WXR-2533DHP stock -> OpenWrt (2)

以前のstock -> OpenWrt化の記事を書いた時点から、内部的な挙動を変更したのでメモ。

WXR-2533DHPのデフォルトパッケージとして squashfs-tools-mksquashfs を持たせて mksquashfs コマンドを使用できるようにし、WXR-2533DHPのブートに必要なダミーのUBIボリュームをsysupgrade時に作成するようにした。
これにより、factoryを投入後UBIのイメージを使用して sysupgrade -F する必要が無くなり、squashfs-sysupgrade イメージでsysupgradeするのみで良くなった。

Bootlog

stock → OpenWrt (initramfs) → OpenWrt (squashfs)
ハイライトは入力個所

Killed
Monitor.sh starting.......
Start of fw_blink_cnt.sh -------------------------------------------------
End of fw_blink_cnt.sh -------------------------------------------------
do ubi firmware upgrade ...
[  416.083692] UBI: attaching mtd1 to ubi1
[  416.086504] UBI: physical eraseblock size:   131072 bytes (128 KiB)
[  416.093095] UBI: logical eraseblock size:    126976 bytes
[  416.098125] UBI: smallest flash I/O unit:    2048
[  416.103124] UBI: VID header offset:          2048 (aligned 2048)
[  416.108809] UBI: data offset:                4096
[  416.668822] UBI: empty MTD device detected
[  416.672133] UBI: max. sequence number:       0
[  416.676382] UBI: create volume table (copy #1)
[  416.693252] UBI: create volume table (copy #2)
[  416.710059] UBI: attached mtd1 to ubi1
[  416.712808] UBI: MTD device name:            "rootfs_1"
[  416.717994] UBI: MTD device size:            64 MiB
[  416.723149] UBI: number of good PEBs:        512
[  416.727460] UBI: number of bad PEBs:         0
[  416.732083] UBI: number of corrupted PEBs:   0
[  416.736301] UBI: max. allowed volumes:       128
[  416.741080] UBI: wear-leveling threshold:    4096
[  416.745610] UBI: number of internal volumes: 1
[  416.750265] UBI: number of user volumes:     0
[  416.754545] UBI: available PEBs:             503
[  416.759044] UBI: total number of reserved PEBs: 9
[  416.764011] UBI: number of PEBs reserved for bad PEB handling: 5
[  416.769853] UBI: max/mean erase counter: 0/0
[  416.774039] UBI: image sequence number:  1171577802
[  416.778881] UBI: background thread "ubi_bgt1d" started, PID 7267
ubiupdatevol /dev/ubi1_0 /tmp/uhttp-upgrade.img -o 128 -s 4819470
ubiupdatevol /dev/ubi1_1 /tmp/uhttp-upgrade.img -o 4819598 -s 158
$Shutting down pppd: 
disable_ipv4_dns
IPv6_dns = nameserver 240b:12:500:6500:225:36ff:fe14:e98c
reload_servers_safe
######policy stop
Stop DS-Lite Tunnel ...
Stop DS-Lite Tunnel done...
Stop MAP E ...
Stop DS-Lite Tunnel ...
Stop DS-Lite Tunnel done...
Stop MAP E ...
Stop RADVD ...
ip -6 addr delet 240b:12:500:6500:7603:bdff:febc:1d99/64 dev eth0
TMP_WAN_IPV6= 
[  447.302061] Restarting system.
[  447.304092] Going down for restart now


BUFFALO WXR-2533DHP U-Boot Ver 1.14 (May 18 2015 - 13:24:36)

CPU:   IPQ8064 clock 1.4 GHz
DRAM:  DDR3 512 MiB clock 533 MHz
NAND:  ECC 4 bits, 256 MiB
SF: Detected W25Q32 with page size 64 KiB, total 4 MiB
MMC:   
In:    serial
Out:   serial
Err:   serial
cdp: get part failed for 0:HLOS
cdp: get part failed for rootfs
Net:   MAC2 addr:74:3:bd:bc:1d:98
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init  done
eth1
Memory Test Start
Pattern: 55555555
Pattern: AAAAAAAA
Pattern: 00000000
Memory Test Pass 

Hit any key to stop autoboot:  0 
Checking Bank1 Image ... 
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000004000000 : "mtd=0"
Bank1 Image is good
kernel_checksum is 0x4d51f25f , rootfs_checksum is 0xd3 
Checking Bank2 Image ... 
Creating 1 MTD partitions on "nand0":
0x000004000000-0x000008000000 : "mtd=0"
Bank2 Image is good
kernel_checksum is 0x4acf4726 , rootfs_checksum is 0xc9 
Bank1 Image not the same as Bank2 Image 
Cpoy to Bank1 image from Bank2 image 
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000004000000 : "mtd=0"
4819470 bytes written to volume kernel
158 bytes written to volume ubi_rootfs
MMC Device 0 not found

dmagic1 0 dmagic2 0 
 
MMC Device 0 not found
Using nand device 1
Device 1: nand1... is now current device
bootargs=console=ttyHSL1,115200n8 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs
Booting from flash
set mtdids nand0=nand0 && set mtdparts mtdparts=nand0:0x4000000@0x0(fs),${msmparts} && ubi part fs && ubi read 0x44000000 kernel && bootm 0x44000000
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000004000000 : "mtd=0"
   Image Name:   ARM OpenWrt Linux-4.14.89
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4819406 Bytes = 4.6 MiB
   Load Address: 42208000
   Entry Point:  42208000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
Setting up atags for msm partition: rootfs

device nand0 , # parts = 1
 #: name                size            offset          mask_flags
 0: fs                  0x04000000      0x00000000      0

active partition: nand0,0 - (fs) 0x04000000 @ 0x00000000

defaults:
mtdids  : none
mtdparts: none
Using machid 0x1260 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.89 (jenkins@tofu-z77hvub18_openwrt) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r0+8849-8f8ac4c3dc)) #0 SMP Thu Dec 20 13:01:38 2018
[    0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: Buffalo WXR-2533DHP
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] random: get_random_bytes called from start_kernel+0x88/0x408 with crng_init=0
[    0.000000] percpu: Embedded 15 pages/cpu @ddc01000 s29324 r8192 d23924 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 121920
[    0.000000] Kernel command line: 
[    0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 472264K/491520K available (4745K kernel code, 152K rwdata, 1260K rodata, 8192K init, 228K bss, 19256K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xde800000 - 0xff800000   ( 528 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xde000000   ( 480 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0208000 - 0xc07a25f8   (5738 kB)
[    0.000000]       .init : 0xc0900000 - 0xc1100000   (8192 kB)
[    0.000000]       .data : 0xc1100000 - 0xc11261c0   ( 153 kB)
[    0.000000]        .bss : 0xc1128000 - 0xc11610d8   ( 229 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[    0.000006] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[    0.000020] Switching to timer-based delay loop, resolution 160ns
[    0.000233] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[    0.000258] pid_max: default: 32768 minimum: 301
[    0.000381] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000397] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000981] CPU: Testing write buffer coherency: ok
[    0.001752] Setting up static identity map for 0x42300000 - 0x42300060
[    0.001912] Hierarchical SRCU implementation.
[    0.002650] smp: Bringing up secondary CPUs ...
[    0.004459] smp: Brought up 1 node, 2 CPUs
[    0.004478] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[    0.004491] CPU: All CPU(s) started in SVC mode.
[    0.014986] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[    0.015147] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.015173] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.015284] pinctrl core: initialized pinctrl subsystem
[    0.016308] NET: Registered protocol family 16
[    0.016556] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.017914] cpuidle: using governor ladder
[    0.017980] cpuidle: using governor menu
[    0.039275] msm_bus_fabric_init_driver
[    0.040686] usbcore: registered new interface driver usbfs
[    0.040777] usbcore: registered new interface driver hub
[    0.040867] usbcore: registered new device driver usb
[    0.040929] pps_core: LinuxPPS API ver. 1 registered
[    0.040941] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
[    0.040972] PTP clock support registered
[    0.042787] clocksource: Switched to clocksource dg_timer
[    0.046101] NET: Registered protocol family 2
[    0.046616] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.046660] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.046713] TCP: Hash tables configured (established 4096 bind 4096)
[    0.046805] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.046835] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.047035] NET: Registered protocol family 1
[    0.187062] No memory allocated for crashlog
[    0.187376] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[    0.192028] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.192043] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.198948] io scheduler noop registered
[    0.198967] io scheduler deadline registered (default)
[    0.200358] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
[    0.200465] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
[    0.200562] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
[    0.201344] OF: PCI: host bridge /soc/pci@1b500000 ranges:
[    0.201388] OF: PCI:    IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[    0.201413] OF: PCI:   MEM 0x08000000..0x0fdfffff -> 0x08000000
[    0.309447] qcom-pcie 1b500000.pci: link up
[    0.309631] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[    0.309655] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.309674] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[    0.309689] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[    0.310219] PCI: bus0: Fast back to back transfers disabled
[    0.312458] PCI: bus1: Fast back to back transfers disabled
[    0.312557] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[    0.312581] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[    0.312711] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    0.312736] pci 0000:00:00.0:   bridge window [mem 0x08000000-0x081fffff]
[    0.313417] pcieport 0000:00:00.0: AER enabled with IRQ 34
[    0.313991] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
[    0.314095] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
[    0.314199] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
[    0.314953] OF: PCI: host bridge /soc/pci@1b700000 ranges:
[    0.314994] OF: PCI:    IO 0x31e00000..0x31efffff -> 0x31e00000
[    0.315017] OF: PCI:   MEM 0x2e000000..0x31dfffff -> 0x2e000000
[    0.424937] qcom-pcie 1b700000.pci: link up
[    0.425090] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[    0.425109] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.425124] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[    0.425579] PCI: bus0: Fast back to back transfers disabled
[    0.427926] PCI: bus1: Fast back to back transfers disabled
[    0.428011] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[    0.428033] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[    0.428164] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[    0.428184] pci 0001:00:00.0:   bridge window [mem 0x2e000000-0x2e1fffff]
[    0.428672] pcieport 0001:00:00.0: AER enabled with IRQ 67
[    0.430956] L2 @ QSB rate. Forcing new rate.
[    0.431159] L2 @ 384000 KHz
[    0.431329] CPU0 @ 800000 KHz
[    0.431343] CPU1 @ QSB rate. Forcing new rate.
[    0.431461] CPU1 @ 384000 KHz
[    0.435536] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[    0.436941] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0
[    0.438421] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.439246] msm_serial 16340000.serial: msm_serial: detected port #0
[    0.439344] msm_serial 16340000.serial: uartclk = 7372800
[    0.439423] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 100, base_baud = 460800) is a MSM
[    0.439460] msm_serial: console setup on port #0
[    1.172231] console [ttyMSM0] enabled
[    1.177094] msm_serial: driver initialized
[    1.185782] loop: module loaded
[    1.187920] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xaa
[    1.187957] nand: Micron MT29F2G08ABBEAH4
[    1.194439] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.198290] 2 fixed-partitions partitions found on MTD device qcom_nand.0
[    1.205774] Creating 2 MTD partitions on "qcom_nand.0":
[    1.212567] 0x000000000000-0x000004000000 : "ubi"
[    1.225487] random: fast init done
[    1.392922] 0x000004000000-0x000008000000 : "rootfs_1"
[    1.569415] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    1.584327] m25p80 spi0.0: w25q32dw (4096 Kbytes)
[    1.584484] 13 fixed-partitions partitions found on MTD device spi0.0
[    1.588013] Creating 13 MTD partitions on "spi0.0":
[    1.594534] 0x000000000000-0x000000010000 : "SBL1"
[    1.599973] 0x000000010000-0x000000030000 : "MIBIB"
[    1.604812] 0x000000030000-0x000000060000 : "SBL2"
[    1.609504] 0x000000060000-0x000000090000 : "SBL3"
[    1.614492] 0x000000090000-0x0000000a0000 : "DDRCONFIG"
[    1.619144] 0x0000000a0000-0x0000000b0000 : "SSD"
[    1.624328] 0x0000000b0000-0x0000000e0000 : "TZ"
[    1.629113] 0x0000000e0000-0x000000100000 : "RPM"
[    1.633933] 0x000000100000-0x000000170000 : "APPSBL"
[    1.638405] 0x000000170000-0x000000180000 : "APPSBLENV"
[    1.643537] 0x000000180000-0x0000001c0000 : "ART"
[    1.648408] 0x0000001c0000-0x0000001d0000 : "BOOTCONFIG"
[    1.653341] 0x0000001d0000-0x000000240000 : "APPSBL_1"
[    1.659584] libphy: GPIO Bitbanged MDIO: probed
[    1.704291] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[    2.564122] ar8327: qca,phy-rgmii-en is not specified
[    2.564543] libphy: Fixed MDIO Bus: probed
[    2.588350] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[    2.588708] stmmac - user ID: 0x10, Synopsys ID: 0x37
[    2.593890] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[    2.598812] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[    2.604960] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[    2.612873] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[    2.620515] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[    2.627544] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[    2.635414] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[    2.641173] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[    2.648633] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    2.676057] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[    2.676305] stmmac - user ID: 0x10, Synopsys ID: 0x37
[    2.681486] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[    2.686596] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[    2.692597] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[    2.700643] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[    2.708206] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[    2.715232] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[    2.723142] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[    2.728880] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[    2.736323] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    2.743794] i2c /dev entries driver
[    2.752462] Calibration not found.
[    2.754913] qcom-tsens 900000.thermal-sensor: tsens calibration failed
[    2.759430] Speed bin: 0
[    2.764883] PVS bin: 1
[    2.768865] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[    2.769743] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[    2.777474] sdhci: Secure Digital Host Controller Interface driver
[    2.784238] sdhci: Copyright(c) Pierre Ossman
[    2.790419] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.796529] NET: Registered protocol family 10
[    2.801830] Segment Routing with IPv6
[    2.805015] NET: Registered protocol family 17
[    2.809219] 8021q: 802.1Q VLAN Support v1.8
[    2.812936] Registering SWP/SWPB emulation handler
[    2.829454] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[    2.844830] s1a: supplied by regulator-dummy
[    2.844916] s1a: Bringing 0uV into 1050000-1050000uV
[    2.848468] s1b: supplied by regulator-dummy
[    2.853240] s1b: Bringing 0uV into 1050000-1050000uV
[    2.857613] s2a: supplied by regulator-dummy
[    2.862367] s2a: Bringing 0uV into 800000-800000uV
[    2.866890] s2b: supplied by regulator-dummy
[    2.871231] s2b: Bringing 0uV into 800000-800000uV
[    2.881060] UBI: auto-attach mtd0
[    2.881095] ubi0: attaching mtd0
[    2.977065] random: crng init done
[    3.911204] ubi0: scanning is finished
[    3.931436] ubi0: attached mtd0 (name "ubi", size 64 MiB)
[    3.931457] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    3.935876] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    3.942576] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    3.949486] ubi0: good PEBs: 512, bad PEBs: 0, corrupted PEBs: 0
[    3.956265] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    3.962455] ubi0: max/mean erase counter: 12/1, WL threshold: 4096, image sequence number: 0
[    3.969542] ubi0: available PEBs: 136, total reserved PEBs: 376, PEBs reserved for bad PEB handling: 40
[    3.978153] hctosys: unable to open rtc device[    4.009139] Freeing unused kernel memory: 8192K
[    4.045472] init: Console is alive
[    4.045767] init: - watchdog -
[    4.063289] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.069988] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.071844] SCSI subsystem initialized
[    4.080623] ehci-platform: EHCI generic platform driver
[    4.083152] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.085039] ohci-platform: OHCI generic platform driver
[    4.221365] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    4.221461] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    4.226232] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[    4.233519] xhci-hcd xhci-hcd.0.auto: irq 110, io mem 0x11000000
[    4.243461] hub 1-0:1.0: USB hub found
[    4.248960] hub 1-0:1.0: 1 port detected
[    4.252779] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    4.256657] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    4.261871] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0  SuperSpeed
[    4.269581] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.276422] hub 2-0:1.0: USB hub found
[    4.284436] hub 2-0:1.0: 1 port detected
[    4.288146] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    4.291995] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[    4.297499] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[    4.304929] xhci-hcd xhci-hcd.1.auto: irq 111, io mem 0x10000000
[    4.314673] hub 3-0:1.0: USB hub found
[    4.320479] hub 3-0:1.0: 1 port detected
[    4.324313] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    4.328102] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[    4.333466] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0  SuperSpeed
[    4.341015] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.347971] hub 4-0:1.0: USB hub found
[    4.355984] hub 4-0:1.0: 1 port detected
[    4.361164] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.364940] init: - preinit -
[    5.693942] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[    5.695341] dwmac1000: Master AXI performs any burst length
[    5.702849] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[    5.708490] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[    5.718340] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    6.793200] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[    6.793275] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[    8.899424] procd: - early -
[    8.899562] procd: - watchdog -
[    9.550522] procd: - watchdog -
[    9.551021] procd: - ubus -
[    9.605286] procd: - init -
Please press Enter to activate this console.
[    9.709522] kmodloader: loading kernel modules from /etc/modules.d/*
[    9.711344] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    9.718577] Loading modules backported from Linux version v4.19.7-0-g61c68f2a2af0
[    9.720232] Backport generated by backports.git v4.19.7-1-0-g148b072d
[    9.728596] ip_tables: (C) 2000-2006 Netfilter Core Team
[    9.736682] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[    9.761616] xt_time: kernel timezone is -0000
[    9.779861] PPP generic driver version 2.4.2
[    9.781661] NET: Registered protocol family 24
[    9.795285] ath10k 4.16 driver, optimized for CT firmware, probing pci device: 0x40.
[    9.795996] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[    9.802675] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[    9.975599] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:01:00.0.txt failed with error -2
[    9.975643] ath10k_pci 0000:01:00.0: Falling back to user helper
[   10.013864] firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed
[   10.014180] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[   10.021726] ath10k_pci 0000:01:00.0: Falling back to user helper
[   14.259017] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/ct-firmware-5.bin failed with error -2
[   14.259057] ath10k_pci 0000:01:00.0: Falling back to user helper
[   14.307517] firmware ath10k!QCA99X0!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[   14.307788] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/ct-firmware-2.bin failed with error -2
[   14.315843] ath10k_pci 0000:01:00.0: Falling back to user helper
[   14.367096] firmware ath10k!QCA99X0!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[   14.367442] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
[   14.375449] ath10k_pci 0000:01:00.0: Falling back to user helper
[   14.421036] firmware ath10k!QCA99X0!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[   14.422707] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[   14.429027] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   14.441474] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9980-fW-012-620ae964 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT crc32 52695766
[   14.507362] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2
[   15.694480] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   15.694508] ath10k_pci 0000:01:00.0: msdu-desc: 2500  skid: 32
[   15.770280] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   15.771030] ath10k_pci 0000:01:00.0: wmi print 'free: 35468 iram: 35780 sram: 12808'
[   16.013030] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[   16.121879] ath10k 4.16 driver, optimized for CT firmware, probing pci device: 0x40.
[   16.123055] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[   16.129615] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   16.304899] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/fwcfg-pci-0001:01:00.0.txt failed with error -2
[   16.304937] ath10k_pci 0001:01:00.0: Falling back to user helper
[   16.424350] firmware ath10k!fwcfg-pci-0001:01:00.0.txt: firmware_loading_store: map pages failed
[   16.424542] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2
[   16.432201] ath10k_pci 0001:01:00.0: Falling back to user helper
[   21.382164] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/ct-firmware-5.bin failed with error -2
[   21.382212] ath10k_pci 0001:01:00.0: Falling back to user helper
[   21.436034] firmware ath10k!QCA99X0!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[   21.436331] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/ct-firmware-2.bin failed with error -2
[   21.444355] ath10k_pci 0001:01:00.0: Falling back to user helper
[   21.497140] firmware ath10k!QCA99X0!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[   21.497481] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
[   21.505501] ath10k_pci 0001:01:00.0: Falling back to user helper
[   21.555474] firmware ath10k!QCA99X0!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[   21.555602] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[   21.563391] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   21.574658] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9980-fW-012-620ae964 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT crc32 52695766
[   21.641838] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:2 crc32 08fa09f2
[   22.823399] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   22.823426] ath10k_pci 0001:01:00.0: msdu-desc: 2500  skid: 32
[   22.901850] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   22.902632] ath10k_pci 0001:01:00.0: wmi print 'free: 35468 iram: 35780 sram: 12808'
[   23.150497] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[   23.262587] kmodloader: done loading kernel modules from /etc/modules.d/*
[   26.720854] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[   26.721558] dwmac1000: Master AXI performs any burst length
[   26.729828] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[   26.735282] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[   26.744309] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   26.771635] br-lan: port 1(eth1.1) entered blocking state
[   26.771663] br-lan: port 1(eth1.1) entered disabled state
[   26.776270] device eth1.1 entered promiscuous mode
[   26.781386] device eth1 entered promiscuous mode
[   26.796647] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   26.807719] Generic PHY fixed-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00, irq=POLL)
[   26.808427] dwmac1000: Master AXI performs any burst length
[   26.816694] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   26.822087] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[   26.831530] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   26.844112] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   27.754759] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[   27.757885] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   27.763657] br-lan: port 1(eth1.1) entered blocking state
[   27.768708] br-lan: port 1(eth1.1) entered forwarding state
[   27.777502] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   27.913229] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   27.913372] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   27.921991] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready



BusyBox v1.29.3 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r0+8855-dbecc23962
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# sysupgrade http://taiha.net/jenkins/job/OpenWrt-master-BUFFALO-W
XR-2533DHP/lastSuccessfulBuild/artifact/bin/targets/ipq806x/generic/openwrt-ipq8
06x-buffalo_wxr-2533dhp-squashfs-sysupgrade.bin
Downloading 'http://taiha.net/jenkins/job/OpenWrt-master-BUFFALO-WXR-2533DHP/lastSuccessfulBuild/artifact/bin/targets/ipq806x/generic/openwrt-ipq806x-buffalo_wxr-2533dhp-squashfs-sysupgrade.bin'
Connecting to 240b:12:500:65f0:c822:64a3:7e11:4961:80
Writing to '/tmp/sysupgrade.img'
/tmp/sysupgrade.img  100% |*******************************|  4890k  0:00:00 ETA
Download completed (5008076 bytes)
Cannot save config while running from ramdisk.
Commencing upgrade. Closing all shell sessions.
Watchdog handover: fd=3
- watchdog -
killall: telnetd: no process killed
Sending TERM to remaining processes ... ntpd odhcp6c udhcpc dnsmasq ubusd logd netifd odhcpd 
Sending KILL to remaining processes ... 
Performing system upgrade...

created fake-rootfs data: /tmp/fkroot.bin
fake-rootfs data checksum: 0xd0
[   65.679406] ubi1: attaching mtd1
[   66.865186] ubi1: scanning is finished
[   66.888168] ubi1: attached mtd1 (name "rootfs_1", size 64 MiB)
[   66.888194] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[   66.892972] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[   66.899747] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
[   66.906698] ubi1: good PEBs: 512, bad PEBs: 0, corrupted PEBs: 0
[   66.913461] ubi1: user volume: 3, internal volumes: 1, max. volumes count: 128
[   66.919625] ubi1: max/mean erase counter: 6/1, WL threshold: 4096, image sequence number: 1171577802
[   66.926740] ubi1: available PEBs: 136, total reserved PEBs: 376, PEBs reserved for bad PEB handling: 40
[   66.936144] ubi1: background thread "ubi_bgt1d" started, PID 1766
UBI device number 1, total 512 LEBs (65011712 bytes, 62.0 MiB), available 136 LEBs (17268736 bytes, 16.4 MiB), LEB size 126976 bytes (124.0 KiB)
Volume ID 0, size 18 LEBs (2285568 bytes, 2.1 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "kernel", alignment 1
Volume ID 1, size 1 LEBs (126976 bytes, 124.0 KiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "ubi_rootfs", alignment 1
write fake-rootfs data to ubi0_1
Volume ID 2, size 22 LEBs (2793472 bytes, 2.6 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs", alignment 1
Set volume size to 54218752
Volume ID 3, size 427 LEBs (54218752 bytes, 51.7 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs_data", alignment 1
sysupgrade successful
umount: can't unmount /dev: Resource busy
umount: can't unmount /tmp: Resource busy
umount: can't unmount /: Invalid argument
[   71.331901] reboot: Restarting system


BUFFALO WXR-2533DHP U-Boot Ver 1.14 (May 18 2015 - 13:24:36)

CPU:   IPQ8064 clock 1.4 GHz
DRAM:  DDR3 512 MiB clock 533 MHz
NAND:  ECC 4 bits, 256 MiB
SF: Detected W25Q32 with page size 64 KiB, total 4 MiB
MMC:   
In:    serial
Out:   serial
Err:   serial
cdp: get part failed for 0:HLOS
cdp: get part failed for rootfs
Net:   MAC2 addr:74:3:bd:bc:1d:98
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init  done
eth1
Memory Test Start
Pattern: 55555555
Pattern: AAAAAAAA
Pattern: 00000000
Memory Test Pass 

Hit any key to stop autoboot:  0 
Checking Bank1 Image ... 
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000004000000 : "mtd=0"
Bank1 Image is good
kernel_checksum is 0xef770a57 , rootfs_checksum is 0xd0 
Checking Bank2 Image ... 
Creating 1 MTD partitions on "nand0":
0x000004000000-0x000008000000 : "mtd=0"
UBI Volume is empty 
Bank2 Image is fail

NAND erase: device 0 offset 0x4000000, size 0x4000000
Erasing at 0x7fe0000 -- 100% complete.
OK
Creating 1 MTD partitions on "nand0":
0x000004000000-0x000008000000 : "mtd=0"
UBI: empty MTD device detected
UBI: create volume table (copy #1)
UBI: create volume table (copy #2)
Creating dynamic volume kernel of size 5332992
Creating dynamic volume ubi_rootfs of size 31490048
Creating dynamic volume ubi_rootfs_data of size 5332992
Bank2 UBI Partition is Broken
Cpoy to Bank2 Image from Bank1 Image 
Creating 1 MTD partitions on "nand0":
0x000004000000-0x000008000000 : "mtd=0"
2265046 bytes written to volume kernel
158 bytes written to volume ubi_rootfs
MMC Device 0 not found

dmagic1 0 dmagic2 0 
 
MMC Device 0 not found
Using nand device 1
Device 1: nand1... is now current device
bootargs=console=ttyHSL1,115200n8 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs
Booting from flash
set mtdids nand0=nand0 && set mtdparts mtdparts=nand0:0x4000000@0x0(fs),${msmparts} && ubi part fs && ubi read 0x44000000 kernel && bootm 0x44000000
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000004000000 : "mtd=0"
   Image Name:   ARM OpenWrt Linux-4.14.89
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2264982 Bytes = 2.2 MiB
   Load Address: 42208000
   Entry Point:  42208000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
Setting up atags for msm partition: rootfs

device nand0 , # parts = 1
 #: name                size            offset          mask_flags
 0: fs                  0x04000000      0x00000000      0

active partition: nand0,0 - (fs) 0x04000000 @ 0x00000000

defaults:
mtdids  : none
mtdparts: none
Using machid 0x1260 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.89 (jenkins@tofu-z77hvub18_openwrt) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r0+8849-8f8ac4c3dc)) #0 SMP Thu Dec 20 13:01:38 2018
[    0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: Buffalo WXR-2533DHP
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] random: get_random_bytes called from start_kernel+0x88/0x408 with crng_init=0
[    0.000000] percpu: Embedded 15 pages/cpu @ddc01000 s29324 r8192 d23924 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 121920
[    0.000000] Kernel command line: 
[    0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 479436K/491520K available (4745K kernel code, 152K rwdata, 1260K rodata, 1024K init, 228K bss, 12084K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xde800000 - 0xff800000   ( 528 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xde000000   ( 480 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0208000 - 0xc07a25f8   (5738 kB)
[    0.000000]       .init : 0xc0900000 - 0xc0a00000   (1024 kB)
[    0.000000]       .data : 0xc0a00000 - 0xc0a261c0   ( 153 kB)
[    0.000000]        .bss : 0xc0a28000 - 0xc0a610d8   ( 229 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[    0.000006] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[    0.000020] Switching to timer-based delay loop, resolution 160ns
[    0.000233] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[    0.000258] pid_max: default: 32768 minimum: 301
[    0.000380] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000397] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000971] CPU: Testing write buffer coherency: ok
[    0.001739] Setting up static identity map for 0x42300000 - 0x42300060
[    0.001898] Hierarchical SRCU implementation.
[    0.002637] smp: Bringing up secondary CPUs ...
[    0.004460] smp: Brought up 1 node, 2 CPUs
[    0.004478] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[    0.004490] CPU: All CPU(s) started in SVC mode.
[    0.015005] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[    0.015167] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.015193] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.015304] pinctrl core: initialized pinctrl subsystem
[    0.016317] NET: Registered protocol family 16
[    0.016566] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.017921] cpuidle: using governor ladder
[    0.017988] cpuidle: using governor menu
[    0.039324] msm_bus_fabric_init_driver
[    0.040786] usbcore: registered new interface driver usbfs
[    0.040880] usbcore: registered new interface driver hub
[    0.040971] usbcore: registered new device driver usb
[    0.041031] pps_core: LinuxPPS API ver. 1 registered
[    0.041044] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
[    0.041075] PTP clock support registered
[    0.042920] clocksource: Switched to clocksource dg_timer
[    0.046232] NET: Registered protocol family 2
[    0.046750] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.046792] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.046845] TCP: Hash tables configured (established 4096 bind 4096)
[    0.046939] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.046970] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.047163] NET: Registered protocol family 1
[    0.048321] No memory allocated for crashlog
[    0.048588] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[    0.053527] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.053545] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.062791] io scheduler noop registered
[    0.062810] io scheduler deadline registered (default)
[    0.064424] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
[    0.064537] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
[    0.064633] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
[    0.065410] OF: PCI: host bridge /soc/pci@1b500000 ranges:
[    0.065454] OF: PCI:    IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[    0.065479] OF: PCI:   MEM 0x08000000..0x0fdfffff -> 0x08000000
[    0.173117] qcom-pcie 1b500000.pci: link up
[    0.173301] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[    0.173325] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.173344] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[    0.173359] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[    0.173882] PCI: bus0: Fast back to back transfers disabled
[    0.176115] PCI: bus1: Fast back to back transfers disabled
[    0.176213] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[    0.176238] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[    0.176367] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    0.176392] pci 0000:00:00.0:   bridge window [mem 0x08000000-0x081fffff]
[    0.176940] pcieport 0000:00:00.0: AER enabled with IRQ 34
[    0.177494] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
[    0.177588] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
[    0.177701] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
[    0.178452] OF: PCI: host bridge /soc/pci@1b700000 ranges:
[    0.178491] OF: PCI:    IO 0x31e00000..0x31efffff -> 0x31e00000
[    0.178514] OF: PCI:   MEM 0x2e000000..0x31dfffff -> 0x2e000000
[    0.288419] qcom-pcie 1b700000.pci: link up
[    0.288582] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[    0.288603] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.288617] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[    0.289088] PCI: bus0: Fast back to back transfers disabled
[    0.291458] PCI: bus1: Fast back to back transfers disabled
[    0.291542] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[    0.291564] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[    0.291696] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[    0.291716] pci 0001:00:00.0:   bridge window [mem 0x2e000000-0x2e1fffff]
[    0.292223] pcieport 0001:00:00.0: AER enabled with IRQ 67
[    0.294675] L2 @ QSB rate. Forcing new rate.
[    0.294885] L2 @ 384000 KHz
[    0.295056] CPU0 @ 800000 KHz
[    0.295069] CPU1 @ QSB rate. Forcing new rate.
[    0.295188] CPU1 @ 384000 KHz
[    0.299157] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[    0.300554] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0
[    0.301994] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.302840] msm_serial 16340000.serial: msm_serial: detected port #0
[    0.302940] msm_serial 16340000.serial: uartclk = 7372800
[    0.303021] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 100, base_baud = 460800) is a MSM
[    0.303058] msm_serial: console setup on port #0
[    1.035919] console [ttyMSM0] enabled
[    1.040612] msm_serial: driver initialized
[    1.049290] loop: module loaded
[    1.051437] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xaa
[    1.051472] nand: Micron MT29F2G08ABBEAH4
[    1.057952] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.061800] 2 fixed-partitions partitions found on MTD device qcom_nand.0
[    1.069289] Creating 2 MTD partitions on "qcom_nand.0":
[    1.076174] 0x000000000000-0x000004000000 : "ubi"
[    1.088958] random: fast init done
[    1.255704] 0x000004000000-0x000008000000 : "rootfs_1"
[    1.430904] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    1.445696] m25p80 spi0.0: w25q32dw (4096 Kbytes)
[    1.445850] 13 fixed-partitions partitions found on MTD device spi0.0
[    1.449382] Creating 13 MTD partitions on "spi0.0":
[    1.455890] 0x000000000000-0x000000010000 : "SBL1"
[    1.461335] 0x000000010000-0x000000030000 : "MIBIB"
[    1.466187] 0x000000030000-0x000000060000 : "SBL2"
[    1.470890] 0x000000060000-0x000000090000 : "SBL3"
[    1.475866] 0x000000090000-0x0000000a0000 : "DDRCONFIG"
[    1.480512] 0x0000000a0000-0x0000000b0000 : "SSD"
[    1.485713] 0x0000000b0000-0x0000000e0000 : "TZ"
[    1.490482] 0x0000000e0000-0x000000100000 : "RPM"
[    1.495268] 0x000000100000-0x000000170000 : "APPSBL"
[    1.499769] 0x000000170000-0x000000180000 : "APPSBLENV"
[    1.504920] 0x000000180000-0x0000001c0000 : "ART"
[    1.509760] 0x0000001c0000-0x0000001d0000 : "BOOTCONFIG"
[    1.514742] 0x0000001d0000-0x000000240000 : "APPSBL_1"
[    1.520974] libphy: GPIO Bitbanged MDIO: probed
[    1.545534] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[    2.386085] ar8327: qca,phy-rgmii-en is not specified
[    2.386473] libphy: Fixed MDIO Bus: probed
[    2.391822] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[    2.394538] stmmac - user ID: 0x10, Synopsys ID: 0x37
[    2.400628] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[    2.405749] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[    2.411743] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[    2.419796] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[    2.427360] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[    2.434388] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[    2.442204] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[    2.448100] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[    2.455477] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    2.463990] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[    2.470947] stmmac - user ID: 0x10, Synopsys ID: 0x37
[    2.477195] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[    2.482136] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[    2.488278] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[    2.496272] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[    2.503832] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[    2.510784] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[    2.518765] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[    2.524575] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[    2.531878] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    2.539407] i2c /dev entries driver
[    2.548166] Calibration not found.
[    2.550450] qcom-tsens 900000.thermal-sensor: tsens calibration failed
[    2.555169] Speed bin: 0
[    2.560427] PVS bin: 1
[    2.564487] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[    2.565363] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[    2.573013] sdhci: Secure Digital Host Controller Interface driver
[    2.579873] sdhci: Copyright(c) Pierre Ossman
[    2.586116] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.592084] NET: Registered protocol family 10
[    2.597514] Segment Routing with IPv6
[    2.600515] NET: Registered protocol family 17
[    2.605008] 8021q: 802.1Q VLAN Support v1.8
[    2.608556] Registering SWP/SWPB emulation handler
[    2.625077] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[    2.640317] s1a: supplied by regulator-dummy
[    2.640403] s1a: Bringing 0uV into 1050000-1050000uV
[    2.644025] s1b: supplied by regulator-dummy
[    2.648651] s1b: Bringing 0uV into 1050000-1050000uV
[    2.653105] s2a: supplied by regulator-dummy
[    2.657935] s2a: Bringing 0uV into 800000-800000uV
[    2.662294] s2b: supplied by regulator-dummy
[    2.666815] s2b: Bringing 0uV into 800000-800000uV
[    2.676585] UBI: auto-attach mtd0
[    2.676620] ubi0: attaching mtd0
[    2.771894] random: crng init done
[    3.703369] ubi0: scanning is finished
[    3.723698] ubi0: attached mtd0 (name "ubi", size 64 MiB)
[    3.723720] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    3.728068] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    3.734906] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    3.741697] ubi0: good PEBs: 512, bad PEBs: 0, corrupted PEBs: 0
[    3.748528] ubi0: user volume: 4, internal volumes: 1, max. volumes count: 128
[    3.754767] ubi0: max/mean erase counter: 13/1, WL threshold: 4096, image sequence number: 0
[    3.761753] ubi0: available PEBs: 0, total reserved PEBs: 512, PEBs reserved for bad PEB handling: 40
[    3.770525] ubi0: background thread "ubi_bgt0d" started, PID 62
[    3.771636] block ubiblock0_2: created from ubi0:2(rootfs)
[    3.785256] ubiblock: device ubiblock0_2 (rootfs) set to be root file[    3.807236] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    3.809550] Freeing unused kernel memory: 1024K
[    4.218765] init: Console is alive
[    4.218896] init: - watchdog -
[    5.275578] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.338958] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.340910] SCSI subsystem initialized
[    5.349699] ehci-platform: EHCI generic platform driver
[    5.352287] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    5.354237] ohci-platform: OHCI generic platform driver
[    5.491947] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    5.492026] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    5.496767] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[    5.504092] xhci-hcd xhci-hcd.0.auto: irq 110, io mem 0x11000000
[    5.514065] hub 1-0:1.0: USB hub found
[    5.519531] hub 1-0:1.0: 1 port detected
[    5.523408] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    5.527152] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    5.532445] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0  SuperSpeed
[    5.540162] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.547031] hub 2-0:1.0: USB hub found
[    5.555000] hub 2-0:1.0: 1 port detected
[    5.558742] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    5.562572] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[    5.568088] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[    5.575500] xhci-hcd xhci-hcd.1.auto: irq 111, io mem 0x10000000
[    5.585269] hub 3-0:1.0: USB hub found
[    5.591058] hub 3-0:1.0: 1 port detected
[    5.594878] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    5.598678] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[    5.604030] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0  SuperSpeed
[    5.611594] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.618544] hub 4-0:1.0: USB hub found
[    5.626539] hub 4-0:1.0: 1 port detected
[    5.631817] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.644966] init: - preinit -
[    7.476861] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[    7.478368] dwmac1000: Master AXI performs any burst length
[    7.485848] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[    7.491337] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[    7.501189] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    8.553642] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[    8.553713] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   10.773291] UBIFS (ubi0:3): default file-system created
[   11.003900] UBIFS (ubi0:3): background thread "ubifs_bgt0_3" started, PID 146
[   11.259172] UBIFS (ubi0:3): UBIFS: mounted UBI device 0, volume 3, name "rootfs_data"
[   11.259220] UBIFS (ubi0:3): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   11.266118] UBIFS (ubi0:3): FS size: 52948992 bytes (50 MiB, 417 LEBs), journal size 2666496 bytes (2 MiB, 21 LEBs)
[   11.275967] UBIFS (ubi0:3): reserved for root: 2500911 bytes (2442 KiB)
[   11.286250] UBIFS (ubi0:3): media format: w4/r0 (latest is w5/r0), UUID CDD1044B-1045-48AF-83BC-80C1B67A1394, small LPT model
[   11.296754] mount_root: overlay filesystem has not been fully initialized yet
[   11.304594] mount_root: switching to ubifs overlay
[   11.337665] urandom-seed: Seed file not found (/etc/urandom.seed)
[   11.462077] procd: - early -
[   11.462255] procd: - watchdog -
[   12.136573] procd: - watchdog -
[   12.137066] procd: - ubus -
[   12.228244] procd: - init -
Please press Enter to activate this console.
[   12.437084] kmodloader: loading kernel modules from /etc/modules.d/*
[   12.439432] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   12.446643] Loading modules backported from Linux version v4.19.7-0-g61c68f2a2af0
[   12.447797] Backport generated by backports.git v4.19.7-1-0-g148b072d
[   12.456178] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.464372] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[   12.492337] xt_time: kernel timezone is -0000
[   12.518176] PPP generic driver version 2.4.2
[   12.519623] NET: Registered protocol family 24
[   12.532410] ath10k 4.16 driver, optimized for CT firmware, probing pci device: 0x40.
[   12.532920] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[   12.539874] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   12.715891] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:01:00.0.txt failed with error -2
[   12.715934] ath10k_pci 0000:01:00.0: Falling back to user helper
[   12.748124] firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed
[   12.748456] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[   12.756101] ath10k_pci 0000:01:00.0: Falling back to user helper
[   16.824798] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/ct-firmware-5.bin failed with error -2
[   16.824843] ath10k_pci 0000:01:00.0: Falling back to user helper
[   16.867820] firmware ath10k!QCA99X0!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[   16.868131] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/ct-firmware-2.bin failed with error -2
[   16.876143] ath10k_pci 0000:01:00.0: Falling back to user helper
[   16.925109] firmware ath10k!QCA99X0!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[   16.925458] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
[   16.933433] ath10k_pci 0000:01:00.0: Falling back to user helper
[   16.969418] firmware ath10k!QCA99X0!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[   17.409313] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[   17.409344] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   17.419486] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9980-fW-012-620ae964 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT crc32 52695766
[   17.486698] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2
[   18.664895] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   18.664922] ath10k_pci 0000:01:00.0: msdu-desc: 2500  skid: 32
[   18.740771] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   18.741519] ath10k_pci 0000:01:00.0: wmi print 'free: 35468 iram: 35780 sram: 12808'
[   18.983955] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[   19.079243] ath10k 4.16 driver, optimized for CT firmware, probing pci device: 0x40.
[   19.080186] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[   19.086998] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   19.255173] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/fwcfg-pci-0001:01:00.0.txt failed with error -2
[   19.255209] ath10k_pci 0001:01:00.0: Falling back to user helper
[   19.580424] firmware ath10k!fwcfg-pci-0001:01:00.0.txt: firmware_loading_store: map pages failed
[   19.580627] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2
[   19.588378] ath10k_pci 0001:01:00.0: Falling back to user helper
[   21.231532] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/ct-firmware-5.bin failed with error -2
[   21.231577] ath10k_pci 0001:01:00.0: Falling back to user helper
[   21.274512] firmware ath10k!QCA99X0!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[   21.274782] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/ct-firmware-2.bin failed with error -2
[   21.282722] ath10k_pci 0001:01:00.0: Falling back to user helper
[   21.352406] firmware ath10k!QCA99X0!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[   21.352671] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
[   21.360763] ath10k_pci 0001:01:00.0: Falling back to user helper
[   21.411628] firmware ath10k!QCA99X0!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[   21.411830] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[   21.419580] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   21.431185] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9980-fW-012-620ae964 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT crc32 52695766
[   21.498050] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:2 crc32 08fa09f2
[   22.680151] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   22.680183] ath10k_pci 0001:01:00.0: msdu-desc: 2500  skid: 32
[   22.757948] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   22.758726] ath10k_pci 0001:01:00.0: wmi print 'free: 35468 iram: 35780 sram: 12808'
[   23.007042] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[   23.112941] kmodloader: done loading kernel modules from /etc/modules.d/*
[   27.460773] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[   27.461478] dwmac1000: Master AXI performs any burst length
[   27.469761] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[   27.475195] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[   27.484226] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   27.510929] br-lan: port 1(eth1.1) entered blocking state
[   27.510958] br-lan: port 1(eth1.1) entered disabled state
[   27.515560] device eth1.1 entered promiscuous mode
[   27.520682] device eth1 entered promiscuous mode
[   27.551804] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   27.558909] Generic PHY fixed-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00, irq=POLL)
[   27.559615] dwmac1000: Master AXI performs any burst length
[   27.567874] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   27.573330] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[   27.582682] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   27.600269] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   28.563399] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[   28.566617] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   28.571700] br-lan: port 1(eth1.1) entered blocking state
[   28.577429] br-lan: port 1(eth1.1) entered forwarding state
[   28.595765] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   28.633401] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   28.633475] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   28.649836] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready



BusyBox v1.29.3 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r0+8855-dbecc23962
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# ubus call system board
{
        "kernel": "4.14.89",
        "hostname": "OpenWrt",
        "system": "ARMv7 Processor rev 0 (v7l)",
        "model": "Buffalo WXR-2533DHP",
        "board_name": "buffalo,wxr-2533dhp",
        "release": {
                "distribution": "OpenWrt",
                "version": "SNAPSHOT",
                "revision": "r0+8855-dbecc23962",
                "target": "ipq806x\/generic",
                "description": "OpenWrt SNAPSHOT r0+8855-dbecc23962"
        }
}
広告

コメントを残す

以下に詳細を記入するか、アイコンをクリックしてログインしてください。

WordPress.com ロゴ

WordPress.com アカウントを使ってコメントしています。 ログアウト /  変更 )

Google フォト

Google アカウントを使ってコメントしています。 ログアウト /  変更 )

Twitter 画像

Twitter アカウントを使ってコメントしています。 ログアウト /  変更 )

Facebook の写真

Facebook アカウントを使ってコメントしています。 ログアウト /  変更 )

%s と連携中