Aterm WR8750NのNECオリジナル (?) なBootloaderを、musashino-build/u-boot_modからビルドしたU-Bootに置き換えてブートしたログのメモ。
上記リポジトリからのビルドはWSLで問題無く行えた。
全体的な流れとしては以下の通り。
- NECのBootloader上でOpenWrtのNEC用initramfsイメージ (initramfs-necimg) をPCから転送し、
boot
コマンドを実行してOpenWrtをブート - initramfs上でU-Bootパーティション内を
mtd erase u-boot
で消去し、scp等で転送しておいたU-Bootをmtd write ファイル名 u-boot
で書き込み - wget等でダウンロードしたOpenWrt sysupgradeイメージを
sysupgrade ファイル名
でFlashへ書き込み reboot
で再起動し、U-BootによりOpenWrtが起動される
IPL:HARD-RESET memory test ... ok flinstall OK boot version: 1.0.0 PKG "Orthos-HP" CPU "Atheros/AR9344" Revision 212.1 CLOCK 560.0 MHz HEAP MEMORY 262144 bytes Boot:InitFilesystem phy0.1: "Atheros/AR8327(SW)" phy0.0: "Atheros/AR8327(phy)" active ch:0 post start DRAM Test ..... PASS Timer test .... PASS FLASH CHKSUM .. PASS LAN Test ..... LoopBack count 0 .. phy0.1: "Atheros/AR8327(SW)" phy0.0: "Atheros/AR8327(phy)" active ch:0 active ch:1 phy0.1: "Atheros/AR8327(SW)" phy0.0: "Atheros/AR8327(phy)" active ch:0 PASS Package TYPE = 0x01 post success welcome to boot console Password: boot> tftpd tftpd start 192.168.0.1 boot> start tftp load openwrt-ath79-tiny-nec_wr8750n-i end tftp load length = 3224648 start memory load ... memory load complete begin : 0x80060000 length : 3224624 startup: 0x80060000 boot begin : 0x80060000 length : 3224624 startup: 0x80060000 option: 0x0 OpenWrt kernel loader for AR7XXX/AR9XXX Copyright (C) 2011 Gabor Juhos Decompressing kernel... done! Starting kernel at 80060000... [ 0.000000] Linux version 4.14.95 (musashino205@Taiha.Net) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r0+9120-bad68ff519)) #0 Fri Jan 25 10:38:20 2019 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] MIPS: machine is NEC Aterm WR8750N [ 0.000000] SoC: Atheros AR9344 rev 1 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] random: get_random_bytes called from 0x8045972c with crng_init=0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,9600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 118520K/131072K available (3450K kernel code, 138K rwdata, 472K rodata, 6684K init, 195K bss, 12552K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] CPU clock: 560.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6825930166 ns [ 0.000010] sched_clock: 32 bits at 280MHz, resolution 3ns, wraps every 7669584382ns [ 0.092710] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688) [ 0.237627] pid_max: default: 32768 minimum: 301 [ 0.293070] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.372220] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.461164] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.578797] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.651743] pinctrl core: initialized pinctrl subsystem [ 0.715209] NET: Registered protocol family 16 [ 0.769108] Can't analyze schedule() prologue at 803ba57c [ 0.836108] PCI host bridge /ahb/apb/pcie-controller@180c0000 ranges: [ 0.913158] MEM 0x0000000010000000..0x0000000013ffffff [ 0.975619] IO 0x0000000000000000..0x0000000000000000 [ 1.055718] PCI host bridge to bus 0000:00 [ 1.104729] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 1.186947] pci_bus 0000:00: root bus resource [io 0x0000] [ 1.253610] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 1.334834] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.430150] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit] [ 1.517607] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref] [ 1.604603] clocksource: Switched to clocksource MIPS [ 1.666172] NET: Registered protocol family 2 [ 1.719143] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 1.802472] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 1.878458] TCP: Hash tables configured (established 1024 bind 1024) [ 1.954632] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 2.024379] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 2.099600] NET: Registered protocol family 1 [ 2.287387] Crashlog allocated RAM at address 0x3f00000 [ 2.351273] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 2.433343] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.503096] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 2.694948] io scheduler noop registered [ 2.741872] io scheduler deadline registered (default) [ 2.803622] ar7200-usb-phy usb-phy: phy reset is missing [ 2.869384] pinctrl-single 1804002c.pinmux: 544 pins at pa b804002c size 68 [ 2.953240] gpio-export gpio-export: 1 gpio(s) exported [ 3.016545] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 3.093326] console [ttyS0] disabled [ 3.136081] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 8, base_baud = 2500000) is a 16550A [ 3.239096] console [ttyS0] enabled [ 3.239096] console [ttyS0] enabled [ 3.322380] bootconsole [early0] disabled [ 3.322380] bootconsole [early0] disabled [ 3.424777] m25p80 spi0.0: mx25l6405d (8192 Kbytes) [ 3.483123] 4 fixed-partitions partitions found on MTD device spi0.0 [ 3.559091] Creating 4 MTD partitions on "spi0.0": [ 3.616401] 0x000000000000-0x000000020000 : "u-boot" [ 3.676618] 0x000000020000-0x000000030000 : "config" [ 3.736846] 0x000000030000-0x000000040000 : "art" [ 3.793959] 0x000000040000-0x000000800000 : "firmware" [ 3.865576] libphy: Fixed MDIO Bus: probed [ 4.255004] libphy: ag71xx_mdio: probed [ 4.325525] switch0: Atheros AR8327 rev. 2 switch registered on mdio-bus.0 [ 5.395782] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:00 [uid=004dd033, driver=Atheros AR8216/AR8236/AR8316] [ 5.524437] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII [ 5.599250] NET: Registered protocol family 10 [ 5.656142] Segment Routing with IPv6 [ 5.700080] NET: Registered protocol family 17 [ 5.753601] 8021q: 802.1Q VLAN Support v1.8 [ 5.838232] Freeing unused kernel memory: 6684K [ 5.892449] This architecture does not have kernel memory protection. [ 5.983133] init: Console is alive [ 6.024138] init: - watchdog - [ 6.083426] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 6.176339] usbcore: registered new interface driver usbfs [ 6.242093] usbcore: registered new interface driver hub [ 6.305741] usbcore: registered new device driver usb [ 6.372177] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.452109] ehci-platform: EHCI generic platform driver [ 6.514893] ehci-platform 1b000000.usb: EHCI Host Controller [ 6.582642] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1 [ 6.676386] ehci-platform 1b000000.usb: irq 3, io mem 0x1b000000 [ 6.754626] random: fast init done [ 6.795359] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00 [ 6.870269] hub 1-0:1.0: USB hub found [ 6.915582] hub 1-0:1.0: 1 port detected [ 6.964055] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 7.060951] init: - preinit - [ 7.317977] random: jshn: uninitialized urandom read (4 bytes read) [ 7.393053] usb 1-1: new full-speed USB device number 2 using ehci-platform [ 7.567222] random: jshn: uninitialized urandom read (4 bytes read) [ 7.757421] usb 1-1: not running at top speed; connect to a high speed hub [ 7.927281] random: procd: uninitialized urandom read (4 bytes read) [ 8.003845] hub 1-1:1.0: USB hub found [ 8.079136] hub 1-1:1.0: 4 ports detected [ 8.356563] urandom_read: 3 callbacks suppressed [ 8.356572] random: jshn: uninitialized urandom read (4 bytes read) [ 8.580817] random: jshn: uninitialized urandom read (4 bytes read) [ 9.420930] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9.490871] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 10.615880] eth0: link up (1000Mbps/Full duplex) [ 10.673431] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 10.758074] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 12.847691] procd: - early - [ 12.882294] procd: - watchdog - [ 13.466291] procd: - watchdog - [ 13.504146] procd: - ubus - [ 13.545399] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.622629] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.700245] procd: - init - Please press Enter to activate this console. [ 13.814685] eth0: link down [ 13.957775] kmodloader: loading kernel modules from /etc/modules.d/* [ 14.038310] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 14.113503] Loading modules backported from Linux version v4.19.7-0-g61c68f2a2af0 [ 14.203132] Backport generated by backports.git v4.19.7-1-0-g148b072d [ 14.283182] ip_tables: (C) 2000-2006 Netfilter Core Team [ 14.355187] nf_conntrack version 0.5.0 (2048 buckets, 8192 max) [ 14.482215] xt_time: kernel timezone is -0000 [ 14.591245] PPP generic driver version 2.4.2 [ 14.644938] NET: Registered protocol family 24 [ 14.756524] ieee80211 phy0: Atheros AR9340 Rev:1 mem=0xb8100000, irq=11 [ 14.839676] ath9k 0000:00:00.0: Direct firmware load for ath9k-eeprom-pci-0000:00:00.0.bin failed with error -2 [ 14.960456] ath9k 0000:00:00.0: Falling back to user helper [ 15.451439] ieee80211 phy1: Atheros AR9300 Rev:3 mem=0xb0000000, irq=14 [ 15.635030] kmodloader: done loading kernel modules from /etc/modules.d/* [ 27.252549] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 27.323758] eth0: link up (1000Mbps/Full duplex) [ 27.514688] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 27.616125] br-lan: port 1(eth0.1) entered blocking state [ 27.680694] br-lan: port 1(eth0.1) entered disabled state [ 27.745685] device eth0.1 entered promiscuous mode [ 27.802981] device eth0 entered promiscuous mode [ 28.186022] br-lan: port 1(eth0.1) entered blocking state [ 28.250603] br-lan: port 1(eth0.1) entered forwarding state [ 28.317426] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 28.389650] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready BusyBox v1.30.0 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r0+9135-d6efa74437 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/# vi /etc/config/network root@OpenWrt:/# vi /etc/config/firewall root@OpenWrt:/# (実際には network と firewall の restart をしているが省略) root@OpenWrt:/tmp# cd /tmp root@OpenWrt:/tmp# wget http://taiha.net/jenkins/job/OpenWrt-master-NEC-WR8750N/ lastSuccessfulBuild/artifact/bin/targets/ath79/tiny/openwrt-ath79-tiny-nec_wr875 0n-squashfs-sysupgrade.bin Downloading 'http://taiha.net/jenkins/job/OpenWrt-master-NEC-WR8750N/lastSuccessfulBuild/artifact/bin/targets/ath79/tiny/openwrt-ath79-tiny-nec_wr8750n-squashfs-sysupgrade.bin' Connecting to 240b:12:500:65f0:c822:64a3:7e11:4961:80 Writing to 'openwrt-ath79-tiny-nec_wr8750n-squashfs-sysupgrade.bin' openwrt-ath79-tiny-n 100% |*******************************| 3328k 0:00:00 ETA Download completed (3408582 bytes) root@OpenWrt:/tmp# ls -alh drwxrwxrwt 15 root root 460 Jan 26 16:46 . drwxr-xr-x 16 root root 0 Jan 1 1970 .. -rwx------ 1 root root 5 Jan 25 10:44 .switch2jffs drwx------ 2 root root 120 Jan 25 10:44 .uci -rw-r--r-- 1 root root 4 Jan 25 10:44 TZ -rw-r--r-- 1 root root 857 Jan 1 1970 board.json -rw-r--r-- 1 root root 0 Jan 25 10:44 dhcp.leases drwxr-xr-x 2 root root 40 Jan 25 10:44 dnsmasq.d drwxr-xr-x 2 root root 40 Jan 25 10:44 dropbear drwxr-xr-x 2 root root 60 Jan 26 16:45 etc drwxr-xr-x 2 root root 80 Jan 26 16:45 hosts drwxr-xr-x 3 root root 60 Jan 25 10:44 lib drwxr-xr-x 2 root root 280 Jan 25 10:44 lock drwxr-xr-x 2 root root 80 Jan 25 10:44 log -rw-r--r-- 1 root root 3.3M Jan 26 16:46 openwrt-ath79-tiny-nec_wr8750n-squashfs-sysupgrade.bin -rw-r--r-- 1 root root 32 Jan 26 16:45 resolv.conf -rw-r--r-- 1 root root 140 Jan 26 16:45 resolv.conf.auto drwxr-xr-x 3 root root 200 Jan 26 16:45 run drwxrwxrwt 2 root root 40 Jan 1 1970 shm drwxr-xr-x 2 root root 80 Jan 26 16:44 state drwxr-xr-x 2 root root 80 Jan 1 1970 sysinfo drwxr-xr-x 2 root root 40 Jan 25 10:44 tmp -rw-r--r-- 1 root root 128.0K Jan 26 16:45 u-boot_mod__nec_wr8750n__20190127__git_nec-devs-398303cd.bin root@OpenWrt:/tmp# cat /proc/mtd dev: size erasesize name mtd0: 00020000 00010000 "u-boot" mtd1: 00010000 00010000 "config" mtd2: 00010000 00010000 "art" mtd3: 007c0000 00010000 "firmware" root@OpenWrt:/tmp# mtd erase u-boot&&mtd write u-boot_mod__nec_wr8750n__20190127 __git_nec-devs-398303cd.bin u-boot Unlocking u-boot ... Erasing u-boot ... Unlocking u-boot ... Writing from u-boot_mod__nec_wr8750n__20190127__git_nec-devs-398303cd.bin to u-boot ... root@OpenWrt:/tmp# mtd erase firmware&&sysupgrade openwrt-ath79-tiny-nec_wr8750n -squashfs-sysupgrade.bin Unlocking firmware ... Erasing firmware ... Cannot save config while running from ramdisk. Commencing upgrade. Closing all shell sessions. Watchdog handover: fd=3 - watchdog - killall: telnetd: no process kilSending TERM to remaining processes ... ntpd netifd dnsmasq ubusd logd odhcpd Sending KILL to remaining processes ... Performing system upgrade... Unlocking firmware ... Writing from to firmware ... Upgrade completed Rebooting system... umount: can[ 329.834295] reboot: Restarting system *************************************** * U-Boot 1.1.4-398303cd-clean * * Build: 2019-01-26 * *************************************** BOARD: NEC Aterm WR8750N SOC: AR9344 rev. 1 CPU: MIPS 74Kc RAM: 128 MB DDR2 32-bit CL3-4-4-10 FLASH: 8 MB Macronix MX25L64 PCIe: 168C:0030 MAC: 1C:B1:7F:00:A5:00 CLOCKS: CPU/RAM/AHB/SPI/REF 550/400/200/ 25/ 40 MHz Hit any key to stop booting: 0 Booting image from 0x9F040000... Image name: MIPS OpenWrt Linux-4.14.95 Build date: 2019-01-25 10:38:20 UTC Architecture: MIPS OS/image type: Linux Kernel Compression: LZMA Data size: 1.3 MB (1377507 bytes) Load address: 0x80060000 Entry point: 0x80060000 Header CRC... OK! Data CRC... skipped Uncompressing Kernel... OK! Starting kernel... [ 0.000000] Linux version 4.14.95 (musashino205@Taiha.Net) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r0+9120-bad68ff519)) #0 Fri Jan 25 10:38:20 2019 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] MIPS: machine is NEC Aterm WR8750N [ 0.000000] SoC: Atheros AR9344 rev 1 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] random: get_random_bytes called from 0x8045972c with crng_init=0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,9600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 124024K/131072K available (3450K kernel code, 138K rwdata, 472K rodata, 1180K init, 195K bss, 7048K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] CPU clock: 550.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6950037990 ns [ 0.000010] sched_clock: 32 bits at 275MHz, resolution 3ns, wraps every 7809031678ns [ 0.092710] Calibrating delay loop... 274.02 BogoMIPS (lpj=1370112) [ 0.237624] pid_max: default: 32768 minimum: 301 [ 0.293075] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.372219] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.461334] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.579005] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.651955] pinctrl core: initialized pinctrl subsystem [ 0.715480] NET: Registered protocol family 16 [ 0.769365] Can't analyze schedule() prologue at 803ba57c [ 0.836528] PCI host bridge /ahb/apb/pcie-controller@180c0000 ranges: [ 0.913575] MEM 0x0000000010000000..0x0000000013ffffff [ 0.976032] IO 0x0000000000000000..0x0000000000000000 [ 1.057392] PCI host bridge to bus 0000:00 [ 1.106394] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 1.188608] pci_bus 0000:00: root bus resource [io 0x0000] [ 1.255271] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 1.336495] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.431798] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit] [ 1.519271] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref] [ 1.606296] clocksource: Switched to clocksource MIPS [ 1.667912] NET: Registered protocol family 2 [ 1.720850] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 1.804244] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 1.880225] TCP: Hash tables configured (established 1024 bind 1024) [ 1.956394] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 2.026165] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 2.101392] NET: Registered protocol family 1 [ 2.158566] Crashlog allocated RAM at address 0x3f00000 [ 2.222441] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 2.304735] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.374555] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 2.500796] io scheduler noop registered [ 2.547715] io scheduler deadline registered (default) [ 2.609478] ar7200-usb-phy usb-phy: phy reset is missing [ 2.675292] pinctrl-single 1804002c.pinmux: 544 pins at pa b804002c size 68 [ 2.759184] gpio-export gpio-export: 1 gpio(s) exported [ 2.822531] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 2.899409] console [ttyS0] disabled [ 2.942227] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 8, base_baud = 2500000) is a 16550A [ 3.045239] console [ttyS0] enabled [ 3.045239] console [ttyS0] enabled [ 3.128517] bootconsole [early0] disabled [ 3.128517] bootconsole [early0] disabled [ 3.231279] m25p80 spi0.0: mx25l6405d (8192 Kbytes) [ 3.289704] 4 fixed-partitions partitions found on MTD device spi0.0 [ 3.365749] Creating 4 MTD partitions on "spi0.0": [ 3.423059] 0x000000000000-0x000000020000 : "u-boot" [ 3.483355] 0x000000020000-0x000000030000 : "config" [ 3.543649] 0x000000030000-0x000000040000 : "art" [ 3.600733] 0x000000040000-0x000000800000 : "firmware" [ 3.666465] 2 uimage-fw partitions found on MTD device firmware [ 3.737249] Creating 2 MTD partitions on "firmware": [ 3.796624] 0x000000000000-0x000000160000 : "kernel" [ 3.856899] 0x000000160000-0x0000007c0000 : "rootfs" [ 3.917058] mtd: device 5 (rootfs) set to be root filesystem [ 3.984821] 1 squashfs-split partitions found on MTD device rootfs [ 4.058716] 0x000000340000-0x0000007c0000 : "rootfs_data" [ 4.124812] libphy: Fixed MDIO Bus: probed [ 4.506712] libphy: ag71xx_mdio: probed [ 4.555438] switch0: Atheros AR8327 rev. 2 switch registered on mdio-bus.0 [ 5.627485] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:00 [uid=004dd033, driver=Atheros AR8216/AR8236/AR8316] [ 5.756199] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII [ 5.831182] NET: Registered protocol family 10 [ 5.888262] Segment Routing with IPv6 [ 5.932207] NET: Registered protocol family 17 [ 5.985755] 8021q: 802.1Q VLAN Support v1.8 [ 6.043808] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 6.134309] Freeing unused kernel memory: 1180K [ 6.188536] This architecture does not have kernel memory protection. [ 6.616309] random: fast init done [ 7.558574] init: Console is alive [ 7.599449] init: - watchdog - [ 9.015969] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 9.346480] usbcore: registered new interface driver usbfs [ 9.412201] usbcore: registered new interface driver hub [ 9.475868] usbcore: registered new device driver usb [ 9.542808] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 9.628845] ehci-platform: EHCI generic platform driver [ 9.691687] ehci-platform 1b000000.usb: EHCI Host Controller [ 9.759417] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1 [ 9.853165] ehci-platform 1b000000.usb: irq 3, io mem 0x1b000000 [ 9.946342] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00 [ 10.021296] hub 1-0:1.0: USB hub found [ 10.066595] hub 1-0:1.0: 1 port detected [ 10.115141] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 10.212057] init: - preinit - [ 10.778066] random: jshn: uninitialized urandom read (4 bytes read) [ 11.190636] random: jshn: uninitialized urandom read (4 bytes read) [ 11.522880] random: jshn: uninitialized urandom read (4 bytes read) [ 11.810029] urandom_read: 2 callbacks suppressed [ 11.810039] random: jshn: uninitialized urandom read (4 bytes read) [ 12.034683] random: jshn: uninitialized urandom read (4 bytes read) [ 13.691134] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 13.761000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready Press the [f] ke[ 13.909259] random: procd: uninitialized urandom read (4 bytes read) y and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 14.857581] eth0: link up (1000Mbps/Full duplex) [ 14.915225] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 15.000181] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 17.647193] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 17.756597] urandom-seed: Seed file not found (/etc/urandom.seed) [ 17.875873] procd: - early - [ 17.911400] procd: - watchdog - [ 18.199682] eth0: link down [ 18.778769] procd: - watchdog - [ 18.816676] procd: - ubus - [ 19.144234] random: ubusd: uninitialized urandom read (4 bytes read) [ 19.457893] random: ubusd: uninitialized urandom read (4 bytes read) [ 19.535490] procd: - init - [ 20.046501] kmodloader: loading kernel modules from /etc/modules.d/* Please press Ent[ 20.130027] ip6_tables: (C) 2000-2006 Netfilter Core Team er to activate this console. [ 20.224348] Loading modules backported from Linux version v4.19.7-0-g61c68f2a2af0 [ 20.326844] Backport generated by backports.git v4.19.7-1-0-g148b072d [ 20.406992] ip_tables: (C) 2000-2006 Netfilter Core Team [ 20.479545] nf_conntrack version 0.5.0 (2048 buckets, 8192 max) [ 20.613705] xt_time: kernel timezone is -0000 [ 20.728057] PPP generic driver version 2.4.2 [ 20.781904] NET: Registered protocol family 24 [ 20.897124] ieee80211 phy0: Atheros AR9340 Rev:1 mem=0xb8100000, irq=11 [ 20.976739] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 21.047575] ath9k 0000:00:00.0: Direct firmware load for ath9k-eeprom-pci-0000:00:00.0.bin failed with error -2 [ 21.168303] ath9k 0000:00:00.0: Falling back to user helper [ 22.540103] ieee80211 phy1: Atheros AR9300 Rev:3 mem=0xb0000000, irq=14 [ 22.726761] kmodloader: done loading kernel modules from /etc/modules.d/* [ 35.363450] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 35.676398] jffs2_build_filesystem(): unlocking the mtd device... [ 35.676408] done. [ 35.773289] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 42.288637] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 42.449264] eth0: link up (1000Mbps/Full duplex) [ 42.704270] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 43.051540] br-lan: port 1(eth0.1) entered blocking state [ 43.116163] br-lan: port 1(eth0.1) entered disabled state [ 43.181054] device eth0.1 entered promiscuous mode [ 43.238342] device eth0 entered promiscuous mode [ 43.967602] br-lan: port 1(eth0.1) entered blocking state [ 44.032161] br-lan: port 1(eth0.1) entered forwarding state [ 44.099022] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 44.306378] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 70.976475] done. [ 70.999489] jffs2: notice: (1031) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 71.716188] overlayfs: upper fs does not support tmpfile. [ 136.435551] random: crng init done BusyBox v1.30.0 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r0+9135-d6efa74437 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/#
広告