WN-DX1167R stock -> OpenWrt(仮)

とりあえずmkimageの改造は無しで、手元で必要なuImageの改造を加えて投げ込んだのでメモ。
Z-Loaderのブート自体にはuImageのMagicは標準の 27051956 で、uImageのイメージ名は適当なもので問題ないが、メーカーファームのWebUIから投入する際はこの2つともチェックされるのか、どちらとも変更しなければイメージのチェックをパスできなかった。
uImage参考: https://mao.5ch.net/test/read.cgi/network/1520576652/672

なお、WebUIから投入した場合、ブート中のイメージとは別のもう一方のOSイメージ用パーティションに書き込まれ、ブートパーティションの指定をそちらに変更の上リブートされて書き込まれたパーティションからブートしていた。
このブートパーティションの指定は以下の様にして書き込める。書き込み先のパーティションは、/proc/mtdを参照して “persist” パーティションのmtdblockを確認しておくこと。echo内の数字は、1つ目のOSイメージを指定する場合 “01” または “1” を、2番目を指定する場合は “02” または “2” にする。

echo -ne "\x01" | dd of=/dev/mtdblock8 bs=1 count=1 seek=4 conv=notrunc

また、上記の通りファームウェアが書き込まれブートに使用されるパーティションが固定ではないためinitramfsイメージを使用したfactoryになる。投入した際に2番目のOSイメージパーティションに書き込まれそちらからブートした場合、非initramfsなファームをsysupgradeで書き込む前に1番目のOSイメージからブートするよう指定しておく必要がある。

[  942.544000] led=9, on=1, off=1, blinks,=1, reset=0, time=4000 low_trigger=0
Unlocking firmware_2 ...

Writing from /tmp/fw.bin to firmware_2 ...     
Header checksum OK.
Data checksum OK
Unlocking persist ...
### Switch to bank 2 on next boot! ###
procd: - shutdown -
[  948.224000] br-lan: port 4(ra0) entered disabled state
[  948.232000] br-lan: port 3(rai0) entered disabled state
[  948.244000] br-lan: port 2(eth1) entered disabled state
[  948.256000] br-lan: port 1(eth0) entered disabled state
[  948.264000] device eth0 left promiscuous mode
[  948.276000] br-lan: port 1(eth0) entered disabled state
[  948.284000] ra2880stop()...Done
[  948.292000] eth1: ===> VirtualIF_close
[  948.300000] Free TX/RX Ring Memory!
[  948.308000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[  948.320000] device eth1 left promiscuous mode
[  948.332000] br-lan: port 2(eth1) entered disabled state
[  948.340000] eth1: ===> VirtualIF_close
[  948.348000] device ra0 left promiscuous mode
[  948.360000] br-lan: port 4(ra0) entered disabled state
[  948.368000] device rai0 left promiscuous mode
[  948.376000] br-lan: port 3(rai0) entered disabled state
[  949.700000] WifiSysClose(), wdev idx = 0
[  949.712000] WifiSysGetBssInfoState(): BssInfoIdx 0 not found!!!
[  949.724000] WifiSysUpdateBssInfoState(): BssInfoIdx 0 not found!!!
### ap ###
[  951.176000] Device Instance
[  951.184000]  WDEV 00:
                Name:rai0
[  951.188000]          Wdev(list) Idx:0
[  951.196000]           Idx:8
[  951.200000]  WDEV 01:
                Name:rai1
[  951.208000]          Wdev(list) Idx:1
[  951.212000]           Idx:9
[  951.216000]  WDEV 02:
                Name:rai2
[  951.224000]          Wdev(list) Idx:2
[  951.228000]           Idx:10
[  951.236000]  WDEV 03:
                Name:rai3
[  951.240000]          Wdev(list) Idx:3
[  951.248000]           Idx:11
[  951.252000]  WDEV 04:
                Name:ra0
[  951.260000]          Wdev(list) Idx:4
[  951.264000]           Idx:12
[  951.268000]  WDEV 05:
                Name:ra1
[  951.276000]          Wdev(list) Idx:5
[  951.284000]           Idx:13
[  951.288000]  WDEV 06:
                Name:ra2
[  951.292000]          Wdev(list) Idx:6
[  951.300000]           Idx:14
[  951.304000]  WDEV 07:
                Name:ra3
[  951.312000]          Wdev(list) Idx:7
[  951.316000]           Idx:15
[  951.320000]  WDEV 08:
                Name:apclii0
[  951.328000]          Wdev(list) Idx:8
[  951.336000]           Idx:16
[  951.340000]  WDEV 09:
                Name:apcli0
[  951.348000]          Wdev(list) Idx:9
[  951.352000]           Idx:17
[  951.356000]  WDEV 10:
[  951.360000]  WDEV 11:
[  951.368000]  WDEV 12:
[  951.372000]  WDEV 13:
[  951.376000]  WDEV 14:
[  951.380000]  WDEV 15:
[  951.384000]  WDEV 16:
[  951.388000]  WDEV 17:
[  951.396000] WifiSysClose(), wdev idx = 4
[  951.396000] WifiSysGetBssInfoState(): BssInfoIdx 1 not found!!!
[  951.396000] WifiSysUpdateBssInfoState(): BssInfoIdx 1 not found!!!
[  951.432000] MtAsicSetPiggyBack(779): Not support for HIF_MT yet!
[  951.444000] WifiSysClose(), wdev idx = 0
[  951.452000] WifiSysClose(), wdev idx = 1
[  951.460000] WifiSysClose(), wdev idx = 2
[  951.464000] WifiSysClose(), wdev idx = 3
[  951.500000] MtAsicSetPiggyBack(779): Not support for HIF_MT yet!
[  951.512000] WifiSysClose(), wdev idx = 4
[  951.520000] WifiSysClose(), wdev idx = 5
[  951.528000] WifiSysClose(), wdev idx = 6
[  951.536000] WifiSysClose(), wdev idx = 7
[  951.544000] kill LoopBackTxTask task failed!
[  951.560000] AndesRestartCheck: Current TOP_MISC2(0x7)
[  951.612000] CmdReStartDLRsp: Status Success!, Status(0)
[  951.624000] EventExtEventHandler: Unknown Ext Event(6f)
[  951.632000] AndesRestartCheck:  TOP_MISC2(1)
[  951.644000] RT28xxPciAsicRadioOff(): Not support for HIF_MT yet!
[  951.656000] RTMPDrvClose call RT28xxPciAsicRadioOff fail !!
[  951.664000] tx_kickout_fail_count = 0
[  951.672000] tx_timeout_fail_count = 0
[  951.680000] rx_receive_fail_count = 0
[  951.688000] alloc_cmd_msg = 3185
[  951.692000] free_cmd_msg = 3185
[  951.700000] cut_through_token_list_destroy(): 8632e888,8632e888
[  951.716000] cut_through_token_list_destroy(): 8632e898,8632e898
[  951.732000] FwOwn()::Set Fw Own
[  951.740000] RTMP_AllTimerListRelease: Size=0
[  951.748000] FwOwn()::Return since already in Fw Own...
[  951.760000] <---HwCtrlThread
procd: - reboot [  951.896000] Stopped WatchDog Timer.
-
[  951.908000] Restarting system.


U-Boot 1.1.3 (Aug  6 2018 - 14:37:41)

Board: Ralink APSoC DRAM:  128 MB
relocate_code Pointer at: 87f98000

Config XHCI 40M PLL 
******************************
Software System Reset Occurred
******************************
Allocate 16 byte aligned buffer: 87fcb030
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [01 F1 80 1D 01]
Device found in MTK table, ID: 1f1, EXT_ID: 801d01
Support this Device in MTK table! 1f1 
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 1023
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64,    mtd->erasesize=131072  devinfo.iowidth=8
....============================================ 
Ralink UBoot Version: 5.0.0.0
-------------------------------------------- 
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection 
DRAM_TYPE: DDR3 
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: NAND Flash
Date:Aug  6 2018  Time:14:37:41
============================================ 
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768 

 ##### The CPU freq = 880 MHZ #### 
 estimate memory size =128 Mbytes
#Reset_MT7530
set LAN/WAN WLLLL
.## Starting application at 0x81E00000 ...


Z-LOADER V1.28 | 08/06/2018 14:37:44


..Hit ESC key to stop autoboot: 1

Checking image 2...
   Image Name:   3.10(XIK.1)b7
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    5642895 Bytes =  5.4 MB
   Load Address: 80001000
   Entry Point:  80001000
.......................................................................................   Verifying Combo Checksum ... .......................................................................................## Booting image at bf700000 ...
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 128

Starting kernel ...

[    0.000000] Linux version 4.14.111 (musashino205@Taiha.Net) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r0+9824-b80243858e)) #0 SMP Wed Apr 17 15:36:46 2019
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] MIPS: machine is I-O DATA WN-DX1167R
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] VPE topology {2,2} total 4
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] random: get_random_bytes called from start_kernel+0x90/0x4a4 with crng_init=0
[    0.000000] percpu: Embedded 14 pages/cpu @81110000 s26192 r8192 d22960 u57344
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00001000
[    0.000000] Readback ErrCtl register=00001000
[    0.000000] Memory: 119764K/131072K available (4497K kernel code, 230K rwdata, 1000K rodata, 3860K init, 248K bss, 11308K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 880MHz
[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[    0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[    0.015488] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[    0.087817] pid_max: default: 32768 minimum: 301
[    0.097128] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.110148] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.125865] Hierarchical SRCU implementation.
[    0.135322] smp: Bringing up secondary CPUs ...
[    0.144860] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.144869] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.144880] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.145014] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.204698] Synchronize counters for CPU 1: done.
[    0.268616] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.268624] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.268631] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.268708] CPU2 revision is: 0001992f (MIPS 1004Kc)
[    0.325524] Synchronize counters for CPU 2: done.
[    0.385686] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.385694] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.385702] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.385788] CPU3 revision is: 0001992f (MIPS 1004Kc)
[    0.445092] Synchronize counters for CPU 3: done.
[    0.504696] smp: Brought up 1 node, 4 CPUs
[    0.516465] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.535934] futex hash table entries: 1024 (order: 3, 32768 bytes)
[    0.548360] pinctrl core: initialized pinctrl subsystem
[    0.559927] NET: Registered protocol family 16
[    0.577592] pull PCIe RST: RALINK_RSTCTRL = 4000000
[    0.887578] release PCIe RST: RALINK_RSTCTRL = 7000000
[    0.897642] ***** Xtal 40MHz *****
[    0.904375] release PCIe RST: RALINK_RSTCTRL = 7000000
[    0.914578] Port 0 N_FTS = 1b102800
[    0.921480] Port 1 N_FTS = 1b105000
[    0.928405] Port 2 N_FTS = 1b102800
[    2.087057] PCIE0 no card, disable it(RST&CLK)
[    2.095745] PCIE2 no card, disable it(RST&CLK)
[    2.104548]  -> 20107f2
[    2.109398] PCIE1 enabled
[    2.114577] PCI host bridge /pcie@1e140000 ranges:
[    2.124105]  MEM 0x0000000060000000..0x000000006fffffff
[    2.134461]   IO 0x000000001e160000..0x000000001e16ffff
[    2.144829] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
[    2.167715] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    2.179008] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    2.190256] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    2.202750] PCI host bridge to bus 0000:00
[    2.210765] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    2.224420] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    2.236168] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    2.249643] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    2.266495] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    2.279517] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.293336] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    2.306817] pci 0000:00:00.0: BAR 1: assigned [mem 0x60100000-0x6010ffff]
[    2.320308] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[    2.334821] pci 0000:00:00.0: PCI bridge to [bus 01]
[    2.344646] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    2.359432] clocksource: Switched to clocksource GIC
[    2.370675] NET: Registered protocol family 2
[    2.379985] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    2.393721] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    2.406321] TCP: Hash tables configured (established 1024 bind 1024)
[    2.419053] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    2.430556] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    2.443200] NET: Registered protocol family 1
[    5.829397] 4 CPUs re-calibrate udelay(lpj = 2924544)
[    5.840886] Crashlog allocated RAM at address 0x3f00000
[    5.851393] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    5.871370] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    5.882853] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    5.903955] random: fast init done
[    5.912889] io scheduler noop registered
[    5.920594] io scheduler deadline registered (default)
[    5.931775] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[    5.945639] console [ttyS0] disabled
[    5.952691] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A
[    5.970626] console [ttyS0] enabled
[    5.970626] console [ttyS0] enabled
[    5.984418] bootconsole [early0] disabled
[    5.984418] bootconsole [early0] disabled
[    6.000996] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    6.013896] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[    6.027937] Enable NFI Clock
[    6.033683] # MTK NAND # : Use HW ECC
[    6.040994] Device found in MTK table, ID: 1f1, EXT_ID: 801d01
[    6.052607] Support this Device in MTK table! 1f1 
[    6.062329] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[    6.075199] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
[    6.087848] nand: AMD/Spansion NAND 128MiB 3,3V 8-bit
[    6.097905] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    6.112993] Scanning device for bad blocks
[    6.402781] 11 fixed-partitions partitions found on MTD device MT7621-NAND
[    6.416469] Creating 11 MTD partitions on "MT7621-NAND":
[    6.427064] 0x000000000000-0x000000100000 : "Bootloader"
[    6.438719] 0x000000100000-0x000000200000 : "u-boot-env"
[    6.450391] 0x000000200000-0x000000300000 : "Factory"
[    6.461506] 0x000000300000-0x000000400000 : "SecondBoot"
[    6.473133] 0x000000400000-0x000003600000 : "firmware"
[    6.484786] 0x000003600000-0x000003700000 : "Config"
[    6.495732] 0x000003700000-0x000006900000 : "firmware_2"
[    6.507770] 0x000006900000-0x000006a00000 : "Config_2"
[    6.519064] 0x000006a00000-0x000006b00000 : "persist"
[    6.530220] 0x000006b00000-0x000006c00000 : "idmkey"
[    6.541165] 0x000006c00000-0x000007f80000 : "Backup"
[    6.552232] [mtk_nand] probe successfully!
[    6.561139] Signature matched and data read!
[    6.569641] load_fact_bbt success 1023
[    6.577863] libphy: Fixed MDIO Bus: probed
[    6.652008] libphy: mdio: probed
[    8.069445] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[    8.082014] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 19
[    8.100784] NET: Registered protocol family 10
[    8.110937] Segment Routing with IPv6
[    8.118291] NET: Registered protocol family 17
[    8.127200] 8021q: 802.1Q VLAN Support v1.8
[    8.137882] hctosys: unable to open rtc device (rtc0)
[    8.162308] Freeing unused kernel memory: 3860K
[    8.171369] This architecture does not have kernel memory protection.
[    8.195375] init: Console is alive
[    8.202430] init: - watchdog -
[    8.220365] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    8.237385] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    8.259728] init: - preinit -
[    8.426327] mtk_soc_eth 1e100000.ethernet: PPE started
[    8.448840] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.299905] mtk_soc_eth 1e100000.ethernet eth0: port 0 link up
[    9.668050] mtk_soc_eth 1e100000.ethernet eth0: port 2 link up
[   11.563105] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
[   11.584512] procd: - early -
[   11.590391] procd: - watchdog -
[   12.219565] procd: - watchdog -
[   12.226120] procd: - ubus -
[   12.236341] random: ubusd: uninitialized urandom read (4 bytes read)
[   12.289976] random: ubusd: uninitialized urandom read (4 bytes read)
[   12.303033] random: ubusd: uninitialized urandom read (4 bytes read)
[   12.316534] procd: - init -
Please press Enter to activate this console.
[   12.475962] kmodloader: loading kernel modules from /etc/modules.d/*
[   12.494539] nat46: module (version 683fbd2b765506332a1af141545652bf58f03166) loaded.
[   12.514229] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   12.533949] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.556171] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   12.600620] Netfilter messages via NETLINK v0.30.
[   12.632397] xt_time: kernel timezone is -0000
[   12.648384] ctnetlink v0.93: registering with nfnetlink.
[   12.661713] PPP generic driver version 2.4.2
[   12.671586] NET: Registered protocol family 24
[   12.684076] kmodloader: done loading kernel modules from /etc/modules.d/*
[   13.773293] urandom_read: 5 callbacks suppressed
[   13.773305] random: jshn: uninitialized urandom read (4 bytes read)
[   52.550164] mtk_soc_eth 1e100000.ethernet: PPE started
[   52.569852] br-lan: port 1(eth0.1) entered blocking state
[   52.580768] br-lan: port 1(eth0.1) entered disabled state
[   52.592245] device eth0.1 entered promiscuous mode
[   52.601899] device eth0 entered promiscuous mode
[   52.615251] br-lan: port 1(eth0.1) entered blocking state
[   52.626114] br-lan: port 1(eth0.1) entered forwarding state
[   52.637820] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   53.045858] random: crng init done
[   53.550050] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready



BusyBox v1.30.1 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r0+9891-163a8830b9
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# 
広告

コメントを残す

以下に詳細を記入するか、アイコンをクリックしてログインしてください。

WordPress.com ロゴ

WordPress.com アカウントを使ってコメントしています。 ログアウト /  変更 )

Google フォト

Google アカウントを使ってコメントしています。 ログアウト /  変更 )

Twitter 画像

Twitter アカウントを使ってコメントしています。 ログアウト /  変更 )

Facebook の写真

Facebook アカウントを使ってコメントしています。 ログアウト /  変更 )

%s と連携中