WRC-1167FS stock -> OpenWrt

とりあえずfactoryファームを正しい状態にdecodeされる形で組めたので、投入テスト。
stockで SQUASHFS error が大量に吐かれるのは何だろうか…(出ないこともあった)

------- ELECOM1701 Header Info
Image Header Size      : 0x0038
Image Header ID        : ELECOM
Image Product Name     : WRC-1167FS
Image Version          : 0.00
------------------------------
------- Header Info
Image Header Size      : 0x0074
Image Header Magic Code: 0x031d6129
Image Data Size        : 6291456
Image Type             : 0x6 [kernel_elecom1701]
Compression Type       : 0x0
Model ID               : 0x00228000
Build Date             : 1970-01-1
Version Firmware       : 
Version Code SCM       : 
Version Config         :                                 
Data CRC Checksum      : 0x337EBA50
Header CRC Checksum    : 0x0
------------------------------
FWHANDLE, DECODE PASS
Erasing blocks: 96/96 (100%)
Writing data: 6144k/6144k (100%)
Verifying data: 6144k/6144k (100%)
The system is going down NOW!
[43306.704000] SQUASHFS error: zlib_inflate error, data probably corrupt
[43306.728000] SQUASHFS error: squashfs_read_data failed to read block 0x1d6305
[43306.740000] SQUASHFS error: Unable to read fragment cache entry [1d6305]
[43306.756000] SQUASHFS error: Unable to read page, block 1d6305, size 9161
[43306.768000] SQUASHFS error: Unable to read fragment cache entry [1d6305]
[43306.780000] SQUASHFS error: Unable to read page, block 1d6305, size 9161
[43306.796000] SQUASHFS error: Unable to read fragment cache entry [1d6305]
[43306.808000] SQUASHFS error: Unable to read page, block 1d6305, size 9161
[43306.820000] SQUASHFS error: Unable to read fragment cache entry [1d6305]
[43306.836000] SQUASHFS error: Unable to read page, block 1d6305, size 9161
[43306.848000] SQUASHFS error: Unable to read fragment cache entry [1d6305]
[43306.864000] SQUASHFS error: Unable to read page, block 1d6305, size 9161
[43306.876000] SQUASHFS error: Unable to read fragment cache entry [1d6305]
[43306.888000] SQUASHFS error: Unable to read page, block 1d6305, size 9161
[43306.904000] SQUASHFS error: Unable to read fragment cache entry [1d6305]
[43306.916000] SQUASHFS error: Unable to read page, block 1d6305, size 9161
[43306.928000] SQUASHFS error: Unable to read fragment cache entry [1d6305]
[43306.944000] SQUASHFS error: Unable to read page, block 1d6305, size 9161
[43306.956000] SQUASHFS error: Unable to read fragment cache entry [1d6305]
[43306.972000] SQUASHFS error: Unable to read page, block 1d6305, size 9161
[43306.984000] SQUASHFS error: Unable to read fragment cache entry [1d6305]
[43306.996000] SQUASHFS error: Unable to read page, block 1d6305, size 9161
[43307.012000] SQUASHFS error: Unable to read fragment cache entry [1d6305]
[43307.024000] SQUASHFS error: Unable to read page, block 1d6305, size 9161
[43307.036000] SQUASHFS error: Unable to read fragment cache entry [1d6305]
[43307.052000] SQUASHFS error: Unable to read page, block 1d6305, size 9161
[43307.064000] SQUASHFS error: Unable to read fragment cache entry [1d6305]
[43307.080000] SQUASHFS error: Unable to read page, block 1d6305, size 9161
[43307.092000] SQUASHFS error: Unable to read fragment cache entry [1d6305]
[43307.104000] SQUASHFS error: Unable to read page, block 1d6305, size 9161
Sent SIGKILL to all processes
Requesting system reboot
[43308.712000] Restarting system.
[04060C09][04060C09]
DDR Calibration DQS reg = 00008787


U-Boot 1.1.3 (Oct 23 2017 - 16:14:35)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fa0000
******************************
Software System Reset Occurred
******************************
flash manufacture id: ef, device id 40 18
find flash: W25Q128BV
============================================ 
Ralink UBoot Version: 5.0.0.0
-------------------------------------------- 
ASIC 7628_MP (Port5None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Oct 23 2017  Time:16:14:35
============================================ 
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768 

 ##### The CPU freq = 580 MHZ #### 
 estimate memory size = 64 Mbytes
RESET MT7628 PHY!!!!!!
Please choose the operation: 
   1: Load system code to SDRAM via TFTP. 
   2: Load system code then write to Flash via TFTP. 
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial. 
   9: Load Boot Loader code then write to Flash via TFTP. 
default: 3                                                                                                                 0 
   
3: System Boot system code via Flash.
## Booting image at bc050000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.143
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1669570 Bytes =  1.6 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 4.14.143 (musashino205@Taiha.Net) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r0+11022-f01af852e5)) #0 Sun Sep 15 03:19:24 2019
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7628AN ver:1 eco:2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[    0.000000] MIPS: machine is ELECOM WRC-1167FS
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] random: get_random_bytes called from start_kernel+0x98/0x4a0 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16240
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=000779f0
[    0.000000] Readback ErrCtl register=000779f0
[    0.000000] Memory: 58372K/65536K available (3919K kernel code, 185K rwdata, 892K rodata, 1204K init, 206K bss, 7164K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 256
[    0.000000] intc: using register map from devicetree
[    0.000000] CPU Clock: 580MHz
[    0.000000] timer_probe: no matching timers found
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[    0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[    0.015371] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.087589] pid_max: default: 32768 minimum: 301
[    0.096986] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.109944] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.130499] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.149876] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.162027] pinctrl core: initialized pinctrl subsystem
[    0.173329] NET: Registered protocol family 16
[    0.290156] mt7620-pci 10140000.pcie: Port 0 N_FTS = 1b105000
[    0.451172] PCI host bridge /pcie@10140000 ranges:
[    0.460516]  MEM 0x0000000020000000..0x000000002fffffff
[    0.470830]   IO 0x0000000010160000..0x000000001016ffff
[    0.500056] mt7621_gpio 10000600.gpio: registering 32 gpios
[    0.511272] mt7621_gpio 10000600.gpio: registering 32 gpios
[    0.522397] mt7621_gpio 10000600.gpio: registering 32 gpios
[    0.534247] PCI host bridge to bus 0000:00
[    0.542215] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    0.555863] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    0.567501] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.580917] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.597737] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    0.610732] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    0.624454] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[    0.637870] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[    0.652146] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[    0.665570] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[    0.680026] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[    0.694282] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.704078] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
[    0.717505] pci 0000:00:00.0:   bridge window [mem 0x20100000-0x201fffff pref]
[    0.736698] clocksource: Switched to clocksource MIPS
[    0.747967] NET: Registered protocol family 2
[    0.757384] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.771089] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.783600] TCP: Hash tables configured (established 1024 bind 1024)
[    0.796304] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.807770] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.820453] NET: Registered protocol family 1
[    0.832838] Crashlog allocated RAM at address 0x3f00000
[    0.844881] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[    0.864744] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.876196] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.908291] io scheduler noop registered
[    0.915904] io scheduler deadline registered (default)
[    0.927039] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[    0.940675] console [ttyS0] disabled
[    0.947712] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
[    0.965533] console [ttyS0] enabled
[    0.965533] console [ttyS0] enabled
[    0.979266] bootconsole [early0] disabled
[    0.979266] bootconsole [early0] disabled
[    0.996371] spi-mt7621 10000b00.spi: sys_freq: 193333333
[    1.021181] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    1.030557] 5 fixed-partitions partitions found on MTD device spi0.0
[    1.043143] Creating 5 MTD partitions on "spi0.0":
[    1.052647] 0x000000000000-0x000000030000 : "u-boot"
[    1.063444] 0x000000030000-0x000000040000 : "u-boot-env"
[    1.074905] 0x000000040000-0x000000050000 : "factory"
[    1.085896] 0x000000050000-0x000000780000 : "firmware"
[    1.100090] 2 uimage-fw partitions found on MTD device firmware
[    1.111878] Creating 2 MTD partitions on "firmware":
[    1.121728] 0x000000000000-0x000000197a02 : "kernel"
[    1.132503] 0x000000197a02-0x000000730000 : "rootfs"
[    1.143221] mtd: device 5 (rootfs) set to be root filesystem
[    1.156083] 1 squashfs-split partitions found on MTD device rootfs
[    1.168396] 0x0000005f0000-0x000000730000 : "rootfs_data"
[    1.180046] 0x000000780000-0x000000800000 : "storage"
[    1.191697] libphy: Fixed MDIO Bus: probed
[    1.212238] rt3050-esw 10110000.esw: link changed 0x00
[    1.224104] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    1.242355] NET: Registered protocol family 10
[    1.255536] Segment Routing with IPv6
[    1.262985] NET: Registered protocol family 17
[    1.271879] 8021q: 802.1Q VLAN Support v1.8
[    1.286868] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    1.307441] Freeing unused kernel memory: 1204K
[    1.316404] This architecture does not have kernel memory protection.
[    1.970141] init: Console is alive
[    1.977215] init: - watchdog -
[    2.550349] random: fast init done
[    2.756372] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    2.937396] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    2.962292] init: - preinit -
[    4.384411] rt3050-esw 10110000.esw: link changed 0x00
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3[    4.583806] random: procd: uninitialized urandom read (4 bytes read)
] or [4] key and hit [enter] to select the debug level
[    7.720341] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[    7.764542] urandom-seed: Seed file not found (/etc/urandom.seed)
[    7.904087] procd: - early -
[    7.909996] procd: - watchdog -
[    7.920624] rt3050-esw 10110000.esw: link changed 0x10
[    8.505187] procd: - watchdog -
[    8.511829] procd: - ubus -
[    8.593332] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.605999] rt3050-esw 10110000.esw: link changed 0x18
[    8.727290] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.740510] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.754288] procd: - init -
Please press Enter to activate this console.
[    9.916960] kmodloader: loading kernel modules from /etc/modules.d/*
[   10.140706] urngd: v1.0.0 started.
[   10.235574] nat46: module (version 683fbd2b765506332a1af141545652bf58f03166) loaded.
[   10.283603] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.316489] Loading modules backported from Linux version v5.3-rc4-0-gd45331b00ddb
[   10.331554] Backport generated by backports.git v5.3-rc4-1-0-g4ec72687
[   10.398397] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.442233] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[   10.682682] xt_time: kernel timezone is -0000
[   10.977902] random: crng init done
[   10.984640] random: 6 urandom warning(s) missed due to ratelimiting
[   11.034113] mt76_wmac 10300000.wmac: ASIC revision: 76280001
[   12.068989] mt76_wmac 10300000.wmac: Firmware Version: 20151201
[   12.080789] mt76_wmac 10300000.wmac: Build Time: 20151201183641
[   12.106712] mt76_wmac 10300000.wmac: firmware init done
[   12.320920] mt76x2e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
[   12.333476] mt76x2e 0000:01:00.0: ASIC revision: 76120044
[   13.305510] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a
[   13.323665] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
[   13.334612] mt76x2e 0000:01:00.0: Build: 1
[   13.342731] mt76x2e 0000:01:00.0: Build Time: 201507311614____
[   13.376709] mt76x2e 0000:01:00.0: Firmware running!
[   13.413026] PPP generic driver version 2.4.2
[   13.434463] NET: Registered protocol family 24
[   13.457255] kmodloader: done loading kernel modules from /etc/modules.d/*
[   81.007133] rt3050-esw 10110000.esw: link changed 0x00
[   84.725977] rt3050-esw 10110000.esw: link changed 0x10
[   85.210456] rt3050-esw 10110000.esw: link changed 0x18
[   87.717761] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   87.766439] br-lan: port 1(eth0.1) entered blocking state
[   87.777384] br-lan: port 1(eth0.1) entered disabled state
[   87.788486] device eth0.1 entered promiscuous mode
[   87.798020] device eth0 entered promiscuous mode
[   87.822336] jffs2_build_filesystem(): unlocking the mtd device... 
[   87.822399] done.
[   87.838517] jffs2_build_filesystem(): erasing all blocks after the end marker... 
[   87.963432] br-lan: port 1(eth0.1) entered blocking state
[   87.989006] br-lan: port 1(eth0.1) entered forwarding state
[   88.000788] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   88.797252] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   92.168458] done.
[   92.172311] jffs2: notice: (1302) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   92.572867] overlayfs: upper fs does not support tmpfile.



BusyBox v1.31.0 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r0+11022-f01af852e5
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#
広告

コメントを残す

以下に詳細を記入するか、アイコンをクリックしてログインしてください。

WordPress.com ロゴ

WordPress.com アカウントを使ってコメントしています。 ログアウト /  変更 )

Google フォト

Google アカウントを使ってコメントしています。 ログアウト /  変更 )

Twitter 画像

Twitter アカウントを使ってコメントしています。 ログアウト /  変更 )

Facebook の写真

Facebook アカウントを使ってコメントしています。 ログアウト /  変更 )

%s と連携中