234]  Enhanced/Alternate descriptors
[    2.641875]  Enabled extended descriptors
[    2.644834]  RX Checksum Offload Engine supported
[    2.649075]  COE Type 2
[    2.653683]  TX Checksum insertion supported
[    2.655944]  Wake-Up On Lan supported
[    2.660536]  Enable RX Mitigation via HW Watchdog Timer
[    2.665898] i2c /dev entries driver
[    2.670345] Calibration not found.
[    2.672536] qcom-tsens 900000.thermal-sensor: tsens calibration failed
[    2.677603] Speed bin: 0
[    2.682597] PVS bin: 1
[    2.687728] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[    2.687837] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[    2.695473] sdhci: Secure Digital Host Controller Interface driver
[    2.701962] sdhci: Copyright(c) Pierre Ossman
[    2.708118] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.715220] NET: Registered protocol family 10
[    2.720762] NET: Registered protocol family 17
[    2.722953] 8021q: 802.1Q VLAN Support v1.8
[    2.727115] Registering SWP/SWPB emulation handler
[    2.748413] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[    2.762120] s1a: Bringing 0uV into 1050000-1050000uV
[    2.762604] s1b: Bringing 0uV into 1050000-1050000uV
[    2.766607] s2a: Bringing 0uV into 800000-800000uV
[    2.771673] s2b: Bringing 0uV into 800000-800000uV
[    2.779883] of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19
[    2.781274] of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:1, -19
[    2.789168] ubi0: attaching mtd0
[    2.981561] random: crng init done
[    3.991420] ubi0: scanning is finished
[    4.013032] ubi0 warning: ubi_eba_init: cannot reserve enough PEBs for bad PEB handling, reserved 5, need 40
[    4.013923] ubi0: attached mtd0 (name "rootfs", size 64 MiB)
[    4.021971] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    4.027557] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    4.034306] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    4.041149] ubi0: good PEBs: 512, bad PEBs: 0, corrupted PEBs: 0
[    4.047868] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    4.054177] ubi0: max/mean erase counter: 12/3, WL threshold: 4096, image sequence number: 1230543660
[    4.061213] ubi0: available PEBs: 0, total reserved PEBs: 512, PEBs reserved for bad PEB handling: 5
[    4.071596] ubi0: background thread "ubi_bgt0d" started, PID 83
[    4.080138] block ubiblock0_1: created from ubi0:1(ro[    4.097770] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    4.098020] Freeing unused kernel memory: 236K
[    4.103950] This architecture does not have kernel memory protection.
[    4.788137] init: Console is alive
[    4.788472] init: - watchdog -
[    5.792308] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.872724] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.874673] SCSI subsystem initialized
[    5.883347] ehci-platform: EHCI generic platform driver
[    5.885801] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    5.887773] ohci-platform: OHCI generic platform driver
[    6.021738] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    6.021837] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    6.026423] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x02010010
[    6.033881] xhci-hcd xhci-hcd.0.auto: irq 169, io mem 0x11000000
[    6.043921] hub 1-0:1.0: USB hub found
[    6.048704] hub 1-0:1.0: 1 port detected
[    6.052879] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    6.056281] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    6.061941] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    6.070478] hub 2-0:1.0: USB hub found
[    6.077515] hub 2-0:1.0: 1 port detected
[    6.081857] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    6.085114] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[    6.090806] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x02010010
[    6.098011] xhci-hcd xhci-hcd.1.auto: irq 170, io mem 0x10000000
[    6.108098] hub 3-0:1.0: USB hub found
[    6.113168] hub 3-0:1.0: 1 port detected
[    6.116593] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    6.120556] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[    6.125853] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    6.133799] hub 4-0:1.0: USB hub found
[    6.141755] hub 4-0:1.0: 1 port detected
[    6.148089] usbcore: registered new interface driver usb-storage
[    6.150009] usbcore: registered new interface driver uas
[    6.155342] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    6.169079] init: - preinit -
[    8.340466] dwmac1000: Master AXI performs any burst length
[    8.340506] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[    8.344948] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[    8.354071] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.370137] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[    9.370584] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   12.684729] mount_root: loading kmods from internal overlay
[   12.706633] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   12.709214] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   13.946318] UBIFS (ubi0:2): default file-system created
[   13.950747] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 172
[   14.178657] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[   14.178796] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   14.185577] UBIFS (ubi0:2): FS size: 55869440 bytes (53 MiB, 440 LEBs), journal size 2793472 bytes (2 MiB, 22 LEBs)
[   14.195561] UBIFS (ubi0:2): reserved for root: 2638851 bytes (2577 KiB)
[   14.205786] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID 5A321190-901A-43BC-804D-EECDEA3A6B83, small LPT model
[   14.214828] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   14.223965] block: unable to load configuration (fstab: Entry not found)
[   14.230685] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[   14.237624] block: unable to load configuration (fstab: Entry not found)
[   14.243980] block: attempting to load /etc/config/fstab
[   14.252937] block: unable to load configuration (fstab: Entry not found)
[   14.255566] block: no usable configuration
[   14.314545] UBIFS (ubi0:2): un-mount UBI device 0
[   14.317139] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" stops
[   14.323832] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 173
[   14.521179] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[   14.521227] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   14.528009] UBIFS (ubi0:2): FS size: 55869440 bytes (53 MiB, 440 LEBs), journal size 2793472 bytes (2 MiB, 22 LEBs)
[   14.537995] UBIFS (ubi0:2): reserved for root: 2638851 bytes (2577 KiB)
[   14.548220] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID 5A321190-901A-43BC-804D-EECDEA3A6B83, small LPT model
[   15.912121] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   15.912356] block: unable to load configuration (fstab: Entry not found)
[   15.918018] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[   15.925305] block: unable to load configuration (fstab: Entry not found)
[   15.931387] block: attempting to load /etc/config/fstab
[   15.938068] block: unable to load configuration (fstab: Entry not found)
[   15.943123] block: no usable configuration
[   16.001666] mount_root: overlay filesystem has not been fully initialized yet
[   16.002789] mount_root: switching to ubifs overlay
[   16.035054] urandom-seed: Seed file not found (/etc/urandom.seed)
[   16.163562] procd: - early -
[   16.163641] procd: - watchdog -
[   16.843570] procd: - watchdog -
[   16.843970] procd: - ubus -
[   17.034687] procd: - init -
Please press Enter to activate this console.
[   17.316120] kmodloader: loading kernel modules from /etc/modules.d/*
[   17.320732] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   17.326596] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[   17.326832] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[   17.336004] ip_tables: (C) 2000-2006 Netfilter Core Team
[   17.344447] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[   17.366908] usbcore: registered new interface driver ums-alauda
[   17.367452] usbcore: registered new interface driver ums-cypress
[   17.372269] usbcore: registered new interface driver ums-datafab
[   17.378358] usbcore: registered new interface driver ums-freecom
[   17.384493] usbcore: registered new interface driver ums-isd200
[   17.390536] usbcore: registered new interface driver ums-jumpshot
[   17.396007] usbcore: registered new interface driver ums-karma
[   17.402510] usbcore: registered new interface driver ums-sddr09
[   17.408027] usbcore: registered new interface driver ums-sddr55
[   17.413986] usbcore: registered new interface driver ums-usbat
[   17.423983] xt_time: kernel timezone is -0000
[   17.439718] PPP generic driver version 2.4.2
[   17.440282] NET: Registered protocol family 24
[   17.448415] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[   17.449053] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   17.621102] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[   17.621132] ath10k_pci 0000:01:00.0: Falling back to user helper
[   18.945606] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
[   18.945645] ath10k_pci 0000:01:00.0: Falling back to user helper
[   18.976661] firmware ath10k!QCA99X0!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[   19.418960] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[   19.419019] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   19.433102] ath10k_pci 0000:01:00.0: firmware ver 10.4.1.00030-1 api 5 features no-p2p crc32 d2901e01
[   19.492058] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2
[   20.757778] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1
[   20.848208] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[   20.849018] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   21.032926] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2
[   21.032969] ath10k_pci 0001:01:00.0: Falling back to user helper
[   22.317558] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
[   22.317590] ath10k_pci 0001:01:00.0: Falling back to user helper
[   22.344229] firmware ath10k!QCA99X0!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[   22.344368] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[   22.352145] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   22.364019] ath10k_pci 0001:01:00.0: firmware ver 10.4.1.00030-1 api 5 features no-p2p crc32 d2901e01
[   22.425771] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:2 crc32 08fa09f2
[   23.746113] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1
[   23.846302] kmodloader: done loading kernel modules from /etc/modules.d/*
[   28.943114] dwmac1000: Master AXI performs any burst length
[   28.943161] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[   28.947605] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[   28.956676] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   28.967962] br-lan: port 1(eth1.1) entered blocking state
[   28.969376] br-lan: port 1(eth1.1) entered disabled state
[   28.974947] device eth1.1 entered promiscuous mode
[   28.980196] device eth1 entered promiscuous mode
[   28.988215] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   29.015558] dwmac1000: Master AXI performs any burst length
[   29.015601] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   29.020168] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[   29.029197] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   29.041070] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   30.008978] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[   30.009864] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   30.018617] br-lan: port 1(eth1.1) entered blocking state
[   30.022990] br-lan: port 1(eth1.1) entered forwarding state
[   30.034736] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   30.089211] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   30.089259] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   30.097543] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
広告

コメントを残す

以下に詳細を記入するか、アイコンをクリックしてログインしてください。

WordPress.com ロゴ

WordPress.com アカウントを使ってコメントしています。 ログアウト /  変更 )

Google フォト

Google アカウントを使ってコメントしています。 ログアウト /  変更 )

Twitter 画像

Twitter アカウントを使ってコメントしています。 ログアウト /  変更 )

Facebook の写真

Facebook アカウントを使ってコメントしています。 ログアウト /  変更 )

%s と連携中