メルカリにおいて適当にI-O DATAのNASを眺めていたところ、ジャンクとして出品されていたのを見つけたもの。
2ドライブ対応で、なおかつ2.5GbE対応であることから惹かれたものの、当初は自室に置き場所が無いなどの理由から見送るつもりであった。が、徐々に価格設定が落ち、3k落ちたところでかなり悩んだ末に購入してしまった。自室スペースの死。
弄っていくのでメモ。
U-Boot
この機種はHDL-A/HDL2-Aと異なり、U-Bootのブート中断が消されておらず止めることが可能だった。
- help
HDL-AA>> help ? - alias for 'help' Creset - Creset - Run 'reset' or boot command in a loop, while counting. SatR - Sample At Reset sub-system active_units- print active units on board base - print or set address offset bdinfo - print Board Info structure boot - boot default, i.e., run 'bootcmd' boot_menu- command allows to select boot script from boot device example: boot_menu bootd - boot default, i.e., run 'bootcmd' bootelf - Boot from an ELF image in memory bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol bootvx - Boot vxWorks from an ELF image bootz - boot Linux zImage image from memory bubt - bubt - Burn an image on the Boot flash device. chpart - change active partition cmp - memory compare coninfo - print console devices and information cp - memory copy cpss_env- set cpss environment variables permanently crc32 - checksum calculation date - get/set/reset date & time ddrPhyRead- ddrPhyRead - Read DDR PHY register ddrPhyWrite- ddrPhyWrite - Write DDR PHY register dhcp - boot image via network using DHCP/TFTP protocol diskboot- diskboot- boot from IDE device dma - dma - Perform DMA using the XOR engine echo - echo args to console editenv - edit environment variable eeprom - EEPROM sub-system env - environment handling commands exit - exit script ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) ext4load- load binary file from a Ext4 filesystem ext4ls - list files in a directory (default /) ext4write- create a file in the root directory false - do nothing, unsuccessfully fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) fdt - flattened device tree utility commands flash_part_print- flash_part_print - print spi/nand FLASH memory information fsinfo - print information about filesystems fsload - load binary file from a filesystem image go - start application at address 'addr' hdl - HDL command help - print command description/usage hwreset - turn RTS/CTS hardware flow control in serial line on/off i2c - I2C sub-system ide - ide - IDE sub-system iminfo - print header information for application image imxtract- extract a part of a multi-image ir - ir - reading and changing MV internal register values. itest - return true/false on integer compare loadb - load binary file over serial line (kermit mode) loads - load S-Record file over serial line loadx - load binary file over serial line (xmodem mode) loady - load binary file over serial line (ymodem mode) loop - infinite loop on address range ls - list files in a directory (default /) map - map - Display address decode windows md - memory display me - me - PCIe master enable mm - memory modify (auto-incrementing address) mmc - MMC sub system mmcinfo - display MMC info mp - mp - map PCIe BAR mtdburn - Burn a Linux image and Filesystem` on the NAND/SPI flash. mtdparts- define flash/nand partitions mtest - simple RAM read/write test mvsource- mvsource - Burn a script image on flash device. mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nfs - boot image via network using NFS protocol nm - memory modify (constant address) pci - list and access PCI Configuration Space pciePhyRead- phyRead - Read PCI-E Phy register pciePhyWrite- pciePhyWrite - Write PCI-E Phy register phyRead - phyRead - Read Phy register phyWrite- phyWrite - Write Phy register ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables pxe - commands to get and boot from pxe files qsgmii_sel- Select SFP or QSGMII modes on bc2. rcvr - rcvr - Start recovery process (with TFTP server) reset - Perform RESET of the CPU resetenv- resetenv - Erase environment sector to reset all variables to default. run - run commands in an environment variable saveenv - save environment variables to persistent storage scsi - SCSI sub-system scsiboot- boot from SCSI device se - se - PCIe Slave enable setenv - set environment variables sf - SPI flash sub-system sg - sg - scanning the PHYs status showvar - print local hushshell variables sleep - delay execution for some time smiscan - smiscan - Scan for marvell smi devices. source - run script from memory sp - scan and detect all devices on PCI-e interface sspi - SPI utility command stage_boot- command to load script/image from different devices example: stage_boot hd_img pxe switchCountersRead- switchCntPrint - Read switch port counters. switchPhyRegRead- - Read switch register switchPhyRegWrite- - Write switch register switchRegRead- switchRegRead - Read switch register switchRegWrite- switchRegWrite - Write switch register sys_restore- sys_restore - Search for install script on USB DOK and start installation of linux kernel and rootfs. sysboot - command to get and boot from syslinux files temp - temp - Display the device temperature. tempCmd0- tempCmd - This command allocated for monitor extinction tempCmd1- tempCmd - This command allocated for monitor extinction tempCmd2- tempCmd - This command allocated for monitor extinction tempCmd3- tempCmd - This command allocated for monitor extinction test - minimal test like /bin/sh tftpboot- boot image via network using TFTP protocol training- training - prints the results of the DDR3 Training. trainingStability- training - prints the results of the DDR3 Training. true - do nothing, successfully ts_report- ts_report - report touch screen coordinate ts_test - ts_test - test touch screen ubi - ubi commands ubifsload- load file from an UBIFS filesystem ubifsls - list files in a directory ubifsmount- mount UBIFS volume ubifsumount- unmount UBIFS volume usb - USB sub-system usbboot - boot from USB device version - print monitor, compiler and linker version whoAmI - - reading CPU ID
- version
HDL-AA>> version U-Boot 2013.01 (Oct 25 2019 - 09:26:29) MV: 2015_T1.0p16 I-O: 0.47 arm-marvell-linux-gnueabi-gcc (Marvell GCC release 20160226-c4af733b 64K MAXPAGESIZE ALIGN) 4.6.4 GNU ld (Marvell GCC release 20160226-c4af733b 64K MAXPAGESIZE ALIGN) 2.22.0.20120801
- printenv
HDL-AA>> printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=console=ttyS0,115200 mtdparts=spi0.0:960k(boot),64k(env),-(system) initrd=0x3000040 rw root=/dev/md2 rootfstype=ext4 rw rootdelay=2 init=/lib/sysvinit/init bootargs_dflt=$console $nandEcc $mtdparts_lgcy $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/sda1 rw rootdelay=2 bootcmd=hdl init; sleep 10; if scsi reset;then ext4load scsi 0:1 $kernel_addr $image_name && ext4load scsi 0:1 $fdt_addr $fdtfile && ext4load scsi 0:1 $initrd_addr $initrd_name && bootz $kernel_addr $initrd_addr $fdt_addr;ext4load scsi 1:1 $kernel_addr $image_name && ext4load scsi 1:1 $fdt_addr $fdtfile && ext4load scsi 1:1 $initrd_addr $initrd_name && bootz $kernel_addr $initrd_addr $fdt_addr;fi;fsload $kernel_addr $image_name && fsload $fdt_addr $fdtfile && fsload $initrd_addr $initrd_name && bootz $kernel_addr $initrd_addr $fdt_addr;echo giveup... bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts_lgcy $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootm $loadaddr; bootdelay=0 cacheShare=no console=console=ttyS0,115200 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:e8:55:52 eth1mtu=1500 eth2addr=00:50:43:e8:8e:52 eth2mtu=1500 eth3addr=00:50:43:55:8e:e8 eth3mtu=1500 ethact=egiga0 ethaddr=34:76:C5:xx:xx:05 ethmtu=1500 ethprime=egiga0 fdt_addr=0x1000000 fdt_flash_addr=0x6f0000 fdt_flash_size=0x10000 fdt_size=0x10000 fdt_skip_update=yes fdtaddr=0x1000000 fdtfile=/hdl-aa.dtb filesize=0x1000000 ide_path=/ image_name=/zImage initrd_addr=0x3000000 initrd_addr_entry=0x3000040 initrd_flash_addr=0x700000 initrd_flash_size=0x900000 initrd_name=/uInitrd initrd_size=0x900000 ipaddr=192.168.1.100 kernel_addr=0x2000000 kernel_addr_r=2080000 kernel_flash_addr=0x100000 kernel_flash_size=0x5f0000 kernel_size=0x5f0000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 limit_dram_size=yes loadaddr=0x02000000 loads_echo=0 mtddevname=jffs2 mtddevnum=2 mtdids=nor1=spi_flash mtdparts=mtdparts=spi_flash:960k(u-boot),64k(env),-(jffs2) mtdparts_lgcy=mtdparts=spi_flash:4m(boot),-(spi-rootfs) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:52:8e:e8 nandEcc=nfcConfig=8bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nor1,2 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ run_script=no sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr scsidevs=0 sd_detection_dat3=no serverip=192.168.1.1 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts_lgcy root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usb1Mode=host usbActive=1 usbType=3 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 zhcc=G82573813 Environment size: 4339/65532 bytes
bootcmd整形:
hdl init; sleep 10; # SCSI (SATA) リセットOK if scsi reset;then # SCSI 0:1 (SATA0) からブート試行 ext4load scsi 0:1 $kernel_addr $image_name && \ ext4load scsi 0:1 $fdt_addr $fdtfile && \ ext4load scsi 0:1 $initrd_addr $initrd_name && \ bootz $kernel_addr $initrd_addr $fdt_addr; # SCSI 1:1 (SATA1) からブート試行 ext4load scsi 1:1 $kernel_addr $image_name && \ ext4load scsi 1:1 $fdt_addr $fdtfile && \ ext4load scsi 1:1 $initrd_addr $initrd_name && \ bootz $kernel_addr $initrd_addr $fdt_addr; fi; # SPI-NOR Flashからブート試行 fsload $kernel_addr $image_name && \ fsload $fdt_addr $fdtfile && \ fsload $initrd_addr $initrd_name && \ bootz $kernel_addr $initrd_addr $fdt_addr; echo giveup... - tftpboot
何故か死ぬHDL-AA>> tftpboot mvEgigaInit: egiga0 mvNetaPortEnable failed (error) mvEgigaInit: egiga0 failed
- bdinfo
HDL-AA>> bdinfo arch_number = 0x00000210 boot_params = 0x00000100 DRAM bank = 0x00000000 -> start = 0x00000000 -> size = 0x20000000 DRAM bank = 0x00000001 -> start = 0x00000000 -> size = 0x00000000 ethaddr = 34:76:C5:xx:xx:05 ip_addr = 192.168.1.100 baudrate = 115200 bps TLB addr = 0x1FFF0000 relocaddr = 0x1FECF000 reloc off = 0x1FECF000 irq_sp = 0x1F9BEF30 sp start = 0x1F9BEF20 FB base = 0x00000000
Kernel
ファームウェアインストール済みのHDDは無い為、SPI-NOR Flash内に格納されているファームウェアで確認
- uname -a
/ # uname -a Linux landisk 3.10.70 #1 SMP Thu Nov 26 18:11:41 JST 2020 armv7l GNU/Linux
- cat /proc/version
/ # cat /proc/version Linux version 3.10.70 (root@buildarmsrv) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 SMP Thu Nov 26 18:11:41 JST 2020
- cat /proc/cpuinfo
/ # cat /proc/cpuinfo processor : 0 model name : ARMv7 Processor rev 1 (v7l) BogoMIPS : 2655.84 Features : swp half thumb fastmult vfp edsp neon vfpv3 tls CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x4 CPU part : 0xc09 CPU revision : 1 processor : 1 model name : ARMv7 Processor rev 1 (v7l) BogoMIPS : 2655.84 Features : swp half thumb fastmult vfp edsp neon vfpv3 tls CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x4 CPU part : 0xc09 CPU revision : 1 Hardware : Marvell Armada 380/381/382/383/384/385/388 (Device Tree) Revision : 0000 Serial : 0000000000000000
- cat /proc/meminfo
/ # cat /proc/meminfo MemTotal: 509448 kB MemFree: 469432 kB Buffers: 0 kB Cached: 8340 kB SwapCached: 0 kB Active: 4160 kB Inactive: 4964 kB Active(anon): 784 kB Inactive(anon): 92 kB Active(file): 3376 kB Inactive(file): 4872 kB Unevictable: 0 kB Mlocked: 0 kB HighTotal: 0 kB HighFree: 0 kB LowTotal: 509448 kB LowFree: 469432 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 756 kB Mapped: 912 kB Shmem: 92 kB Slab: 27440 kB SReclaimable: 3304 kB SUnreclaim: 24136 kB KernelStack: 488 kB PageTables: 52 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 254724 kB Committed_AS: 1980 kB VmallocTotal: 515072 kB VmallocUsed: 5520 kB VmallocChunk: 484348 kB
- cat /proc/mtd
/ # cat /proc/mtd dev: size erasesize name mtd0: 000f0000 00010000 "boot" mtd1: 00010000 00010000 "env" mtd2: 00f00000 00010000 "system"
- ls -alh /proc/nas_ctrl/
/ # ls -alh /proc/nas_ctrl/ total 0 dr-xr-xr-x 2 0 0 0 Jun 18 06:05 . dr-xr-xr-x 76 0 0 0 Jan 1 1970 .. -rw-rw-rw- 1 0 0 0 Jun 18 06:05 boardmodel -rw-rw-rw- 1 0 0 0 Jun 18 06:05 btnled -rw-rw-rw- 1 0 0 0 Jun 18 06:05 melody
- cat /proc/nas_ctrl/btnled
/ # cat /proc/nas_ctrl/btnled led_green off led_orange off led_red blink led_hdd1green off led_hdd1red off led_hdd2green off led_hdd2red off led_brightness high btn_power off btn_power_state state_off btn_reset off btn_reset_state state_off
- bootlog
ファームウェアインストール用USBフラッシュメモリとHDDを接続していない為、途中で止まるBootROM - 1.73 Booting from SPI flash General initialization - Version: 1.0.0 AVS selection from EFUSE disabled (Skip reading EFUSE values) Overriding default AVS value to: 0x23 Detected Device ID 6811 High speed PHY - Version: 2.0 Init HDL board board SerDes lanes topology details: | Lane # | Speed| Type | ------------------------------| | 0 | 0 | SGMII0 | | 1 | 6 | SATA0 | | 2 | 6 | SATA1 | | 3 | 5 | USB3 HOST1 | ------------------------------- High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.46.0 DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED ============================================================ HDL-AA series Initial boot loader Copyright (C) 2015-2017 I-O DATA DEVICE, INC. ============================================================ ** LOADER ** U-Boot 2013.01 (Oct 25 2019 - 09:26:29) MV: 2015_T1.0p16 I-O: 0.47 Board: HDL-AA SoC: MV88F6811 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR3 @ 666 [MHz] DDR3 16 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB NAND: mvNfcInit() failed. 0 MiB SPI: SF: Detected W25Q128 with page size 64 KiB, total 16 MiB MMC: mv_sdh: 0 SF: Detected W25Q128 with page size 64 KiB, total 16 MiB USB3.0 1: Host Mode Map: Code: 0x1fecf000:0x1ff96474 BSS: 0x1ffefdac Stack: 0x1f9bef20 Heap: 0x1f9bf000:0x1fecf000 U-Boot Environment: 0x000f0000:0x00100000 (SPI) Board configuration detected: mvBoardEgigaPhyInit in Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | SGMII | In-Band | egiga0 [PRIME] Hit any key to stop autoboot: 0 failed to read mcu workaround for reset address. boot by AC. setting is not boot by AC. phy: page = 0 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 1 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 2 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 3 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 4 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 5 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 6 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 7 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 8 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 9 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 10 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 11 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 12 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 13 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 14 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 15 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 16 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 phy: page = 17 addr +0 +1 +2 +3 +4 +5 +6 +7 0000: 0000 0000 0000 0000 0000 0000 0000 0000 0008: 0000 0000 0000 0000 0000 0000 0000 0000 0010: 0000 0000 0000 0000 0000 0000 0000 0000 0018: 0000 0000 0000 0000 0000 0000 0000 0000 iodata GPIO power off. BootROM - 1.73 Booting from SPI flash General initialization - Version: 1.0.0 AVS selection from EFUSE disabled (Skip reading EFUSE values) Overriding default AVS value to: 0x23 Detected Device ID 6811 High speed PHY - Version: 2.0 Init HDL board board SerDes lanes topology details: | Lane # | Speed| Type | ------------------------------| | 0 | 0 | SGMII0 | | 1 | 6 | SATA0 | | 2 | 6 | SATA1 | | 3 | 5 | USB3 HOST1 | ------------------------------- High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.46.0 DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED ============================================================ HDL-AA series Initial boot loader Copyright (C) 2015-2017 I-O DATA DEVICE, INC. ============================================================ ** LOADER ** U-Boot 2013.01 (Oct 25 2019 - 09:26:29) MV: 2015_T1.0p16 I-O: 0.47 Board: HDL-AA SoC: MV88F6811 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR3 @ 666 [MHz] DDR3 16 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB NAND: mvNfcInit() failed. 0 MiB SPI: SF: Detected W25Q128 with page size 64 KiB, total 16 MiB MMC: mv_sdh: 0 SF: Detected W25Q128 with page size 64 KiB, total 16 MiB USB3.0 1: Host Mode Map: Code: 0x1fecf000:0x1ff96474 BSS: 0x1ffefdac Stack: 0x1f9bef20 Heap: 0x1f9bf000:0x1fecf000 U-Boot Environment: 0x000f0000:0x00100000 (SPI) Board configuration detected: mvBoardEgigaPhyInit in Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | SGMII | In-Band | egiga0 [PRIME] Hit any key to stop autoboot: 0 failed to read mcu workaround for reset address. Reset SCSI AHCI init for unit0 SATA link 0 timeout. SATA link 1 timeout. Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Found 0 device(s). ** Bad device scsi 0 ** ** Bad device scsi 1 ** ### JFFS2 loading '/zImage' to 0x2000000 Scanning JFFS2 FS: SF: Detected W25Q128 with page size 64 KiB, total 16 MiB . done. ### JFFS2 load complete: 3535504 bytes loaded to 0x2000000 ### JFFS2 loading '/hdl-aa.dtb' to 0x1000000 ### JFFS2 load complete: 14041 bytes loaded to 0x1000000 ### JFFS2 loading '/uInitrd' to 0x3000000 ### JFFS2 load complete: 3329208 bytes loaded to 0x3000000 ## Loading init Ramdisk from Legacy Image at 03000000 ... Image Name: HDL-AAX Created: 2022-05-09 0:42:20 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 3329144 Bytes = 3.2 MiB Load Address: 00000000 Entry Point: 00000000 ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x01000000 Loading Ramdisk to 1f690000, end 1f9bcc78 ... OK Loading Device Tree to 00ff9000, end 00fff6d8 ... OK Skipping Device Tree update ('fdt_skip_update' = yes) Limit DDR size at 3GB due to power of 2 requirement of Address decoding Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 3.10.70 (root@buildarmsrv) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 SMP Thu Nov 26 18:11:41 JST 2020 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), model: HDL-AA Memory policy: ECC disabled, Data cache writealloc PERCPU: Embedded 9 pages/cpu @c0e4e000 s12544 r8192 d16128 u36864 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyS0,115200 mtdparts=spi0.0:960k(boot),64k(env),-(system) initrd=0x3000040 rw root=/dev/md2 rootfstype=ext4 rw rootdelay=2 init=/lib/sysvinit/init PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 512MB = 512MB total Memory: 505868k/505868k available, 18420k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc08fa7a8 (9162 kB) .init : 0xc08fb000 - 0xc094e100 ( 333 kB) .data : 0xc0950000 - 0xc09b5d00 ( 408 kB) .bss : 0xc09b5d00 - 0xc0a440a4 ( 569 kB) Hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. NR_IRQS:16 nr_irqs:16 16 LSP version: linux-3.10.70-2015_T1.1p7 sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms L310 cache controller enabled l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B Console: colour dummy device 80x30 Calibrating delay loop... 2655.84 BogoMIPS (lpj=13279232) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0xc067e628 - 0xc067e680 mvebu-pmsu: Initializing Power Management Service Unit Initializing CPU Reset module CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (5311.69 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized mvebu-soc-id: MVEBU SoC ID=0x6811, Rev=0x4 xor: measuring software checksum speed arm4regs : 2366.000 MB/sec 8regs : 1630.000 MB/sec 32regs : 1658.400 MB/sec xor: using function: arm4regs (2366.000 MB/sec) pinctrl core: initialized pinctrl subsystem regulator-dummy: no parameters NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations irq: Cannot allocate irq_descs @ IRQ194, assuming pre-allocated irq: Cannot allocate irq_descs @ IRQ226, assuming pre-allocated bio: create slab at 0 raid6: int32x1 199 MB/s raid6: int32x2 274 MB/s raid6: int32x4 274 MB/s raid6: int32x8 302 MB/s raid6: using algorithm int32x8 (302 MB/s) raid6: using intx1 recovery algorithm vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered Switching to clocksource armada_370_xp_clocksource FS-Cache: Loaded NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... Freeing initrd memory: 3248K (df690000 - df9bc000) VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher FS-Cache: Netfs 'nfs' registered for caching NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Key type cifs.spnego registered Key type cifs.idmap registered NTFS driver 2.1.30 [Flags: R/O]. jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.22) SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled msgmni has been set to 994 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver gpio-mcu: gmcu_dev = f800000 (M: 248, m: 0) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A console [ttyS0] enabled brd: module loaded ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi0 : ahci_mv_platform scsi1 : ahci_mv_platform ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 m25p80 spi0.0: found w25q128, expected mx25l12805d m25p80 spi0.0: w25q128 (16384 Kbytes) 3 cmdlinepart partitions found on MTD device spi0.0 Creating 3 MTD partitions on "spi0.0": 0x000000000000-0x0000000f0000 : "boot" 0x0000000f0000-0x000000100000 : "env" 0x000000100000-0x000001000000 : "system" bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) errlp [mv_plat_data_get:4663] phy addr:0 errlp [mv_plat_data_get:4692] phy_mode:6 SoC: model = 0x6811, revision = 0x4 mvPncVirtBase = 0xe1400000, pncTcamSize = 1024 o 3 Giga ports supported o SKB recycle supported for SWF (Disabled) o NETA acceleration mode 4 o BM supported for CPU: 4 BM pools o PnC supported (Enabled) o RX Queue support: 8 Queues * 256 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Driver DEBUG statistics enabled port #0: is_sgmii=0, is_rgmii=1, phy_addr=0 o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 o Port 0 is connected to Linux netdevice o eth0, ifindex = 3, GbE port = 0 giga p=0: mtu=1500, mac=34:76:c5:xx:xx:05 (env config) libphy: orion_mdio_bus: probed phy int status:0x0, global phy int status:0x0 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1058000.usb: EHCI Host Controller orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 3.10.70 ehci_hcd usb usb1: SerialNumber: f1058000.usb hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: xHCI Host Controller usb usb2: Manufacturer: Linux 3.10.70 xhci-hcd usb usb2: SerialNumber: f10f0000.usb3 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: xHCI Host Controller usb usb3: Manufacturer: Linux 3.10.70 xhci-hcd usb usb3: SerialNumber: f10f0000.usb3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: xHCI Host Controller usb usb4: Manufacturer: Linux 3.10.70 xhci-hcd usb usb4: SerialNumber: f10f8000.usb3 hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: xHCI Host Controller ata2: SATA link down (SStatus 0 SControl 300) ata1: SATA link down (SStatus 0 SControl 300) usb usb5: Manufacturer: Linux 3.10.70 xhci-hcd usb usb5: SerialNumber: f10f8000.usb3 hub 5-0:1.0: USB hub found hub 5-0:1.0: 1 port detected usbcore: registered new interface driver usblp usbcore: registered new interface driver usb-storage usbcore: registered new interface driver ums-alauda usbcore: registered new interface driver ums-cypress usbcore: registered new interface driver ums-datafab usbcore: registered new interface driver ums_eneub6250 usbcore: registered new interface driver ums-freecom usbcore: registered new interface driver ums-isd200 usbcore: registered new interface driver ums-jumpshot usbcore: registered new interface driver ums-realtek usbcore: registered new interface driver ums-sddr09 usbcore: registered new interface driver ums-sddr55 usbcore: registered new interface driver ums-usbat usb 2-1: new high-speed USB device number 2 using xhci-hcd usb 2-1: New USB device found, idVendor=05e3, idProduct=0608 usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 usb 2-1: Product: USB2.0 Hub hub 2-1:1.0: USB hub found hub 2-1:1.0: 4 ports detected mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 i2c /dev entries driver armada_thermal f10e4078.thermal: Overheat threshold between 92..107 orion_wdt: Initial timeout 171 sec md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 md: multipath personality registered for level -4 device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com dm_crypt using the OCF package. cpuidle: using governor ladder armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0) mvCesaInit: channels=2, session=640, queue=256 armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode cesadev_init(c092e7f8) hidraw: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver drop_monitor: Initializing network drop monitor service TCP: cubic registered NET: Registered protocol family 10 NET: Registered protocol family 17 Key type dns_resolver registered VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 NAS Controller 1.00 regulator-dummy: disabling mvebu-rtc f10a3800.rtc: setting system clock to 2022-06-18 06:34:33 UTC (1655534073) Freeing unused kernel memory: 332K (c08fb000 - c094e000) Loading, please wait... systemd-udevd[94]: starting version 215 Begin: Loading essential drivers ... done. ### probing disks ####################################################### MODEL: HDL2-AAX SATA: D1= D2= USB: D1= D2= D3= ### check F/W installer ################################################# firminstall: probe: SATA: D1= D2= USB: D1= D2= D3= NG_NO_USB_DEVICE ### check USB installer ################################################# usbinstall: probe: SATA: D1= D2= USB: D1= D2= D3= NG_NO_USB_DEVICE ### check initialization ################################################ ### assemble / volume ################################################### BusyBox v1.22.1 (Debian 1:1.22.0-9+deb8u1) built-in shell (ash) Enter 'help' for a list of built-in commands. /bin/sh: can't access tty; job control turned off / # - bootlog（HDL2-AAX0/Eファームウェアインストール → ブート）
HDL2-AAX0/E用ファームウェアのインストールからHDDブート実施までBootROM - 1.73 Booting from SPI flash General initialization - Version: 1.0.0 AVS selection from EFUSE disabled (Skip reading EFUSE values) Overriding default AVS value to: 0x23 Detected Device ID 6811 High speed PHY - Version: 2.0 Init HDL board board SerDes lanes topology details: | Lane # | Speed| Type | ------------------------------| | 0 | 0 | SGMII0 | | 1 | 6 | SATA0 | | 2 | 6 | SATA1 | | 3 | 5 | USB3 HOST1 | ------------------------------- High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.46.0 DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED ============================================================ HDL-AA series Initial boot loader Copyright (C) 2015-2017 I-O DATA DEVICE, INC. ============================================================ ** LOADER ** U-Boot 2013.01 (Oct 25 2019 - 09:26:29) MV: 2015_T1.0p16 I-O: 0.47 Board: HDL-AA SoC: MV88F6811 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR3 @ 666 [MHz] DDR3 16 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB NAND: mvNfcInit() failed. 0 MiB SPI: SF: Detected W25Q128 with page size 64 KiB, total 16 MiB MMC: mv_sdh: 0 SF: Detected W25Q128 with page size 64 KiB, total 16 MiB USB3.0 1: Host Mode Map: Code: 0x1fecf000:0x1ff96474 BSS: 0x1ffefdac Stack: 0x1f9bef20 Heap: 0x1f9bf000:0x1fecf000 U-Boot Environment: 0x000f0000:0x00100000 (SPI) Board configuration detected: mvBoardEgigaPhyInit in Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | SGMII | In-Band | egiga0 [PRIME] Hit any key to stop autoboot: 0 failed to read mcu workaround for reset address. Reset SCSI AHCI init for unit0 Target spinup took 0 ms. Target spinup took 0 ms. Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: Hitachi HDP72505 Rev: GM4O Type: Hard Disk Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Device 1: (1:0) Vendor: ATA Prod.: SAMSUNG HD502HI Rev: 1AG0 Type: Hard Disk Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Found 2 device(s). ** No partition table - scsi 0 ** Failed to mount ext2 filesystem... ** Unrecognized filesystem type ** ### JFFS2 loading '/zImage' to 0x2000000 Scanning JFFS2 FS: SF: Detected W25Q128 with page size 64 KiB, total 16 MiB . done. ### JFFS2 load complete: 3535504 bytes loaded to 0x2000000 ### JFFS2 loading '/hdl-aa.dtb' to 0x1000000 ### JFFS2 load complete: 14041 bytes loaded to 0x1000000 ### JFFS2 loading '/uInitrd' to 0x3000000 ### JFFS2 load complete: 3329208 bytes loaded to 0x3000000 ## Loading init Ramdisk from Legacy Image at 03000000 ... Image Name: HDL-AAX Created: 2022-05-09 0:42:20 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 3329144 Bytes = 3.2 MiB Load Address: 00000000 Entry Point: 00000000 ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x01000000 Loading Ramdisk to 1f690000, end 1f9bcc78 ... OK Loading Device Tree to 00ff9000, end 00fff6d8 ... OK Skipping Device Tree update ('fdt_skip_update' = yes) Limit DDR size at 3GB due to power of 2 requirement of Address decoding Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 3.10.70 (root@buildarmsrv) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 SMP Thu Nov 26 18:11:41 JST 2020 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), model: HDL-AA Memory policy: ECC disabled, Data cache writealloc PERCPU: Embedded 9 pages/cpu @c0e4e000 s12544 r8192 d16128 u36864 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyS0,115200 mtdparts=spi0.0:960k(boot),64k(env),-(system) initrd=0x3000040 rw root=/dev/md2 rootfstype=ext4 rw rootdelay=2 init=/lib/sysvinit/init PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 512MB = 512MB total Memory: 505868k/505868k available, 18420k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc08fa7a8 (9162 kB) .init : 0xc08fb000 - 0xc094e100 ( 333 kB) .data : 0xc0950000 - 0xc09b5d00 ( 408 kB) .bss : 0xc09b5d00 - 0xc0a440a4 ( 569 kB) Hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. NR_IRQS:16 nr_irqs:16 16 LSP version: linux-3.10.70-2015_T1.1p7 sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms L310 cache controller enabled l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B Console: colour dummy device 80x30 Calibrating delay loop... 2655.84 BogoMIPS (lpj=13279232) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0xc067e628 - 0xc067e680 mvebu-pmsu: Initializing Power Management Service Unit Initializing CPU Reset module CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (5311.69 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized mvebu-soc-id: MVEBU SoC ID=0x6811, Rev=0x4 xor: measuring software checksum speed arm4regs : 2366.000 MB/sec 8regs : 1630.000 MB/sec 32regs : 1658.400 MB/sec xor: using function: arm4regs (2366.000 MB/sec) pinctrl core: initialized pinctrl subsystem regulator-dummy: no parameters NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations irq: Cannot allocate irq_descs @ IRQ194, assuming pre-allocated irq: Cannot allocate irq_descs @ IRQ226, assuming pre-allocated bio: create slab <bio-0> at 0 raid6: int32x1 199 MB/s raid6: int32x2 274 MB/s raid6: int32x4 274 MB/s raid6: int32x8 302 MB/s raid6: using algorithm int32x8 (302 MB/s) raid6: using intx1 recovery algorithm vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered Switching to clocksource armada_370_xp_clocksource FS-Cache: Loaded NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... Freeing initrd memory: 3248K (df690000 - df9bc000) VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher FS-Cache: Netfs 'nfs' registered for caching NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Key type cifs.spnego registered Key type cifs.idmap registered NTFS driver 2.1.30 [Flags: R/O]. jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.22) SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled msgmni has been set to 994 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver gpio-mcu: gmcu_dev = f800000 (M: 248, m: 0) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A console [ttyS0] enabled brd: module loaded ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi0 : ahci_mv_platform scsi1 : ahci_mv_platform ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 m25p80 spi0.0: found w25q128, expected mx25l12805d m25p80 spi0.0: w25q128 (16384 Kbytes) 3 cmdlinepart partitions found on MTD device spi0.0 Creating 3 MTD partitions on "spi0.0": 0x000000000000-0x0000000f0000 : "boot" 0x0000000f0000-0x000000100000 : "env" 0x000000100000-0x000001000000 : "system" bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) errlp [mv_plat_data_get:4663] phy addr:0 errlp [mv_plat_data_get:4692] phy_mode:6 SoC: model = 0x6811, revision = 0x4 mvPncVirtBase = 0xe1400000, pncTcamSize = 1024 o 3 Giga ports supported o SKB recycle supported for SWF (Disabled) o NETA acceleration mode 4 o BM supported for CPU: 4 BM pools o PnC supported (Enabled) o RX Queue support: 8 Queues * 256 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Driver DEBUG statistics enabled port #0: is_sgmii=0, is_rgmii=1, phy_addr=0 o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 o Port 0 is connected to Linux netdevice o eth0, ifindex = 3, GbE port = 0 giga p=0: mtu=1500, mac=34:76:c5:xx:xx:05 (env config) libphy: orion_mdio_bus: probed phy int status:0x0, global phy int status:0x0 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1058000.usb: EHCI Host Controller orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 3.10.70 ehci_hcd usb usb1: SerialNumber: f1058000.usb hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: xHCI Host Controller usb usb2: Manufacturer: Linux 3.10.70 xhci-hcd usb usb2: SerialNumber: f10f0000.usb3 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: xHCI Host Controller usb usb3: Manufacturer: Linux 3.10.70 xhci-hcd usb usb3: SerialNumber: f10f0000.usb3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: xHCI Host Controller usb usb4: Manufacturer: Linux 3.10.70 xhci-hcd usb usb4: SerialNumber: f10f8000.usb3 hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: xHCI Host Controller usb usb5: Manufacturer: Linux 3.10.70 xhci-hcd usb usb5: SerialNumber: f10f8000.usb3 hub 5-0:1.0: USB hub found hub 5-0:1.0: 1 port detected usbcore: registered new interface driver usblp usbcore: registered new interface driver usb-storage usbcore: registered new interface driver ums-alauda usbcore: registered new interface driver ums-cypress usbcore: registered new interface driver ums-datafab usbcore: registered new interface driver ums_eneub6250 usbcore: registered new interface driver ums-freecom usbcore: registered new interface driver ums-isd200 usbcore: registered new interface driver ums-jumpshot usbcore: registered new interface driver ums-realtek usbcore: registered new interface driver ums-sddr09 usbcore: registered new interface driver ums-sddr55 usbcore: registered new interface driver ums-usbat ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-8: Hitachi HDP725050GLA360, GM4OA52A, max UDMA/133 ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) usb 2-1: new high-speed USB device number 2 using xhci-hcd ata2.00: ATA-7: SAMSUNG HD502HI, 1AG01118, max UDMA7 ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA Hitachi HDP72505 GM4O PQ: 0 ANSI: 5 usb 2-1: New USB device found, idVendor=05e3, idProduct=0608 usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 usb 2-1: Product: USB2.0 Hub ata2.00: configured for UDMA/133 hub 2-1:1.0: USB hub found hub 2-1:1.0: 4 ports detected sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD502HI 1AG0 PQ: 0 ANSI: 5 sd 1:0:0:0: Attached scsi generic sg1 type 0 sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: unknown partition table sd 0:0:0:0: [sda] Attached SCSI disk sdb: sdb1 sdb2 sd 1:0:0:0: [sdb] Attached SCSI disk usb 2-1.2: new high-speed USB device number 3 using xhci-hcd usb 2-1.2: New USB device found, idVendor=30de, idProduct=6544 usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1.2: Product: TransMemory usb 2-1.2: Manufacturer: KIOXIA usb 2-1.2: SerialNumber: 0022CFF6B8BBC540E88C0355 usb 2-1.2: ep 0x81 - rounding interval to 128 microframes, ep desc says 255 microframes usb 2-1.2: ep 0x2 - rounding interval to 128 microframes, ep desc says 255 microframes usb-storage 2-1.2:1.0: USB Mass Storage device detected scsi2 : usb-storage 2-1.2:1.0 mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 i2c /dev entries driver armada_thermal f10e4078.thermal: Overheat threshold between 92..107 orion_wdt: Initial timeout 171 sec md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 md: multipath personality registered for level -4 device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com dm_crypt using the OCF package. cpuidle: using governor ladder armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0) mvCesaInit: channels=2, session=640, queue=256 armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode cesadev_init(c092e7f8) hidraw: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver drop_monitor: Initializing network drop monitor service TCP: cubic registered NET: Registered protocol family 10 NET: Registered protocol family 17 Key type dns_resolver registered VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 NAS Controller 1.00 regulator-dummy: disabling mvebu-rtc f10a3800.rtc: setting system clock to 2022-06-18 12:54:09 UTC (1655556849) Freeing unused kernel memory: 332K (c08fb000 - c094e000) Loading, please wait... systemd-udevd[96]: starting version 215 scsi 2:0:0:0: Direct-Access KIOXIA TransMemory 1.00 PQ: 0 ANSI: 4 sd 2:0:0:0: Attached scsi generic sg2 type 0 sd 2:0:0:0: [sdc] 30274560 512-byte logical blocks: (15.5 GB/14.4 GiB) sd 2:0:0:0: [sdc] Write Protect is off sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sdc: sdc1 sd 2:0:0:0: [sdc] Attached SCSI removable disk Begin: Loading essential drivers ... done. ### probing disks ####################################################### MODEL: HDL2-AAX sda: unknown partition table sdc: sdc1 sda: unknown partition table sdb: sdb1 sdb2 sdb: sdb1 sdb2 sdc: sdc1 sdc: sdc1 SATA: D1=/dev/sdb D2=/dev/sda USB: D1=/dev/sdc D2= D3= ### check F/W installer ################################################# ### USB install start #################################################### ###### install from /mnt/usb1/firmware/2aax/script.sh ###### OPTIONS: O_SHELL= O_SHORTP= O_NOFLASH= O_NOEPCLEAN= O_NOSMART=1 O_NOHDDCHK=1 O_ACLEAN= O_RESETRTC= ### USBINSTALL: check internal HDDs ###################################### ###### check internal HDD existence ###### OK ###### check internal HDD size ###### OK ###### enable S.M.A.R.T. ###### OK ### USBINSTALL: create internal volumes ################################## ###### partition internal disks ###### sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sda: unknown partition table sda: sda1 sda2 sda3 sda4 sda5 sda6 MODEL: HDL2-AAX sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sda: sda1 sda2 sda3 sda4 sda5 sda6 sda: sda1 sda2 sda3 sda4 sda5 sda6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 SATA: D1=/dev/sdb D2=/dev/sda USB: D1=/dev/sdc D2= D3= OK ###### create volume 1 ###### EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) OK ###### create volume 2 ###### md: bind<sdb2> md: bind<sda2> md/raid1:md2: not clean -- starting background reconstruction md/raid1:md2: active with 2 out of 3 mirrors md2: detected capacity change from 0 to 2145386496 md: resync of RAID array md2 md: minimum _guaranteed_ speed: 1000 KB/sec/disk. md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync. md: using 128k window, over a total of 2095104k. md2: unknown partition table ###### wait for resync md2 ###### md: md2: resync done. ###### resync md2 complete ###### OK ###### create volume 3 ###### OK ###### create volume 4 ###### EXT4-fs (sdb4): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null) OK ###### create volume 5 ###### md: bind<sdb5> md: bind<sda5> md/raid1:md5: not clean -- starting background reconstruction md/raid1:md5: active with 2 out of 3 mirrors md5: detected capacity change from 0 to 1072693248 md: resync of RAID array md5 md5: unknown partition table md: minimum _guaranteed_ speed: 1000 KB/sec/disk. md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync. md: using 128k window, over a total of 1047552k. ###### wait for resync md5 ###### md: md5: resync done. ###### resync md5 complete ###### OK ###### create volume 6 ###### ##### create vfsext ###### ##### format satad1p6 ###### ##### format satad2p6 ###### OK ### USBINSTALL: install files ############################################ EXT4-fs (md2): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (md5): mounted filesystem with ordered data mode. Opts: (null) XFS (sdb6): Mounting Filesystem XFS (sdb6): Ending clean mount XFS (sda6): Mounting Filesystem XFS (sda6): Ending clean mount Create signature - 3F33B879 vfsext signature - 3F33B879 vfsext: assume all device is new. OK ### USBINSTALL: install files for boot ################################### EXT4-fs (md2): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) OK ### USBINSTALL: initialize board config ################################## ##### initialize flash ##### FLASH0 Comparing... FLASH0 no change FLASH1 Writing... done. FLASH1 Comparing... OK OK ##### initialize MCU ##### OK ###### disable RTC alarm ###### OK ###### reset EEPROM ###### .......W...W...W ...W..........WW W............... ................ ................ ................ ................ ................ ................ ................ ................ ................ ................ ................ ................ ................ OK ##### disable AC auto power on ##### OK ###### enable WoL ###### OK ##### enable buzzer ##### OK ##### set LED brightness ##### OK ### USB install end ###################################################### sd 1:0:0:0: [sdb] Synchronizing SCSI cache sd 1:0:0:0: [sdb] Stopping disk sd 0:0:0:0: [sda] Synchronizing SCSI cache sd 0:0:0:0: [sda] Stopping disk xhci-hcd f10f8000.usb3: remove, state 4 usb usb5: USB disconnect, device number 1 xhci-hcd f10f8000.usb3: USB bus 5 deregistered xhci-hcd f10f8000.usb3: remove, state 4 usb usb4: USB disconnect, device number 1 xhci-hcd f10f8000.usb3: USB bus 4 deregistered xhci-hcd f10f0000.usb3: remove, state 4 usb usb3: USB disconnect, device number 1 xhci-hcd f10f0000.usb3: USB bus 3 deregistered xhci-hcd f10f0000.usb3: remove, state 1 usb usb2: USB disconnect, device number 1 usb 2-1: USB disconnect, device number 2 usb 2-1.2: USB disconnect, device number 3 xhci-hcd f10f0000.usb3: USB bus 2 deregistered Shutting Down Marvell Ethernet Driver Power down. Wake On LAN Enable by ethtool. status reg@0xf040:0x0 status reg@0xf042:0x0 status reg@0xf06f:0x0 iodata GPIO power off... BootROM - 1.73 Booting from SPI flash General initialization - Version: 1.0.0 AVS selection from EFUSE disabled (Skip reading EFUSE values) Overriding default AVS value to: 0x23 Detected Device ID 6811 High speed PHY - Version: 2.0 Init HDL board board SerDes lanes topology details: | Lane # | Speed| Type | ------------------------------| | 0 | 0 | SGMII0 | | 1 | 6 | SATA0 | | 2 | 6 | SATA1 | | 3 | 5 | USB3 HOST1 | ------------------------------- High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.46.0 DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED ============================================================ HDL-AA series Initial boot loader Copyright (C) 2015-2017 I-O DATA DEVICE, INC. ============================================================ ** LOADER ** U-Boot 2013.01 (Oct 25 2019 - 09:26:29) MV: 2015_T1.0p16 I-O: 0.47 Board: HDL-AA SoC: MV88F6811 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR3 @ 666 [MHz] DDR3 16 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB NAND: mvNfcInit() failed. 0 MiB SPI: SF: Detected W25Q128 with page size 64 KiB, total 16 MiB MMC: mv_sdh: 0 SF: Detected W25Q128 with page size 64 KiB, total 16 MiB USB3.0 1: Host Mode Map: Code: 0x1fecf000:0x1ff96474 BSS: 0x1ffefdac Stack: 0x1f9bef20 Heap: 0x1f9bf000:0x1fecf000 U-Boot Environment: 0x000f0000:0x00100000 (SPI) Board configuration detected: mvBoardEgigaPhyInit in Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | SGMII | In-Band | egiga0 [PRIME] Hit any key to stop autoboot: 0 failed to read mcu workaround for reset address. Reset SCSI AHCI init for unit0 Target spinup took 0 ms. Target spinup took 0 ms. Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: Hitachi HDP72505 Rev: GM4O Type: Hard Disk Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Device 1: (1:0) Vendor: ATA Prod.: SAMSUNG HD502HI Rev: 1AG0 Type: Hard Disk Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Found 2 device(s). 3535504 bytes read in 142 ms (23.7 MiB/s) 14041 bytes read in 21 ms (652.3 KiB/s) 3329208 bytes read in 129 ms (24.6 MiB/s) ## Loading init Ramdisk from Legacy Image at 03000000 ... Image Name: HDL-AAX Created: 2022-06-18 12:56:29 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 3329144 Bytes = 3.2 MiB Load Address: 00000000 Entry Point: 00000000 ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x01000000 Loading Ramdisk to 1f690000, end 1f9bcc78 ... OK Loading Device Tree to 00ff9000, end 00fff6d8 ... OK Skipping Device Tree update ('fdt_skip_update' = yes) Limit DDR size at 3GB due to power of 2 requirement of Address decoding Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 3.10.70 (root@buildarmsrv) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 SMP Thu Nov 26 18:11:41 JST 2020 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), model: HDL-AA Memory policy: ECC disabled, Data cache writealloc PERCPU: Embedded 9 pages/cpu @c0e4e000 s12544 r8192 d16128 u36864 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyS0,115200 mtdparts=spi0.0:960k(boot),64k(env),-(system) initrd=0x3000040 rw root=/dev/md2 rootfstype=ext4 rw rootdelay=2 init=/lib/sysvinit/init PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 512MB = 512MB total Memory: 505868k/505868k available, 18420k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc08fa7a8 (9162 kB) .init : 0xc08fb000 - 0xc094e100 ( 333 kB) .data : 0xc0950000 - 0xc09b5d00 ( 408 kB) .bss : 0xc09b5d00 - 0xc0a440a4 ( 569 kB) Hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. NR_IRQS:16 nr_irqs:16 16 LSP version: linux-3.10.70-2015_T1.1p7 sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms L310 cache controller enabled l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B Console: colour dummy device 80x30 Calibrating delay loop... 2655.84 BogoMIPS (lpj=13279232) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0xc067e628 - 0xc067e680 mvebu-pmsu: Initializing Power Management Service Unit Initializing CPU Reset module CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (5311.69 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized mvebu-soc-id: MVEBU SoC ID=0x6811, Rev=0x4 xor: measuring software checksum speed arm4regs : 2366.000 MB/sec 8regs : 1630.000 MB/sec 32regs : 1658.400 MB/sec xor: using function: arm4regs (2366.000 MB/sec) pinctrl core: initialized pinctrl subsystem regulator-dummy: no parameters NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations irq: Cannot allocate irq_descs @ IRQ194, assuming pre-allocated irq: Cannot allocate irq_descs @ IRQ226, assuming pre-allocated bio: create slab <bio-0> at 0 raid6: int32x1 199 MB/s raid6: int32x2 274 MB/s raid6: int32x4 274 MB/s raid6: int32x8 302 MB/s raid6: using algorithm int32x8 (302 MB/s) raid6: using intx1 recovery algorithm vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered Switching to clocksource armada_370_xp_clocksource FS-Cache: Loaded NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... Freeing initrd memory: 3248K (df690000 - df9bc000) VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher FS-Cache: Netfs 'nfs' registered for caching NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Key type cifs.spnego registered Key type cifs.idmap registered NTFS driver 2.1.30 [Flags: R/O]. jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.22) SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled msgmni has been set to 994 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver gpio-mcu: gmcu_dev = f800000 (M: 248, m: 0) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A console [ttyS0] enabled brd: module loaded ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi0 : ahci_mv_platform scsi1 : ahci_mv_platform ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 m25p80 spi0.0: found w25q128, expected mx25l12805d m25p80 spi0.0: w25q128 (16384 Kbytes) 3 cmdlinepart partitions found on MTD device spi0.0 Creating 3 MTD partitions on "spi0.0": 0x000000000000-0x0000000f0000 : "boot" 0x0000000f0000-0x000000100000 : "env" 0x000000100000-0x000001000000 : "system" bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) errlp [mv_plat_data_get:4663] phy addr:0 errlp [mv_plat_data_get:4692] phy_mode:6 SoC: model = 0x6811, revision = 0x4 mvPncVirtBase = 0xe1400000, pncTcamSize = 1024 o 3 Giga ports supported o SKB recycle supported for SWF (Disabled) o NETA acceleration mode 4 o BM supported for CPU: 4 BM pools o PnC supported (Enabled) o RX Queue support: 8 Queues * 256 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Driver DEBUG statistics enabled port #0: is_sgmii=0, is_rgmii=1, phy_addr=0 o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 o Port 0 is connected to Linux netdevice o eth0, ifindex = 3, GbE port = 0 giga p=0: mtu=1500, mac=34:76:c5:xx:xx:05 (env config) libphy: orion_mdio_bus: probed phy int status:0x0, global phy int status:0x0 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1058000.usb: EHCI Host Controller orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 3.10.70 ehci_hcd usb usb1: SerialNumber: f1058000.usb hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: xHCI Host Controller usb usb2: Manufacturer: Linux 3.10.70 xhci-hcd usb usb2: SerialNumber: f10f0000.usb3 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: xHCI Host Controller usb usb3: Manufacturer: Linux 3.10.70 xhci-hcd usb usb3: SerialNumber: f10f0000.usb3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: xHCI Host Controller usb usb4: Manufacturer: Linux 3.10.70 xhci-hcd usb usb4: SerialNumber: f10f8000.usb3 hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: xHCI Host Controller usb usb5: Manufacturer: Linux 3.10.70 xhci-hcd usb usb5: SerialNumber: f10f8000.usb3 hub 5-0:1.0: USB hub found hub 5-0:1.0: 1 port detected usbcore: registered new interface driver usblp usbcore: registered new interface driver usb-storage usbcore: registered new interface driver ums-alauda usbcore: registered new interface driver ums-cypress usbcore: registered new interface driver ums-datafab usbcore: registered new interface driver ums_eneub6250 usbcore: registered new interface driver ums-freecom usbcore: registered new interface driver ums-isd200 usbcore: registered new interface driver ums-jumpshot usbcore: registered new interface driver ums-realtek usbcore: registered new interface driver ums-sddr09 usbcore: registered new interface driver ums-sddr55 usbcore: registered new interface driver ums-usbat ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-8: Hitachi HDP725050GLA360, GM4OA52A, max UDMA/133 ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) usb 2-1: new high-speed USB device number 2 using xhci-hcd ata2.00: ATA-7: SAMSUNG HD502HI, 1AG01118, max UDMA7 ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA Hitachi HDP72505 GM4O PQ: 0 ANSI: 5 usb 2-1: New USB device found, idVendor=05e3, idProduct=0608 usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 usb 2-1: Product: USB2.0 Hub hub 2-1:1.0: USB hub found hub 2-1:1.0: 4 ports detected ata2.00: configured for UDMA/133 sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD502HI 1AG0 PQ: 0 ANSI: 5 sd 1:0:0:0: Attached scsi generic sg1 type 0 sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sd 1:0:0:0: [sdb] Attached SCSI disk sda: sda1 sda2 sda3 sda4 sda5 sda6 sd 0:0:0:0: [sda] Attached SCSI disk mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 i2c /dev entries driver armada_thermal f10e4078.thermal: Overheat threshold between 92..107 orion_wdt: Initial timeout 171 sec md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 md: multipath personality registered for level -4 device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com dm_crypt using the OCF package. cpuidle: using governor ladder armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0) mvCesaInit: channels=2, session=640, queue=256 armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode cesadev_init(c092e7f8) hidraw: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver drop_monitor: Initializing network drop monitor service TCP: cubic registered NET: Registered protocol family 10 NET: Registered protocol family 17 Key type dns_resolver registered VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 NAS Controller 1.00 regulator-dummy: disabling mvebu-rtc f10a3800.rtc: setting system clock to 2022-06-18 12:58:35 UTC (1655557115) Freeing unused kernel memory: 332K (c08fb000 - c094e000) Loading, please wait... systemd-udevd[94]: starting version 215 Begin: Loading essential drivers ... done. ### probing disks ####################################################### MODEL: HDL2-AAX sda: sda1 sda2 sda3 sda4 sda5 sda6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 SATA: D1=/dev/sdb D2=/dev/sda USB: D1= D2= D3= ### check F/W installer ################################################# sda: sda1 sda2 sda3 sda4 sda5 sda6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sda: sda1 sda2 sda3 sda4 sda5 sda6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sda: sda1 sda2 sda3 sda4 sda5 sda6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sda: sda1 sda2 sda3 sda4 sda5 sda6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sda: sda1 sda2 sda3 sda4 sda5 sda6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 firminstall: probe: SATA: D1=/dev/sdb D2=/dev/sda USB: D1= D2= D3= NG_NO_USB_DEVICE ### check USB installer ################################################# sda: sda1 sda2 sda3 sda4 sda5 sda6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sda: sda1 sda2 sda3 sda4 sda5 sda6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sda: sda1 sda2 sda3 sda4 sda5 sda6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sda: sda1 sda2 sda3 sda4 sda5 sda6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sda: sda1 sda2 sda3 sda4 sda5 sda6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 usbinstall: probe: SATA: D1=/dev/sdb D2=/dev/sda USB: D1= D2= D3= NG_NO_USB_DEVICE ### check inEXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null) itialization ################################################ EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) ### assemble / volume ################################################### EXT4-fs (sdb4): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null) md: md2 stopped. md: bind<sda2> md: bind<sdb2> md/raid1:md2: active with 2 out of 3 mirrors md2: detected capacity change from 0 to 2145386496 md2: unknown partition table EXT4-fs (md2): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (sdb4): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null) md: md5 stopped. md: bind<sda5> md: bind<sdb5> md/raid1:md5: active with 2 out of 3 mirrors md5: detected capacity change from 0 to 1072693248 md5: unknown partition table Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevdsystemd-udevd[1120]: starting version 215 . ok [ ok ] Synthesizing the initial hotplug events...done. [ ok ] Waiting for /dev to be fully populated...done. [ ok ] Setting preliminary keymap...done. [ ok ] Assembling MD arrays...done (no arrays found in config file or automatically). [ ok ] Setting parameters of disc: (none). [....] Activating swap...Adding 1048572k swap on /dev/sdb3. Priority:-1 extents:1 across:1048572k Adding 1048572k swap on /dev/sda3. Priority:-2 extents:1 across:1048572k done. EXT4-fs (md2): re-mounted. Opts: (null) [warn] Creating compatibility symlink from /etc/mtab to /proc/mounts. ... (warning). [ ok ] Cleaning up temporary files... /tmp. [ ok ] Starting early crypto disks...done. [ ok ] Starting remaining crypto disks...done. [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. EXT4-fs (md5): mounted filesystem with ordered data mode. Opts: (null) fsevsync: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint [info] Loading kernel module fsevsync. [info] Loading kernel module vfsext. [info] Loading kernel module fuse. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. EXT4-fs (sdb4): mounted filesystem with ordered data mode. Opts: (null) [ ok ] Cleaning up temporary files... /tmp. mtdLoadDriver successful. ATTEMPT failed at mtdSetMacInterfaceCopperOnlyPhy:346 InitSystem fail,ret:1 App code started. Firmware version: 8.0.5.0 mtdLoadDriver successful. Firmware version: 8.0.5.0 [info] Setting console screen modes. setterm: cannot (un)set powersave mode: Inappropriate ioctl for device [ ok ] Setting up console font and keymap...done. [ ok ] Setting kernel variables ...done. [ ok ] Setting sensors limits. [....] Configuring network interfaces...RTNETLINK answers: Network is down run-parts: /etc/network/if-up.d/avahi-autoipd exited with return code 2 Failed to bring up eth0. RTNETLINK answers: No such process Stopping DHCPv6 client: dhcpc6. [ ok ] Starting web server: apache2. done. [ ok ] Starting rpcbind daemon.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. lm75 0-0049: hwmon1: sensor 'tmp75' i2c i2c-0: new_device: Instantiated device tmp75 at 0x49 pool #0: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added eth0: link up eth0: started eth0: link up, full duplex, speed 10 Mbps Not starting udftools packet writing: No devices listed in /etc/default/udftools [ ok ] Setting sysfs variables.... [ ok ] Starting uuid generator: uuidd. [ ok ] Starting system logging: syslog-ng. APFFind for AirPort Finder/Magical Finder Device [ ok ] Network Interface Plugging Daemon...start eth0...done. [ ok ] Starting web server: apache2. /bin/cat: /mnt/data/conf/network/device_uuid: No such file or directory [ ok ] Starting CUPS Bonjour daemon: cups-browsed. [ ok ] Starting MD monitoring service: mdadm --monitor. [ ok ] Starting hdl-aa-buttond: buttond. [ ok ] Starting SMP IRQ Balancer: irqbalance. [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting system message bus: dbus. [ ok ] saned disabled; edit /etc/default/saned. [....] Starting SNMP services:: snmpdEXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) Creating hostname and hostdesc. Set firmware update notification time. Set packages update notification time. Creating device UUID. [ ok ] Restarting dpwsd: dpwsd. EXT4-fs (sdb4): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null) XFS (sda6): Mounting Filesystem XFS (sda6): Ending clean mount XFS (sda6): Quotacheck needed: Please wait. XFS (sda6): Quotacheck: Done. XFS (sdb6): Mounting Filesystem XFS (sdb6): Ending clean mount XFS (sdb6): Quotacheck needed: Please wait. XFS (sdb6): Quotacheck: Done. XFS (sda6): Mounting Filesystem XFS (sda6): Ending clean mount XFS (sdb6): Mounting Filesystem XFS (sdb6): Ending clean mount Signature 3F33B879 - count 2 Signature 3F33B879 - count 2 vfsext signature - 3F33B879 EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (md2): re-mounted. Opts: (null) EXT4-fs (md2): re-mounted. Opts: (null) set count : 0 INIT: no more processes left in this runlevel
大破雑記帳 