WG1200CR stock -> OpenWrt (ath79)

1つ前の記事で書いた通り、Cのプログラムをでっち上げたのでそれを利用してfactoryを生成。メーカーファームからの投入を試行したのでメモ。

log

[ephp.c read_operand_list 1234] PHP operator precedence issue at: /htdocs/webinc/js/tools_fw_rlt.php, operand_qty: 6, add_qty: 2, mul_qty: 3
SERVD: event [PREFWUPDATE/default]
[/etc/scripts/prefwupdate.sh] ....
SERVD: stop service [THERMAL]
Stop THERMAL service ..
SERVD: event [STATUS.CRITICAL] not found!
SERVD: stop service [WAN]
SERVD: stop service [WIFI]
SERVD: service [WIFI] is already stopped.
SERVD: stop service [LAN]
SERVD: stop service [INET.WAN-1]
[/var/servd/INET.WAN-1_stop.sh]: stopping WAN-1...
[/var/servd/WAN-1-udhcpc.sh]: deconfig eth0.2 ...
SERVD: event [WAN-1.DOWN/default]
[/var/servd/INET.WAN-1_stop.sh]: stopping WAN-1 done !!!
SERVD: stop service [INET.WAN-2]
SERVD: service [INET.WAN-2] is already stopped.
SERVD: stop service [INET.WAN-3]
SERVD: service [INET.WAN-3] is already stopped.
SERVD: stop service [INET.WAN-4]
SERVD: service [INET.WAN-4] is already stopped.
SERVD: stop service [INET.WAN-5]
SERVD: service [INET.WAN-5] is already stopped.
SERVD: stop service [IPT.WAN-1]
SERVD: stop service [IPT.WAN-2]
SERVD: stop service [IPT.WAN-3]
SERVD: stop service [IPT.WAN-4]
SERVD: stop service [IPT.WAN-5]
SERVD: service [IPT.WAN-5] is already stopped.
SERVD: stop service [IPTDMZ]
SERVD: stop service [IPTPORTT]
SERVD: stop service [IPTPFWD]
SERVD: stop service [IPTVSVR]
iptables: No chain/target/match by that name.
SERVD: stop service [IPTMASQ]
SERVD: stop service [INET.LAN-1]
[/var/servd/INET.LAN-1_stop.sh]: stopping LAN-1...
SERVD: event [LAN-1.DOWN/default]
/var/run/phpsh-14632.sh: line 6: can't create /proc/nf_accelerate_to_local: nonexistent directory
[/var/servd/INET.LAN-1_stop.sh]: stopping LAN-1 done !!!
SERVD: stop service [INET.LAN-2]
SERVD: service [INET.LAN-2] is already stopped.
SERVD: stop service [INET.LAN-4]
SERVD: service [INET.LAN-4] is already stopped.
SERVD: stop service [INET.LAN-5]
SERVD: service [INET.LAN-5] is already stopped.
SERVD: stop service [INET.LAN-6]
SERVD: service [INET.LAN-6] is already stopped.
SERVD: stop service [IPT.LAN-1]
SERVD: stop service [IPT.LAN-2]
SERVD: stop service [IPT.LAN-3]
SERVD: service [IPT.LAN-3] is already stopped.
SERVD: stop service [IPT.LAN-4]
SERVD: service [IPT.LAN-4] is already stopped.
SERVD: stop service [IPT.LAN-5]
SERVD: service [IPT.LAN-5] is already stopped.
SERVD: stop service [IPT.LAN-6]
SERVD: service [IPT.LAN-6] is already stopped.
SERVD: stop service [ACCESSCTRL]
SERVD: stop service [INFSVCS.WAN-1]
SERVD: event [INFSVCS.WAN-1.DOWN] not found!
SERVD: event [UPNP.IGD.NOTIFY.WANIPCONN1/default]
SERVD: event [UPDATERESOLV/default]
SERVD: event [WAN-1.DISCONNECTED/default]
SERVD: stop service [HTTP]
SERVD: event [HTTP.DOWN/default]
SERVD: stop service [INFSVCS.LAN-1]
[/etc/events/FWUPDATER.sh] ...
kill servd, xmldb, watchdog, and load.sh
copy upgrade needed file to ramfs
remout /www /htdocs /etc /usr /bin /sbin to empty ramfs avoid someone access rootfs
FWUPDATER: about to write 4259844 bytes data to /dev/mtdblock/6
[  539.180000] ATT:001[SYN-ACK]:IN=br0 OUT= MAC=98:f1:99:f2:1d:24:5c:9a:d8:e6:3f:b3:08:00 SRC=192.168.10.101 DST=88.99.186.153 LEN=263 TOS=0x00 PREC=0x00 TTL=129 ID=23596 PROTO=TCP SPT=49877 DPT=443 WINDOW=65535 RES=0x00 ACK PSH URGP=0 
[  539.410000] ATT:001[SYN-ACK]:IN=br0 OUT= MAC=98:f1:99:f2:1d:24:5c:9a:d8:e6:3f:b3:08:00 SRC=192.168.10.101 DST=88.99.186.153 LEN=263 TOS=0x00 PREC=0x00 TTL=129 ID=23597 PROTO=TCP SPT=49876 DPT=443 WINDOW=65535 RES=0x00 ACK PSH URGP=0 
[  554.070000] ATT:001[SYN-ACK]:IN=br0 OUT= MAC=98:f1:99:f2:1d:24:5c:9a:d8:e6:3f:b3:08:00 SRC=192.168.10.101 DST=88.99.186.153 LEN=263 TOS=0x00 PREC=0x00 TTL=129 ID=23598 DF PROTO=TCP SPT=49877 DPT=443 WINDOW=65535 RES=0x00 ACK PSH URGP=0 
[  554.380000] ATT:001[SYN-ACK]:IN=br0 OUT= MAC=98:f1:99:f2:1d:24:5c:9a:d8:e6:3f:b3:08:00 SRC=192.168.10.101 DST=88.99.186.153 LEN=263 TOS=0x00 PREC=0x00 TTL=129 ID=23599 DF PROTO=TCP SPT=49876 DPT=443 WINDOW=65535 RES=0x00 ACK PSH URGP=0 
[  556.070000] ATT:001[SYN-ACK]:IN=eth0.2 OUT= MAC=98:f1:99:f2:1d:25:00:25:36:14:e9:8c:08:00:45:00:00:47 SRC=178.63.70.146 DST=192.168.1.65 LEN=71 TOS=0x00 PREC=0x00 TTL=51 ID=33765 DF PROTO=TCP SPT=443 DPT=49879 WINDOW=26800 RES=0x00 ACK PSH URGP=0 
FWUPDATER: cost 32.573702 seconds
fwupdate: unable to read SEAMA header!
/etc/events/FWUPDATER.sh: line 44: ca[  571.750000] ath_vap_stopping=1
n't create /proc/driver/system_reset: nonexistent directory
/etc/events/FWUPDATER.sh: line 45: can't create /proc/system_reset: nonexistent directory
The system is going down NOW!
Sent SIGTERM to all processes
[  571.790000] mlme_create_infra_bss : Overriding HT40 channel with HT20 channel
[  571.830000] __ieee80211_smart_ant_init: Smart Antenna is not supported 
[  571.840000] ol_ath_vap_stopping=1
[  571.840000] STOPPED EVENT for vap 0 (8788c000)
[  571.850000] send_vdev_down_cmd_non_tlv for vap 0
[  571.880000] OL vap_start +
[  571.880000] VDEV START
[  571.880000] OL vap_start -
[  571.880000] ol_vdev_start_resp_ev for vap 0 (8788c000)
[  571.890000] su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1
[  571.900000] send_vdev_up_cmd_non_tlv for vap 0
[  571.900000] ol_ath_vap_up=1
[  571.900000] __ieee80211_smart_ant_init: Smart Antenna is not supported 
[  571.910000] ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3
[  571.920000] ol_ath_vap_set_param: Now supported MCAST RATE is 6000(kbps) and rate code: 0x3
[  572.630000] [wifi1] FWLOG: [593155] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
[  572.640000] [wifi1] FWLOG: [593171] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
[  572.640000] [wifi1] FWLOG: [593171] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
[  572.650000] [wifi1] FWLOG: [593200] vap-0 VDEV_MGR_VDEV_START ( 0x1450, 0x2, 0x0, 0x0 )
[  572.660000] [wifi1] FWLOG: [593200] UNKNOWN 14:20 ( 0x0 )
[  572.660000] [wifi1] FWLOG: [593221] VDEV_MGR_HP_START_TIME ( 0x0, 0x1450, 0x21534000 )
[  572.670000] [wifi1] FWLOG: [593221] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x1 )
[  572.680000] [wifi1] FWLOG: [593221] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
[  572.690000] [wifi1] FWLOG: [593221] VDEV_MGR_AP_TBTT_CONFIG ( 0x0, 0x1450, 0x0, 0x0 )
Sent SIGKILL to all processes
Requesting system reboot
[  573.770000] Restarting system.


U-Boot 1.1.4 (Nov  1 2017 - 20:40:33)

SVN revision: 1501
ap152 - Dragonfly 1.0DRAM:  
sri
ath_ddr_initial_config(278): (ddr2 init)
ath_sys_frequency: cpu 775 ddr 650 ahb 258
Tap values = (0x10, 0x10, 0x10, 0x10)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 304k for U-Boot at: 87fb0000
Reserving 160k for malloc() at: 87f88000
Reserving 44 Bytes for Board Info at: 87f87fd4
Reserving 36 Bytes for Global Data at: 87f87fb0
Reserving 128k for boot params() at: 87f67fb0
Stack Pointer at: 87f67f98
Now running in RAM - U-Boot at: 87fb0000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x17
flash size 8MB, sector count = 128
Flash:  8 MB
Power up PLL with outdiv = 0 then switch to 3
In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200 
athr_mgmt_init ::done
Dragonfly  ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x40802100
Trying eth0
eth0 link down
FAIL
Using eth0 device
listen from server 192.168.1.10; our IP address is 192.168.1.1
monitor_packet_result 0
Hit any key to stop autoboot:  0 
## Booting image at 9f080040 ...
   Image Name:   MIPS OpenWrt Linux-4.14.105
   Created:      2019-03-13  17:14:02 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1615472 Bytes =  1.5 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum at 0x9f080080 ...OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728

Starting kernel ...

[    0.000000] Linux version 4.14.105 (jenkins@tofu-z77hvub18_openwrt) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r0+9537-e6d28b4fee)) #0 Wed Mar 13 17:14:02 2019
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] MIPS: machine is NEC Aterm WG1200CR
[    0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] random: get_random_bytes called from start_kernel+0x8c/0x474 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 123184K/131072K available (3779K kernel code, 149K rwdata, 912K rodata, 1232K init, 204K bss, 7888K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] CPU clock: 775.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[    0.000007] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[    0.008215] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.074760] pid_max: default: 32768 minimum: 301
[    0.079783] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.086764] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.097654] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.108047] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.114544] pinctrl core: initialized pinctrl subsystem
[    0.120867] NET: Registered protocol family 16
[    0.131277] PCI host bridge /ahb/apb/pcie-controller@18250000 ranges:
[    0.138077]  MEM 0x0000000012000000..0x0000000013ffffff
[    0.143610]   IO 0x0000000000000000..0x0000000000000000
[    0.164196] PCI host bridge to bus 0000:00
[    0.168525] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[    0.175802] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.181671] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.188827] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.197596] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[    0.207577] clocksource: Switched to clocksource MIPS
[    0.213804] NET: Registered protocol family 2
[    0.219068] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.226424] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.233172] TCP: Hash tables configured (established 1024 bind 1024)
[    0.239999] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.246163] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.253036] NET: Registered protocol family 1
[    0.260391] Crashlog allocated RAM at address 0x3f00000
[    0.266999] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.277860] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.284004] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.302195] io scheduler noop registered
[    0.306326] io scheduler deadline registered (default)
[    0.313452] pinctrl-single 1804002c.pinmux: 544 pins at pa b804002c size 68
[    0.321751] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.329101] console [ttyS0] disabled
[    0.332902] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 8, base_baud = 1562500) is a 16550A
[    0.342032] console [ttyS0] enabled
[    0.342032] console [ttyS0] enabled
[    0.349582] bootconsole [early0] disabled
[    0.349582] bootconsole [early0] disabled
[    0.363588] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    0.368723] 7 fixed-partitions partitions found on MTD device spi0.0
[    0.375279] Creating 7 MTD partitions on "spi0.0":
[    0.380249] 0x000000000000-0x000000040000 : "u-boot"
[    0.386055] 0x000000040000-0x000000050000 : "u-boot-env"
[    0.392231] 0x000000050000-0x000000060000 : "devconf"
[    0.398130] 0x000000060000-0x000000070000 : "misc"
[    0.403683] 0x000000070000-0x000000080000 : "wifimngdata"
[    0.409954] 0x000000080000-0x0000007f0000 : "firmware"
[    0.416207] 2 seama-fw partitions found on MTD device firmware
[    0.422277] Creating 2 MTD partitions on "firmware":
[    0.427416] 0x000000000040-0x000000190000 : "kernel"
[    0.433161] 0x000000190000-0x000000770000 : "rootfs"
[    0.438924] mtd: device 7 (rootfs) set to be root filesystem
[    0.444806] 1 squashfs-split partitions found on MTD device rootfs
[    0.451235] 0x000000410000-0x000000770000 : "rootfs_data"
[    0.457428] 0x0000007f0000-0x000000800000 : "art"
[    0.463938] libphy: Fixed MDIO Bus: probed
[    0.807938] libphy: ag71xx_mdio: probed
[    0.814908] switch0: Atheros AR8337 rev. 2 switch registered on mdio-bus.0
[    1.469348] ag71xx 19000000.eth: invalid MAC address, using random address
[    1.808736] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[    1.820327] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
[    1.828446] NET: Registered protocol family 10
[    1.836389] Segment Routing with IPv6
[    1.840310] NET: Registered protocol family 17
[    1.844943] 8021q: 802.1Q VLAN Support v1.8
[    1.854680] VFS: Mounted root (squashfs filesystem) readonly on device 31:7.
[    1.868869] Freeing unused kernel memory: 1232K
[    1.873551] This architecture does not have kernel memory protection.
[    2.520873] init: Console is alive
[    2.524572] init: - watchdog -
[    2.547589] random: fast init done
[    3.559875] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.672369] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.690250] init: - preinit -
[    4.342977] random: jshn: uninitialized urandom read (4 bytes read)
[    4.438282] random: jshn: uninitialized urandom read (4 bytes read)
[    4.731136] random: jshn: uninitialized urandom read (4 bytes read)
[    5.812413] urandom_read: 4 callbacks suppressed
[    5.812420] random: procd: uninitialized urandom read (4 bytes read)
[    5.828955] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    5.835036] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    6.908954] eth0: link up (1000Mbps/Full duplex)
[    6.913811] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    6.920616] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[    9.041438] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[    9.069225] urandom-seed: Seed file not found (/etc/urandom.seed)
[    9.146253] eth0: link down
[    9.164727] procd: - early -
[    9.168571] procd: - watchdog -
[    9.772570] procd: - watchdog -
[    9.776058] procd: - ubus -
[    9.806263] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.829662] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.837391] procd: - init -
Please press Enter to activate this console.
[   10.109815] kmodloader: loading kernel modules from /etc/modules.d/*
[   10.121855] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.135151] Loading modules backported from Linux version v4.19.23-0-g67d52fae61c1
[   10.143016] Backport generated by backports.git v4.19.23-1-0-g480a925a
[   10.152281] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.164807] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   10.220111] xt_time: kernel timezone is -0000
[   10.273835] PPP generic driver version 2.4.2
[   10.280431] NET: Registered protocol family 24
[   10.311894] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x56.
[   10.321293] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   10.327446] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[   10.519504] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:00:00.0.txt failed with error -2
[   10.530407] ath10k_pci 0000:00:00.0: Falling back to user helper
[   10.681152] firmware ath10k!fwcfg-pci-0000:00:00.0.txt: firmware_loading_store: map pages failed
[   10.690516] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
[   10.701599] ath10k_pci 0000:00:00.0: Falling back to user helper
[   11.007662] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9888/hw2.0/ct-firmware-5.bin failed with error -2
[   11.019002] ath10k_pci 0000:00:00.0: Falling back to user helper
[   11.151281] firmware ath10k!QCA9888!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[   11.161105] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9888/hw2.0/ct-firmware-2.bin failed with error -2
[   11.172457] ath10k_pci 0000:00:00.0: Falling back to user helper
[   11.346084] firmware ath10k!QCA9888!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[   11.355906] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9888/hw2.0/firmware-6.bin failed with error -2
[   11.366987] ath10k_pci 0000:00:00.0: Falling back to user helper
[   11.540529] firmware ath10k!QCA9888!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[   12.133436] ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
[   12.142996] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   12.162949] ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9888-fW-012-38a5514c api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT crc32 2a31e1c4
[   12.497483] ath10k_pci 0000:00:00.0: board_file api 2 bmi_id 0:18 crc32 d65c17b1
[   14.534673] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   14.542446] ath10k_pci 0000:00:00.0: msdu-desc: 2500  skid: 32
[   14.572900] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   14.584209] ath10k_pci 0000:00:00.0: wmi print 'free: 121744 iram: 25908 sram: 30092'
[   14.795616] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[   14.967346] ath9k 18100000.wmac: Direct firmware load for ath9k-eeprom-ahb-18100000.wmac.bin failed with error -2
[   14.977998] ath9k 18100000.wmac: Falling back to user helper
[   15.638153] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=2
[   15.669357] kmodloader: done loading kernel modules from /etc/modules.d/*
[   23.345884] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   23.386281] jffs2_build_filesystem(): unlocking the mtd device... 
[   23.386289] done.
[   23.394701] jffs2_build_filesystem(): erasing all blocks after the end marker... 
[   27.811454] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   27.879284] device eth0 entered promiscuous mode
[   27.897902] br-lan: port 1(eth0.1) entered blocking state
[   27.903483] br-lan: port 1(eth0.1) entered disabled state
[   27.909370] device eth0.1 entered promiscuous mode
[   28.001388] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   28.078789] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   28.829239] eth0: link up (1000Mbps/Full duplex)
[   28.834089] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   28.918449] br-lan: port 1(eth0.1) entered blocking state
[   28.924038] br-lan: port 1(eth0.1) entered forwarding state
[   28.930093] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   29.077660] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   43.297671] done.
[   43.299695] jffs2: notice: (1248) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   43.749646] overlayfs: upper fs does not support tmpfile.
[  120.177615] random: crng init done



BusyBox v1.30.1 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r0+9611-6087c7b9da
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#
広告

コメントを残す

以下に詳細を記入するか、アイコンをクリックしてログインしてください。

WordPress.com ロゴ

WordPress.com アカウントを使ってコメントしています。 ログアウト /  変更 )

Google フォト

Google アカウントを使ってコメントしています。 ログアウト /  変更 )

Twitter 画像

Twitter アカウントを使ってコメントしています。 ログアウト /  変更 )

Facebook の写真

Facebook アカウントを使ってコメントしています。 ログアウト /  変更 )

%s と連携中