bootlog
U-Boot 1.1.4 0.1.5 (Dec 13 2013 - 09:19:12)
U-boot DB120
DRAM[debug]:
sri
Wasp 1.2
wasp_ddr_initial_config(249): (16bit) ddr2 init
wasp_ddr_initial_config(426): Wasp ddr init done
Tap value selected = 0xf [0x0 - 0x1f]
Setting 0xb8116290 to 0x20402d0f
64 MB
cpu_pll_cfg: 0x40021380
cpu_pll_dither: 0xc00000
CFG_PLL_FREQ: 0x42
CFG_HZ : 280000000
CPU Clock: 560MHz DDR Data Rate: 450MHz DDR Clock: 225MHz
Top of RAM usable for U-Boot at: 84000000
Reserving 204k for U-Boot at: 83fcc000
Reserving 192k for malloc() at: 83f9c000
Reserving 44 Bytes for Board Info at: 83f9bfd4
Reserving 36 Bytes for Global Data at: 83f9bfb0
Reserving 128k for boot params() at: 83f7bfb0
Stack Pointer at: 83f7bf98
Now running in RAM - U-Boot at: 83fcc000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x17
flash size 8MB, sector count = 128
Flash: 8 MB
pci_init_board: PCIe PLL not set for 40MHz refclk
*** Warning *** : PCIe WLAN Module not found !!!
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
No valid address in Flash. Using fixed address
wasp reset mask:c03300
WASP ----> S17 PHY *
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
athrs17_reg_init: complete
eth0 up
eth0
Hit any key to stop autoboot: 0
## Booting image at 9f6d0000 ...
Image Name: Linux Kernel Image
Created: 2014-04-02 2:37:58 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 996687 Bytes = 973.3 kB
Load Address: 80002000
Entry Point: 801fa110
Verifying Checksum at 0x9f6d0040 ...OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 801fa110) ...
## Giving linux memsize in bytes, 67108864
Starting kernel ...
Booting Atheros AR934x
Linux version 2.6.31 (yian@yian-fedora11) (gcc version 4.3.3 (GCC) ) #2 Wed Apr 2 10:34:31 CST 2014
flash_size passed from bootloader = 8
arg 1: console=ttyS0,115200
arg 2: mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),2816k(rootfs1),1024k(uImage1),2816k(rootfs2),1024k(uImage2),64k(Config),64k(Rsv),64k(ART)
arg 3: init=/sbin/init
arg 4: bootsf=2
arg 5: root=/dev/mtdblock4
arg 6: rootfstype=squashfs
arg 7: uboot_ver=U-Boot_1.1.4_0.1.5
arg 8: mem=64M
CPU revision is: 0001974c (MIPS 74Kc)
ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 450 ahb 225
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS0,115200 mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),2816k(rootfs1),1024k(uImage1),2816k(rootfs2),1024k(uImage2),64k(Config),64k(Rsv),64k(ART) init=/sbin/init bootsf=2 root=/dev/mtdblock4 rootfstype=squashfs uboot_ver=U-Boot_1.1.4_0.1.5 mem=64M
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 62016k/65536k available (2033k kernel code, 3444k reserved, 579k data, 164k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
***** Warning *****: PCIe WLAN H/W not found !!!
bio: create slab at 0
SCSI subsystem initialized
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
fuse init (API version 7.12)
msgmni has been set to 121
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for lzma (lzma-generic)
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
brd: module loaded
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
9 cmdlinepart partitions found on MTD device ath-nor0
Creating 9 MTD partitions on "ath-nor0":
0x000000000000-0x000000040000 : "u-boot"
0x000000040000-0x000000050000 : "u-boot-env"
0x000000050000-0x000000310000 : "rootfs1"
0x000000310000-0x000000410000 : "uImage1"
0x000000410000-0x0000006d0000 : "rootfs2"
0x0000006d0000-0x0000007d0000 : "uImage2"
0x0000007d0000-0x0000007e0000 : "Config"
0x0000007e0000-0x0000007f0000 : "Rsv"
0x0000007f0000-0x000000800000 : "ART"
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
arch/mips/atheros/gpio.c (ath_simple_config_init) JUMPSTART_GPIO: 17
athwdt_init: Registering WDT success
ath_otp_init: Registering OTP success
ath_clksw_init: Registering Clock Switch Interface success
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Freeing unused kernel memory: 164k freed
init started: BusyBox v1.15.0 (2014-04-02 10:35:45 CST)
starting pid 32, tty '': '/etc/rc.d/rcS S boot'
/etc/rc.d/S05sysctl boot.
**** drop_caches_sysctl_handler: all done timer added ...****
/etc/rc.d/S06system boot.
Sun Jan 1 00:00:00 UTC 2012
/etc/rc.d/S07led boot.
/etc/rc.d/S08syslog boot.
/etc/rc.d/S10network boot.
ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
ATHR_GMAC: RX TASKLET - Pkts per Intr:100
ATHR_GMAC: Mac address for unit 0:bfff0000
ATHR_GMAC: ff:ff:ff:ff:ff:ff
ATHR_GMAC: Max segments per packet : 1
ATHR_GMAC: Max tx descriptor count : 384
ATHR_GMAC: Max rx descriptor count : 384
ATHR_GMAC: Mac capability flags : 2381
athr_gmac_ring_alloc Allocated 6144 at 0x83a8a000
athr_gmac_ring_alloc Allocated 6144 at 0x839fe000
WASP ----> S17 PHY *
Setting Drop CRC Errors, Pause Frames and Length Error frames
######## S17 SSDK init succeeded! ########
athrs17_reg_init:done
Setting PHY...
Phy setup Complete
Write Reg: 0x00000000: Oldval = 0x00001000 Newval = 0x00001a00
Write Reg: 0x00000000: Oldval = 0x00001000 Newval = 0x00001a00
Write Reg: 0x00000000: Oldval = 0x00001000 Newval = 0x00001a00
Write Reg: 0x00000000: Oldval = 0x00001000 Newval = 0x00001a00
Write Reg: 0x00000624: Oldval = 0x007f7f7f Newval = 0x007f7f7f
Write Reg: 0x00000010: Oldval = 0x40000000 Newval = 0x40000000
Write Reg: 0x00000004: Oldval = 0x07600000 Newval = 0x07600000
Write Reg: 0x0000000c: Oldval = 0x01000000 Newval = 0x01000000
Write Reg: 0x0000007c: Oldval = 0x0000007e Newval = 0x0000007e
Write Reg: 0x00000620: Oldval = 0x000004f0 Newval = 0x000004f0
Write Reg: 0x00000660: Oldval = 0x0014007e Newval = 0x0014027e
Write Reg: 0x0000066c: Oldval = 0x0014005d Newval = 0x0014027d
Write Reg: 0x00000678: Oldval = 0x0014005b Newval = 0x0014027b
Write Reg: 0x00000684: Oldval = 0x00140057 Newval = 0x00140277
Write Reg: 0x00000690: Oldval = 0x0014004f Newval = 0x0014026f
Write Reg: 0x0000069c: Oldval = 0x00140001 Newval = 0x0014025f
Write Reg: 0x00000420: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000428: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000430: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000438: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000440: Oldval = 0x00010001 Newval = 0x00010001
Write Reg: 0x00000448: Oldval = 0x00020001 Newval = 0x00020001
Write Reg: 0x00000424: Oldval = 0x00002040 Newval = 0x00002040
Write Reg: 0x0000042c: Oldval = 0x00001040 Newval = 0x00001040
Write Reg: 0x00000434: Oldval = 0x00001040 Newval = 0x00001040
Write Reg: 0x0000043c: Oldval = 0x00001040 Newval = 0x00001040
Write Reg: 0x00000444: Oldval = 0x00001040 Newval = 0x00001040
Write Reg: 0x0000044c: Oldval = 0x00001040 Newval = 0x00001040
Write Reg: 0x00000610: Oldval = 0x00000000 Newval = 0x001bd560
Write Reg: 0x00000614: Oldval = 0x00000000 Newval = 0x80010002
Write Reg: 0x00000610: Oldval = 0x00000000 Newval = 0x001b7fe0
Write Reg: 0x00000614: Oldval = 0x00000002 Newval = 0x80020002
Write Reg: 0x00000078: Oldval = 0x000005ee Newval = 0x00002400
Write Reg: 0x00000000: Oldval = 0x0000ffff Newval = 0x00001200
Write Reg: 0x00000004: Oldval = 0x00000de1 Newval = 0x000001e1
Write Reg: 0x00000009: Oldval = 0x00000200 Newval = 0x00000300
Write Reg: 0x00000000: Oldval = 0x0000ffff Newval = 0x00001200
Write Reg: 0x00000004: Oldval = 0x00000de1 Newval = 0x000001e1
Write Reg: 0x00000009: Oldval = 0x00000200 Newval = 0x00000300
Write Reg: 0x00000000: Oldval = 0x0000ffff Newval = 0x00001200
Write Reg: 0x00000004: Oldval = 0x00000de1 Newval = 0x000001e1
Write Reg: 0x00000009: Oldval = 0x00000200 Newval = 0x00000300
Write Reg: 0x00000000: Oldval = 0x0000ffff Newval = 0x00001200
Write Reg: 0x00000004: Oldval = 0x00000de1 Newval = 0x000001e1
Write Reg: 0x00000009: Oldval = 0x00000200 Newval = 0x00000300
Write Reg: 0x00000050: Oldval = 0xffb7ffb7 Newval = 0xffb7ffb7
Write Reg: 0x00000054: Oldval = 0xffb7ffb7 Newval = 0xffb7ffb7
Write Reg: 0x00000058: Oldval = 0xffb7ffb7 Newval = 0xffb7ffb7
Write Reg: 0x0000005c: Oldval = 0x03ffff00 Newval = 0x03ffff00
/etc/rc.d/S12nat boot.
/etc/rc.d/S30telnet boot.
/etc/rc.d/S35upnp boot.
/etc/rc.d/S39httpd boot.
/etc/rc.d/S42family boot.
starting pid 1888, tty '/dev/ttyS0': '/bin/sh --login'
BusyBox v1.15.0 (2014-04-02 10:35:45 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
#