WRC-733GHBK ブート時TFTP (RESETボタン)

WRC-733GHBKは、デバイスの電源投入時にRESETボタンを押しながら行うとTFTPサーバが開始される。
その時投入してみたログ。

U-Boot 1.1.3 (Jun  2 2015 - 17:05:47)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29 
spi device id: c2 20 17 c2 20 (2017c220)
find flash: MX25L6405D
raspi_read: from:30000 len:1000 
*** Warning - bad CRC, using default environment

============================================ 
Ralink UBoot Version: 4.1.2.0
-------------------------------------------- 
ASIC 7620_MP (Port5GigaSW)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jun  2 2015  Time:17:05:47
============================================ 
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768 

 ##### The CPU freq = 580 MHZ #### 
 estimate memory size =64 Mbytes

 Realtek giga Mac init!

 Realtek giga Mac done!

Please choose the operation: 
   1: Load system code to SDRAM via TFTP. 
   2: Load system code then write to Flash via TFTP. 
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   5: Load ucos code to SDRAM via TFTP Client. 
   7: Load Boot Loader code then write to Flash via Serial. 
   9: Load Boot Loader code then write to Flash via TFTP. 

raspi_read: from:40028 len:6 

   
5: System Load Boot Loader | F/W  then write to Flash via TFTP Client. 
 Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
 Please Input new ones /or Ctrl-C to discard
        Input device IP (192.168.2.81)  Input server IP (192.168.2.89)  Input Linux Kernel filename () 
 netboot_common, argc= 3 

 NetTxPacket = 0x83FE3E80 

 KSEG1ADDR(NetTxPacket) = 0xA3FE3E80 

 NetLoop,call eth_halt ! 

 NetLoop,call eth_init ! 
Trying Eth0 (10/100-M)

 Waitting for RX_DMA_BUSY status Start... done


 Realtek giga Mac init!
regData1 = 0000 regData2 = 0000, RTL8367R
(rtk_switch_init 11983) init_rgmii done 

 Realtek giga Mac support done

 ETH_STATE_ACTIVE!! 
(NetLoop 408) bd->bi_enetaddr = 00:00:aa:bb:cc:dd
(NetLoop 409) NetOurEther = 00:00:aa:bb:cc:dd
Select server or client model: 1/2
server model start
SERVER IP address : 192.168.1.6 port:69
Load address: 0x80a00000
Loading: checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
Got ARP REQUEST, return our IP
Peer IP:192.168.1.89
Got ARP REPLY, set server/gtwy eth addr (3c:97:0e:60:44:30)
Got it
Peer IP:192.168.1.89
#################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ######################
done
Bytes transferred = 5767953 (580311 hex)
NetBootFileXferSize= 00580311

****************Parse Head**************
signature=CSYS startAddr=0x01100000 burnAddr=0x00070000 nmodTag=RN62 len=0x0057ac72 

****************CheckSume**************
CheckSum ok!
****************Start Upgrade Kernel**************
raspi_erase_write: offs:70000, count:57ac86
raspi_erase: offs:70000 len:570000
.......................................................................................
raspi_write: to:70000 len:570000 
.......................................................................................
raspi_read: from:70000 len:10000 
raspi_read: from:80000 len:10000 
raspi_read: from:90000 len:10000 
raspi_read: from:a0000 len:10000 
raspi_read: from:b0000 len:10000 
raspi_read: from:c0000 len:10000 
raspi_read: from:d0000 len:10000 
raspi_read: from:e0000 len:10000 
raspi_read: from:f0000 len:10000 
raspi_read: from:100000 len:10000 
raspi_read: from:110000 len:10000 
raspi_read: from:120000 len:10000 
raspi_read: from:130000 len:10000 
raspi_read: from:140000 len:10000 
raspi_read: from:150000 len:10000 
raspi_read: from:160000 len:10000 
raspi_read: from:170000 len:10000 
raspi_read: from:180000 len:10000 
raspi_read: from:190000 len:10000 
raspi_read: from:1a0000 len:10000 
raspi_read: from:1b0000 len:10000 
raspi_read: from:1c0000 len:10000 
raspi_read: from:1d0000 len:10000 
raspi_read: from:1e0000 len:10000 
raspi_read: from:1f0000 len:10000 
raspi_read: from:200000 len:10000 
raspi_read: from:210000 len:10000 
raspi_read: from:220000 len:10000 
raspi_read: from:230000 len:10000 
raspi_read: from:240000 len:10000 
raspi_read: from:250000 len:10000 
raspi_read: from:260000 len:10000 
raspi_read: from:270000 len:10000 
raspi_read: from:280000 len:10000 
raspi_read: from:290000 len:10000 
raspi_read: from:2a0000 len:10000 
raspi_read: from:2b0000 len:10000 
raspi_read: from:2c0000 len:10000 
raspi_read: from:2d0000 len:10000 
raspi_read: from:2e0000 len:10000 
raspi_read: from:2f0000 len:10000 
raspi_read: from:300000 len:10000 
raspi_read: from:310000 len:10000 
raspi_read: from:320000 len:10000 
raspi_read: from:330000 len:10000 
raspi_read: from:340000 len:10000 
raspi_read: from:350000 len:10000 
raspi_read: from:360000 len:10000 
raspi_read: from:370000 len:10000 
raspi_read: from:380000 len:10000 
raspi_read: from:390000 len:10000 
raspi_read: from:3a0000 len:10000 
raspi_read: from:3b0000 len:10000 
raspi_read: from:3c0000 len:10000 
raspi_read: from:3d0000 len:10000 
raspi_read: from:3e0000 len:10000 
raspi_read: from:3f0000 len:10000 
raspi_read: from:400000 len:10000 
raspi_read: from:410000 len:10000 
raspi_read: from:420000 len:10000 
raspi_read: from:430000 len:10000 
raspi_read: from:440000 len:10000 
raspi_read: from:450000 len:10000 
raspi_read: from:460000 len:10000 
raspi_read: from:470000 len:10000 
raspi_read: from:480000 len:10000 
raspi_read: from:490000 len:10000 
raspi_read: from:4a0000 len:10000 
raspi_read: from:4b0000 len:10000 
raspi_read: from:4c0000 len:10000 
raspi_read: from:4d0000 len:10000 
raspi_read: from:4e0000 len:10000 
raspi_read: from:4f0000 len:10000 
raspi_read: from:500000 len:10000 
raspi_read: from:510000 len:10000 
raspi_read: from:520000 len:10000 
raspi_read: from:530000 len:10000 
raspi_read: from:540000 len:10000 
raspi_read: from:550000 len:10000 
raspi_read: from:560000 len:10000 
raspi_read: from:570000 len:10000 
raspi_read: from:580000 len:10000 
raspi_read: from:590000 len:10000 
raspi_read: from:5a0000 len:10000 
raspi_read: from:5b0000 len:10000 
raspi_read: from:5c0000 len:10000 
raspi_read: from:5d0000 len:10000 
raspi_read: from:5e0000 len:10000 
raspi_erase: offs:5e0000 len:10000
.
raspi_write: to:5e0000 len:10000 
.
raspi_read: from:5e0000 len:10000 
Done!
## Booting image at bc070000 ...
raspi_read: from:70000 len:40 
Magic number at 0xBC070000 
   Image Name:   MIPS OpenWrt Linux-4.14.138
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1670238 Bytes =  1.6 MB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:70054 len:197c5e 
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 4.14.138 (musashino205@Taiha.Net) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r0+10854-852f048b82)) #0 Fri Aug 23 16:55:26 2019
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is ELECOM WRC-733GHBK
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] random: get_random_bytes called from start_kernel+0x98/0x4a0 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16240
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=0007fabe
[    0.000000] Readback ErrCtl register=0007fabe
[    0.000000] Memory: 58360K/65536K available (3917K kernel code, 190K rwdata, 892K rodata, 1200K init, 213K bss, 7176K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 580MHz
[    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[    0.000000] systick: enable autosleep mode
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[    0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[    0.015467] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.087707] pid_max: default: 32768 minimum: 301
[    0.097160] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.110182] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.131221] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.150708] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.162924] pinctrl core: initialized pinctrl subsystem
[    0.173787] NET: Registered protocol family 16
[    0.665950] PCI host bridge /pcie@10140000 ranges:
[    0.675350]  MEM 0x0000000020000000..0x000000002fffffff
[    0.685722]   IO 0x0000000010160000..0x000000001016ffff
[    0.714206] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.725244] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.737497] GPIO line 0 (rtl8367rb-reset) hogged as output/high
[    0.750035] PCI host bridge to bus 0000:00
[    0.758035] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    0.771751] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    0.783477] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.796976] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.813215] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.830199] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    0.843254] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    0.857062] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
[    0.870562] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[    0.884071] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]
[    0.897568] pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff]
[    0.911066] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.920917] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x201fffff]
[    0.938629] clocksource: Switched to clocksource systick
[    0.950480] NET: Registered protocol family 2
[    0.959938] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.973721] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.986303] TCP: Hash tables configured (established 1024 bind 1024)
[    0.999087] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.010614] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    1.023350] NET: Registered protocol family 1
[    1.035064] rt-timer 10000100.timer: maximum frequency is 1220Hz
[    1.047873] Crashlog allocated RAM at address 0x3f00000
[    1.060080] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[    1.080014] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.091518] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    1.124159] io scheduler noop registered
[    1.131868] io scheduler deadline registered (default)
[    1.142881] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    1.156522] console [ttyS0] disabled
[    1.163578] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[    1.183243] console [ttyS0] enabled
[    1.183243] console [ttyS0] enabled
[    1.197059] bootconsole [early0] disabled
[    1.197059] bootconsole [early0] disabled
[    1.213531] cacheinfo: Failed to find cpu0 device node
[    1.223811] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    1.241020] spi spi0.0: force spi mode3
[    1.249524] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    1.259355] 6 fixed-partitions partitions found on MTD device spi0.0
[    1.272021] Creating 6 MTD partitions on "spi0.0":
[    1.281598] 0x000000000000-0x000000030000 : "u-boot"
[    1.292477] 0x000000030000-0x000000040000 : "u-boot-env"
[    1.304022] 0x000000040000-0x000000050000 : "factory"
[    1.315022] 0x000000050000-0x000000070000 : "nvram"
[    1.325661] 0x000000070000-0x0000007f0000 : "firmware"
[    1.340588] 2 edimax-fw partitions found on MTD device firmware
[    1.352442] Creating 2 MTD partitions on "firmware":
[    1.362354] 0x000000000000-0x000000197cb2 : "kernel"
[    1.373202] 0x000000197cb2-0x000000780000 : "rootfs"
[    1.383991] mtd: device 6 (rootfs) set to be root filesystem
[    1.396927] 1 squashfs-split partitions found on MTD device rootfs
[    1.409321] 0x00000057b000-0x000000780000 : "rootfs_data"
[    1.421034] 0x0000007f0000-0x000000800000 : "hwconfig"
[    1.433043] libphy: Fixed MDIO Bus: probed
[    1.451060] gsw: setting port4 to ephy mode
[    1.459500] mtk_soc_eth 10100000.ethernet: generated random MAC address 62:be:ad:3f:f9:38
[    1.475838] mtk_soc_eth 10100000.ethernet: using fixed link parameters
[    1.488931] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[    1.501443] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    1.518465] rt2880_wdt 10000120.watchdog: Initialized
[    1.529931] NET: Registered protocol family 10
[    1.542959] Segment Routing with IPv6
[    1.550459] NET: Registered protocol family 17
[    1.559409] 8021q: 802.1Q VLAN Support v1.8
[    1.578909] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[    1.599546] Freeing unused kernel memory: 1200K
[    1.608595] This architecture does not have kernel memory protection.
[    2.623338] init: Console is alive
[    2.630457] init: - watchdog -
[    2.798590] random: fast init done
[    3.878900] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.104077] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.121329] init: - preinit -
[    5.573772] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
[    5.590196] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3[    5.753384] random: procd: uninitialized urandom read (4 bytes read)
] or [4] key and hit [enter] to select the debug level
[    6.316998] mount_root: no usable overlay filesystem found, using tmpfs overlay
[    6.364486] urandom-seed: Seed file not found (/etc/urandom.seed)
[    6.461068] mtk_soc_eth 10100000.ethernet eth0: port 5 link down
[    6.485387] procd: - early -
[    6.491235] procd: - watchdog -
[    6.698076] procd: - watchdog -
[    6.704756] procd: - ubus -
[    6.862689] random: ubusd: uninitialized urandom read (4 bytes read)
[    6.981070] random: ubusd: uninitialized urandom read (4 bytes read)
[    6.994384] random: ubusd: uninitialized urandom read (4 bytes read)
[    7.008207] procd: - init -
Please press Enter to activate this console.
[    7.922544] urandom_read: 5 callbacks suppressed
[    7.922555] random: jshn: uninitialized urandom read (4 bytes read)
[    8.361984] kmodloader: loading kernel modules from /etc/modules.d/*
[    8.541834] urngd: jent-rng init failed, err: 2
[    8.652330] nat46: module (version 683fbd2b765506332a1af141545652bf58f03166) loaded.
[    8.675599] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    8.697423] rtl8367b rtl8367rb: cannot find mdio node phandle
[    8.708988] rtl8367b rtl8367rb: using GPIO pins 22 (SDA) and 23 (SCK)
[    8.722970] rtl8367b rtl8367rb: RTL8367RB chip found
[    9.966115] libphy: rtl8367rb: probed
[   10.083435] Loading modules backported from Linux version v5.3-rc4-0-gd45331b00ddb
[   10.098595] Backport generated by backports.git v5.3-rc4-1-0-g4ec72687
[   10.115153] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.136997] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[   10.230487] xt_time: kernel timezone is -0000
[   10.404182] PPP generic driver version 2.4.2
[   10.415835] NET: Registered protocol family 24
[   10.440335] mt76x0e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
[   10.452952] mt76x0e 0000:01:00.0: ASIC revision: 76100002
[   10.466491] mt76x0e 0000:01:00.0: Firmware Version: 0.1.00
[   10.507031] mt76x0e 0000:01:00.0: EEPROM ver:01 fae:00
[   10.568137] ieee80211 phy1: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
[   10.588143] rt2800_wmac 10180000.wmac: Direct firmware load for soc_wmac.eeprom failed with error -2
[   10.606373] rt2800_wmac 10180000.wmac: Falling back to user helper
[   11.536487] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[   11.551999] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 7620 detected
[   11.602846] kmodloader: done loading kernel modules from /etc/modules.d/*
[   51.845474] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
[   51.861628] 8021q: adding VLAN 0 to HW filter on device eth0
[   51.946429] device eth0 entered promiscuous mode
[   51.997223] br-lan: port 1(eth0.1) entered blocking state
[   52.008062] br-lan: port 1(eth0.1) entered disabled state
[   52.019216] device eth0.1 entered promiscuous mode
[   52.094894] br-lan: port 1(eth0.1) entered blocking state
[   52.105723] br-lan: port 1(eth0.1) entered forwarding state
[   52.117038] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   52.873138] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   55.379325] jffs2: Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
[   55.396188] jffs2: empty_blocks 0, bad_blocks 0, c->nr_blocks 517
[   63.886220] random: crng init done



BusyBox v1.31.0 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r0+10852-a5aab6f68e
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# 

なんだかJFFS2周りがおかしいが、とりあえずこれで投入することが可能なことを確認。
JFFS2のエラーによりユーザー領域 (rootfs_data) が構築されない問題が発生するが、 firstboot 実施の上再起動することで正常に機能するようになった。

広告

コメントを残す

以下に詳細を記入するか、アイコンをクリックしてログインしてください。

WordPress.com ロゴ

WordPress.com アカウントを使ってコメントしています。 ログアウト /  変更 )

Google フォト

Google アカウントを使ってコメントしています。 ログアウト /  変更 )

Twitter 画像

Twitter アカウントを使ってコメントしています。 ログアウト /  変更 )

Facebook の写真

Facebook アカウントを使ってコメントしています。 ログアウト /  変更 )

%s と連携中