タグ: WN-AC1600DGR2

WN-AC1600DGR2

花小金井のハードオフで見つけ、一度WRC-2533GSTのみ購入してこちらは見送ったものの、2度目行った際にやっぱりと購入。弄っていくためのメモ。
WN-AC1600DGRxはDGR – DGR3までハード的にはおおよそ同一と思われる(未確認)。

Switch

zone WAN LAN
port
(WN-AC1600DGR2)
インターネット LAN4 LAN3 LAN2 LAN1
port
(QCA8337N)
port5 port4 port3 port2 port1

MAC

  • LAN: xx:xx:xx:xx:xx:30
  • WAN: xx:xx:xx:xx:xx:32
  • 2.4G: xx:xx:xx:xx:xx:30
  • 5G: xx:xx:xx:xx:xx:31

U-Boot

  • help
    ath> help
    ?       - alias for 'help'
    autoscr - run script from memory
    base    - print or set address offset
    bdinfo  - print Board Info structure
    boot    - boot default, i.e., run 'bootcmd'
    bootd   - boot default, i.e., run 'bootcmd'
    bootelf - Boot from an ELF image in memory
    bootm   - boot application image from memory
    bootp   - boot image via network using BootP/TFTP protocol
    bootvx  - Boot vxWorks from an ELF image
    cmp     - memory compare
    coninfo - print console devices and information
    cp      - memory copy
    crc32   - checksum calculation
    dhcp    - invoke DHCP client to obtain IP/boot params
    echo    - echo args to console
    erase   - erase FLASH memory
    ethreg    - S26 PHY Reg rd/wr  utility
    exit    - exit script
    flinfo  - print FLASH memory information
    go      - start application at address 'addr'
    help    - print online help
    iminfo  - print header information for application image
    itest   - return true/false on integer compare
    loop    - infinite loop on address range
    md      - memory display
    mii     - MII utility commands
    mm      - memory modify (auto-incrementing)
    mtest   - simple RAM test
    mw      - memory write (fill)
    nfs     - boot image via network using NFS protocol
    nm      - memory modify (constant address)
    pci     - list and access PCI Configuration Space
    ping    - send ICMP ECHO_REQUEST to network host
    pll cpu-pll dither ddr-pll dither - Set to change CPU & DDR speed
    pll erase
    pll get
    printenv- print environment variables
    progmac - Set ethernet MAC addresses
    protect - enable or disable FLASH write protection
    rarpboot- boot image via network using RARP/TFTP protocol
    reset   - Perform RESET of the CPU
    run     - run commands in an environment variable
    saveenv - save environment variables to persistent storage
    setenv  - set environment variables
    sleep   - delay execution for some time
    test    - minimal test like /bin/sh
    tftpboot- boot image via network using TFTP protocol
    version - print monitor version
    

  • version
    ath> version
    
    U-Boot 0.1.4 (Aug  5 2013 - 10:36:02)
    

  • printenv
    ath> printenv
    bootargs=console=ttyS0,115200 root=31:02 rootfstype=squashfs,jffs2 init=/sbin/init mtdparts=ath-nor0:192k(u-boot),64k(u-boot-env),2752k(rootfs),1408k(uImage),64k(NVRAM),64k(ART)
    bootcmd=bootm 0x9f040000
    bootdelay=2
    baudrate=115200
    ethaddr="34:76:C5:35:11:30"
    ipaddr=192.168.99.9
    serverip=192.168.99.8
    sn=00043982W
    hw_ver=1.0.0
    hw_id=030A0046
    pro_id=000
    country=000
    domain=1
    wanaddr=34:76:C5:35:11:32
    wlanaddr=00:AA:BB:CC:DD:12
    snextra=BAL00043982W********
    bootfile=uImageWN-AC1600DGR
    dir=
    lu=tftp 0x80060000 ${dir}u-boot.bin&&erase 0x9f000000 +$filesize&&cp.b $fileaddr 0x9f000000 $filesize
    lf=tftp 0x80060000 ${dir}ap136${bc}-jffs2&&erase 0x9f050000 +0x630000&&cp.b $fileaddr 0x9f050000 $filesize
    lk=tftp 0x80060000 ${dir}vmlinux${bc}.lzma.uImage&&erase 0x9f680000 +$filesize&&cp.b $fileaddr 0x9f680000 $filesize
    ethact=eth0
    op_mode=0
    uboot_ver=0.1.4.13
    stdin=serial
    stdout=serial
    stderr=serial
    
    Environment size: 896/65532 bytes
    

Kernel

パスワード要求されるため、コンソールにログインできない。

  • bootlog (op_mode=0)
    U-Boot 0.1.4 (Aug  5 2013 - 10:36:02)
    Product Name: WN-AC1600DGR
    ap136 - Scorpion 1.0
    DRAM:128 MB
    Now running in RAM - U-Boot at: 87fc8000
    Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18
    Flash size 16MB, sector count = 256
    In:    serial
    Out:   serial
    Err:   serial
    reset_switch: 
    Multi Net:   
    
    ath_gmac_enet_initialize...
    
    athrs_sgmii_res_cal: cal value = 0x6
    No valid address in Flash. Using fixed address
    ath_gmac_enet_initialize: reset mask:c02200 
    Scorpion  ----> S17 PHY *
    : cfg1 0x80000000 cfg2 0x7114
    eth0: 00:03:7f:09:0b:ad
    athrs17_reg_init: SUPPORT_QCA8337 
    athrs17_reg_init: QCA8337 ID=1302
    athrs17_reg_init: complete
    eth0 up
    eth0
    athrs17_disable_all_port
    Setting 0x18116290 to 0x1830214f
    
    Please choose the operation: 
       1: Load system code to SDRAM via TFTP. 
       3: Boot system code via Flash (default).
                                                                                                                              0  
       
    3: System Boot system code via Flash.
    athrs17_set_portvlan_isolated complete
    ## Booting image at 9f040000 ...
       Image Name:   Linux Kernel Image
       Created:      2013-11-04   2:14:22 UTC
       Image Type:   MIPS Linux Kernel Image (lzma compressed)
       Data Size:    2881774 Bytes =  2.7 MB
       Load Address: 80002000
       Entry Point:  8024c7c0
       Verifying Checksum at 0x9f040040 ...OK
       Uncompressing Kernel Image ... OK
    
    Starting kernel ...
    
    Booting QCA955x
    Linux version 2.6.31 (root@localhost.localdomain) (gcc version 4.3.4 (Buildroot 2010.05) ) #2 Mon Nov 4 10:14:10 CST 2013
    flash_size passed from bootloader = 16
    arg 1: console=ttyS0,115200
    arg 2: root=31:02
    arg 3: rootfstype=squashfs,jffs2
    arg 4: init=/sbin/init
    arg 5: mtdparts=ath-nor0:192k(u-boot),64k(u-boot-env),2752k(rootfs),1408k(uImage),64k(NVRAM),64k(ART)
    arg 6: mem=128M
    CPU revision is: 00019750 (MIPS 74Kc)
    cpu apb ddr apb ath_sys_frequency: cpu 720 ddr 600 ahb 240
    Determined physical RAM map:
     memory: 02000000 @ 00000000 (usable)
    User-defined physical RAM map:
     memory: 08000000 @ 00000000 (usable)
    Initrd not found or empty - disabling initrd
    Zone PFN ranges:
      Normal   0x00000000 -> 0x00008000
    Movable zone start PFN for each node
    early_node_map[1] active PFN ranges
        0: 0x00000000 -> 0x00008000
    Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
    Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs,jffs2 init=/sbin/init mtdparts=ath-nor0:192k(u-boot),64k(u-boot-env),2752k(rootfs),1408k(uImage),64k(NVRAM),64k(ART) mem=128M 
    PID hash table entries: 512 (order: 9, 2048 bytes)
    Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
    Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
    Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
    Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
    Writing ErrCtl register=00000000
    Readback ErrCtl register=00000000
    Memory: 104888k/131072k available (2376k kernel code, 26020k reserved, 681k data, 7368k init, 0k highmem)
    NR_IRQS:128
    plat_time_init: plat time init done
    Calibrating delay loop... 359.42 BogoMIPS (lpj=718848)
    Mount-cache hash table entries: 512
    
    ****************ALLOC***********************
     Packet mem: 80a44bc0 (0xe00000 bytes)
    ********************************************
    
    NET: Registered protocol family 16
    ath_pcibios_init: bus 0
    ***** Warning PCIe 0 H/W not found !!!
    registering PCI controller with io_map_base unset
    ath_pcibios_init: bus 1
    ath_pcibios_init(232): PCI 1 CMD write: 0x356
    registering PCI controller with io_map_base unset
    bio: create slab  at 0
    SCSI subsystem initialized
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    pci 0000:01:00.0: PME# supported from D0 D1 D3hot
    pci 0000:01:00.0: PME# disabled
    pcibios_map_irq: IRQ 76 for bus 1
    NET: Registered protocol family 2
    IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
    TCP established hash table entries: 4096 (order: 3, 32768 bytes)
    TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
    TCP: Hash tables configured (established 4096 bind 4096)
    TCP reno registered
    NET: Registered protocol family 1
    ATH GPIOC major 0
    squashfs: version 4.0 (2009/01/31) Phillip Lougher
    NTFS driver 2.1.29 [Flags: R/O].
    JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
    fuse init (API version 7.12)
    msgmni has been set to 205
    alg: No test for stdrng (krng)
    io scheduler noop registered
    io scheduler deadline registered (default)
    Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
    serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
    console [ttyS0] enabled
    brd: module loaded
    loop: module loaded
    PPP generic driver version 2.4.2
    PPP Deflate Compression module registered
    PPP BSD Compression module registered
    PPP MPPE Compression module registered
    NET: Registered protocol family 24
    PPTP driver version 0.8.4
    IMQ driver loaded successfully.
            Hooking IMQ after NAT on PREROUTING.
            Hooking IMQ before NAT on POSTROUTING.
    usbcore: registered new interface driver asix
    Creating 9 MTD partitions on "ath-nor0":
    0x000000000000-0x000001000000 : "ALL"
    0x000000000000-0x000000030000 : "Bootloader"
    0x000000030000-0x000000040000 : "Config"
    0x000000040000-0x000000e90000 : "Kernel"
    0x000000300000-0x000000e90000 : "apps"
    0x000000e90000-0x000000f90000 : "manufacture"
    0x000000f90000-0x000000fa0000 : "backup"
    0x000000fa0000-0x000000ff0000 : "storage"
    0x000000ff0000-0x000001000000 : "caldata"
    usbmon: debugfs is not available
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    Port Status 1c000004 
    ath-ehci ath-ehci.0: ATH EHCI
    ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
    ehci_reset Intialize USB CONTROLLER in host mode: 13
    ehci_reset Port Status 1c000000 
    ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
    ehci_reset Intialize USB CONTROLLER in host mode: 13
    ehci_reset Port Status 1c000000 
    ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 1 port detected
    Port Status 1c000000 
    ath-ehci1 ath-ehci1.1: ATH EHCI
    ath-ehci1 ath-ehci1.1: new USB bus registered, assigned bus number 2
    ehci_reset Intialize USB CONTROLLER in host mode: 13
    ehci_reset Port Status 1c000000 
    ath-ehci1 ath-ehci1.1: irq 3, io mem 0x1b400000
    ehci_reset Intialize USB CONTROLLER in host mode: 13
    ehci_reset Port Status 1c000000 
    ath-ehci1 ath-ehci1.1: USB 2.0 started, EHCI 1.00
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 1 port detected
    Netfilter messages via NETLINK v0.30.
    ip_conntrack version 0.5.0 (3750 buckets, 30000 max 29800 max0 200 reserved) - 4 bytes per conntrack
    CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
    nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
    sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
    xt_time: kernel timezone is -0000
    ip_tables: (C) 2000-2006 Netfilter Core Team
    TCP cubic registered
    NET: Registered protocol family 17
    802.1Q VLAN Support v1.8 Ben Greear 
    All bugs added by David S. Miller 
    arch/mips/atheros/gpio_senao_qca955x.c (sn_init_irq) irq: 16
    arch/mips/atheros/gpio_senao_qca955x.c (sn_init_irq) irq: 17
    arch/mips/atheros/gpio_senao_qca955x.c (sn_init_irq) irq: 0
    arch/mips/atheros/gpio_senao_qca955x.c (sn_init_irq) irq: 15
    arch/mips/atheros/gpio_senao_qca955x.c (sn_init_irq) irq: 1
    arch/mips/atheros/gpio_senao_qca955x.c (sn_init_irq) irq: 19
    
    button_irq: simple_config callback.. ignorepb 1, jiffies 4294892560, gpio 19
    ath_otp_init: Registering OTP success
    Freeing unused kernel memory: 7368k freed
    init started: BusyBox v1.7.5 (2013-11-04 10:10:48 CST)
    starting pid 731, tty '/dev/console': '/sbin/config_init'
    mknod: /dev/ttyS0: File exists
    mknod: /dev/ttyS1: File exists
    Config Init version: 2.01.000.149 date: 2013/11/04
    Tue Jan  1 00:00:00 UTC 2013
    ln: /lib/./modules: File exists
    WAN connect type creat
    955x_GMAC: qca955x_gmac_attach
    955x_GMAC: qca955x_set_gmac_caps
    Currently in polling mode unit0
    mac:0 Registering S17....
    qca955x_GMAC: RX TASKLET - Pkts per Intr:100
    qca955x_GMAC: Max segments per packet :   1
    qca955x_GMAC: Max tx descriptor count :   5
    qca955x_GMAC: Max rx descriptor count :   128
    qca955x_GMAC: Mac capability flags    :   2A00
    starting pid 792, tty '/dev/ttyS0': '/sbin/config_term'
    ************************************************************************
    *                             WN-AC1600DGR                             *
    ************************************************************************
    
    KernelApp/Ramdisk Ver:2.01.000.149                       Date:2013/11/04
    password: +HWT
    -HWT
    HTC Service:0x0300 ep:1 TX flow control disabled
    VAP device ath0 created 
    VAP device ath1 created 
    VAP device ath2 created 
    VAP device ath3 created
    

  • bootlog (op_mode=1)
    U-Boot 0.1.4 (Aug  5 2013 - 10:36:02)
    Product Name: WN-AC1600DGR
    ap136 - Scorpion 1.0
    DRAM:128 MB
    Now running in RAM - U-Boot at: 87fc8000
    Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18
    Flash size 16MB, sector count = 256
    In:    serial
    Out:   serial
    Err:   serial
    reset_switch: 
    Multi Net:   
    
    ath_gmac_enet_initialize...
    
    athrs_sgmii_res_cal: cal value = 0x6
    No valid address in Flash. Using fixed address
    ath_gmac_enet_initialize: reset mask:c02200 
    Scorpion  ----> S17 PHY *
    : cfg1 0x80000000 cfg2 0x7114
    eth0: 00:03:7f:09:0b:ad
    athrs17_reg_init: SUPPORT_QCA8337 
    athrs17_reg_init: QCA8337 ID=1302
    athrs17_reg_init: complete
    eth0 up
    eth0
    athrs17_disable_all_port
    Setting 0x18116290 to 0x1830214f
    
    Please choose the operation: 
       1: Load system code to SDRAM via TFTP. 
       3: Boot system code via Flash (default).
                                                                                                                              0  
       
    3: System Boot system code via Flash.
    athrs17_set_portvlan_isolated complete
    ## Booting image at 9f040000 ...
       Image Name:   Linux Kernel Image
       Created:      2013-11-04   2:14:22 UTC
       Image Type:   MIPS Linux Kernel Image (lzma compressed)
       Data Size:    2881774 Bytes =  2.7 MB
       Load Address: 80002000
       Entry Point:  8024c7c0
       Verifying Checksum at 0x9f040040 ...OK
       Uncompressing Kernel Image ... OK
    
    Starting kernel ...
    
    Booting QCA955x
    Linux version 2.6.31 (root@localhost.localdomain) (gcc version 4.3.4 (Buildroot 2010.05) ) #2 Mon Nov 4 10:14:10 CST 2013
    flash_size passed from bootloader = 16
    arg 1: console=ttyS0,115200
    arg 2: root=31:02
    arg 3: rootfstype=squashfs,jffs2
    arg 4: init=/sbin/init
    arg 5: mtdparts=ath-nor0:192k(u-boot),64k(u-boot-env),2752k(rootfs),1408k(uImage),64k(NVRAM),64k(ART)
    arg 6: mem=128M
    CPU revision is: 00019750 (MIPS 74Kc)
    cpu apb ddr apb ath_sys_frequency: cpu 720 ddr 600 ahb 240
    Determined physical RAM map:
     memory: 02000000 @ 00000000 (usable)
    User-defined physical RAM map:
     memory: 08000000 @ 00000000 (usable)
    Initrd not found or empty - disabling initrd
    Zone PFN ranges:
      Normal   0x00000000 -> 0x00008000
    Movable zone start PFN for each node
    early_node_map[1] active PFN ranges
        0: 0x00000000 -> 0x00008000
    Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
    Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs,jffs2 init=/sbin/init mtdparts=ath-nor0:192k(u-boot),64k(u-boot-env),2752k(rootfs),1408k(uImage),64k(NVRAM),64k(ART) mem=128M 
    PID hash table entries: 512 (order: 9, 2048 bytes)
    Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
    Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
    Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
    Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
    Writing ErrCtl register=00000000
    Readback ErrCtl register=00000000
    Memory: 104888k/131072k available (2376k kernel code, 26020k reserved, 681k data, 7368k init, 0k highmem)
    NR_IRQS:128
    plat_time_init: plat time init done
    Calibrating delay loop... 359.42 BogoMIPS (lpj=718848)
    Mount-cache hash table entries: 512
    
    ****************ALLOC***********************
     Packet mem: 80a44bc0 (0xe00000 bytes)
    ********************************************
    
    NET: Registered protocol family 16
    ath_pcibios_init: bus 0
    ***** Warning PCIe 0 H/W not found !!!
    registering PCI controller with io_map_base unset
    ath_pcibios_init: bus 1
    ath_pcibios_init(232): PCI 1 CMD write: 0x356
    registering PCI controller with io_map_base unset
    bio: create slab  at 0
    SCSI subsystem initialized
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    pci 0000:01:00.0: PME# supported from D0 D1 D3hot
    pci 0000:01:00.0: PME# disabled
    pcibios_map_irq: IRQ 76 for bus 1
    NET: Registered protocol family 2
    IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
    TCP established hash table entries: 4096 (order: 3, 32768 bytes)
    TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
    TCP: Hash tables configured (established 4096 bind 4096)
    TCP reno registered
    NET: Registered protocol family 1
    ATH GPIOC major 0
    squashfs: version 4.0 (2009/01/31) Phillip Lougher
    NTFS driver 2.1.29 [Flags: R/O].
    JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
    fuse init (API version 7.12)
    msgmni has been set to 205
    alg: No test for stdrng (krng)
    io scheduler noop registered
    io scheduler deadline registered (default)
    Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
    serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
    console [ttyS0] enabled
    brd: module loaded
    loop: module loaded
    PPP generic driver version 2.4.2
    PPP Deflate Compression module registered
    PPP BSD Compression module registered
    PPP MPPE Compression module registered
    NET: Registered protocol family 24
    PPTP driver version 0.8.4
    IMQ driver loaded successfully.
            Hooking IMQ after NAT on PREROUTING.
            Hooking IMQ before NAT on POSTROUTING.
    usbcore: registered new interface driver asix
    Creating 9 MTD partitions on "ath-nor0":
    0x000000000000-0x000001000000 : "ALL"
    0x000000000000-0x000000030000 : "Bootloader"
    0x000000030000-0x000000040000 : "Config"
    0x000000040000-0x000000e90000 : "Kernel"
    0x000000300000-0x000000e90000 : "apps"
    0x000000e90000-0x000000f90000 : "manufacture"
    0x000000f90000-0x000000fa0000 : "backup"
    0x000000fa0000-0x000000ff0000 : "storage"
    0x000000ff0000-0x000001000000 : "caldata"
    usbmon: debugfs is not available
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    Port Status 1c000004 
    ath-ehci ath-ehci.0: ATH EHCI
    ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
    ehci_reset Intialize USB CONTROLLER in host mode: 13
    ehci_reset Port Status 1c000000 
    ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
    ehci_reset Intialize USB CONTROLLER in host mode: 13
    ehci_reset Port Status 1c000000 
    ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 1 port detected
    Port Status 1c000000 
    ath-ehci1 ath-ehci1.1: ATH EHCI
    ath-ehci1 ath-ehci1.1: new USB bus registered, assigned bus number 2
    ehci_reset Intialize USB CONTROLLER in host mode: 13
    ehci_reset Port Status 1c000000 
    ath-ehci1 ath-ehci1.1: irq 3, io mem 0x1b400000
    ehci_reset Intialize USB CONTROLLER in host mode: 13
    ehci_reset Port Status 1c000000 
    ath-ehci1 ath-ehci1.1: USB 2.0 started, EHCI 1.00
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 1 port detected
    Netfilter messages via NETLINK v0.30.
    ip_conntrack version 0.5.0 (3750 buckets, 30000 max 29800 max0 200 reserved) - 4 bytes per conntrack
    CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
    nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
    sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
    xt_time: kernel timezone is -0000
    ip_tables: (C) 2000-2006 Netfilter Core Team
    TCP cubic registered
    NET: Registered protocol family 17
    802.1Q VLAN Support v1.8 Ben Greear 
    All bugs added by David S. Miller 
    arch/mips/atheros/gpio_senao_qca955x.c (sn_init_irq) irq: 16
    arch/mips/atheros/gpio_senao_qca955x.c (sn_init_irq) irq: 17
    arch/mips/atheros/gpio_senao_qca955x.c (sn_init_irq) irq: 0
    arch/mips/atheros/gpio_senao_qca955x.c (sn_init_irq) irq: 15
    arch/mips/atheros/gpio_senao_qca955x.c (sn_init_irq) irq: 1
    arch/mips/atheros/gpio_senao_qca955x.c (sn_init_irq) irq: 19
    
    button_irq: simple_config callback.. ignorepb 1, jiffies 4294892560, gpio 19
    ath_otp_init: Registering OTP success
    Freeing unused kernel memory: 7368k freed
    init started: BusyBox v1.7.5 (2013-11-04 10:10:48 CST)
    starting pid 731, tty '/dev/console': '/sbin/config_init'
    mknod: /dev/ttyS0: File exists
    mknod: /dev/ttyS1: File exists
    Config Init version: 2.01.000.149 date: 2013/11/04
    Tue Jan  1 00:00:00 UTC 2013
    ln: /lib/./modules: File exists
    WAN connect type creat
    955x_GMAC: qca955x_gmac_attach
    955x_GMAC: qca955x_set_gmac_caps
    Currently in polling mode unit0
    mac:0 Registering S17....
    qca955x_GMAC: RX TASKLET - Pkts per Intr:100
    qca955x_GMAC: Max segments per packet :   1
    qca955x_GMAC: Max tx descriptor count :   5
    qca955x_GMAC: Max rx descriptor count :   128
    qca955x_GMAC: Mac capability flags    :   2A00
    starting pid 790, tty '/dev/ttyS0': '/sbin/config_term'
    ************************************************************************
    *                             WN-AC1600DGR                             *
    ************************************************************************
    
    KernelApp/Ramdisk Ver:2.01.000.149                       Date:2013/11/04
    Application Ver:2.01.000.149             Date:2013/11/04
    
    cmd [mkdir -p /appscore]
    cmd [cp /apps/appscore.sqsh /appscore.sqsh]
    cmd [mount -o loop -t squashfs -r /appscore.sqsh /appscore]
    cmd [test -d /appscore/sbin && ln -sf /appscore/sbin/* /sbin]
    cmd [test -f /appscore/sbin/httpd && ln -sf /appscore/sbin/httpd /sbin/httpsd]
    cmd [test -d /appscore/lib && ln -sf /appscore/lib/* /lib]
    cmd [rm -rf /lib/modules/2.6.31]
    cmd [mkdir -p /lib/modules/2.6.31/kernel]
    cmd [ln -s /apps/lib/modules/2.6.31/kernel/* /lib/modules/2.6.31/kernel]
    cmd [cat /apps/lib/modules/2.6.31/modules.dep >> /lib/modules/2.6.31/modules.dep]
    password: cmd [ln -s /apps/sbin/* /sbin]
    ln: /sbin/apps_init: File exists
    ln: /sbin/factory_apps_init: File exists
    ln: /sbin/opmode.sh: File exists
    cmd [rm /sbin/utelnetd]
    cmd [ls /apps/bin/* 1>/dev/null 2>/dev/null && ln -s /apps/bin/* /bin]
    cmd [ls /apps/usr/sbin/* 1>/dev/null 2>/dev/null && ln -s /apps/usr/sbin/* /usr/sbin]
    cmd [ls /apps/usr/bin/* 1>/dev/null 2>/dev/null && ln -s /apps/usr/bin/* /usr/bin]
    cmd [ls /apps/usr/local/* 1>/dev/null 2>/dev/null && ln -s /apps/usr/local/* /usr/local]
    cmd [ls /apps/usr/lib/* 1>/dev/null 2>/dev/null && ln -s /apps/usr/lib/* /usr/lib]
    cmd [mkdir -p /etc/udhcpc]
    cmd [ln -s /apps/etc/udhcpc/* /etc/udhcpc]
    cmd [mkdir -p /usr/lib/tc]
    cmd [ls /apps/usr/lib/tc/* 1>/dev/null 2>/dev/null && ln -s /apps/usr/lib/tc/* /usr/lib/tc]
    cmd [ln -s /apps/etc/xml /etc/xml]
    cmd [/sbin/apcfg_init]
    createShareMem keyid 7001 shmId 0
    Set Str value fail but len not in 1 to 32
    checkpApCfg i=28 [ap2ssid]
    Set Str value fail but len not in 1 to 32
    checkpApCfg i=46 [ap3ssid]
    checkpApCfg error!!
    cmd [/sbin/sysconfd -dddd &]
    cmd [mkdir -p /mnt/sysconfd]
    cmd [ln -s /mnt/sysconfd /var/sysconfd]
    MSGQ_GETID: Cannot get message queue for key[fwmanager]!
    MSGQ_CREATE: create message queue for key[fwmanager], msgQ Id 0
    CTRL_INTERFACE:[/var/sysconfd_if]  CTRL_INTERFACE_IF:[if0]
    
    System Monitoring
    cmd [/sbin/sysconf_cli -t 60 sysinit]
    *********************************************************************
    Initializing system environment
    Setting up /tmp directory ...
    cmd [chmod 777 /tmp]
    Setting up loopback device ...
    cmd [ifconfig lo up 127.0.0.1 netmask 255.0.0.0]
    ***************************************************
    Radio_1 is in   Access Point[0]
    Radio_2 is in   Access Point[0]
    System is in    AP Router[0]
    ***************************************************
    SEM_GETID got id -1
    cmd [sysctl -w net.ipv4.netfilter.ip_conntrack_max=30000]
    net.ipv4.netfilter.ip_conntrack_max = 30000
    cmd [sysctl -w net.ipv4.netfilter.ip_conntrack_icmp_timeout=30]
    net.ipv4.netfilter.ip_conntrack_icmp_timeout = 30
    cmd [sysctl -w net.ipv4.netfilter.ip_conntrack_udp_timeout=600]
    net.ipv4.netfilter.ip_conntrack_udp_timeout = 600
    cmd [sysctl -w net.ipv4.netfilter.ip_conntrack_udp_timeout_stream=600]
    net.ipv4.netfilter.ip_conntrack_udp_timeout_stream = 600
    cmd [sysctl -w net.ipv4.netfilter.ip_conntrack_tcp_timeout_established=14400]
    net.ipv4.netfilter.ip_conntrack_tcp_timeout_established = 14400
    cmd [sysctl -w kernel.shmmax=3145728]
    kernel.shmmax = 3145728
    cmd [sysctl -w vm.dirty_expire_centisecs=100]
    vm.dirty_expire_centisecs = 100
    cmd [sysctl -w vm.dirty_background_ratio=1]
    vm.dirty_background_ratio = 1
    cmd [sysctl -w vm.dirty_expire_centisecs=300]
    vm.dirty_expire_centisecs = 300
    cmd [sysctl -w vm.dirty_ratio=10]
    vm.dirty_ratio = 10
    cmd [sysctl -w vm.vfs_cache_pressure=150]
    vm.vfs_cache_pressure = 150
    cmd [sysctl -w vm.min_free_kbytes=10240]
    vm.min_free_kbytes = 10240
    cmd [sysctl -w vm.overcommit_memory=0]
    vm.overcommit_memory = 0
    cmd [sysctl -w vm.swappiness=0]
    vm.swappiness = 0
    cmd [sysctl -w fs.file-max=2048]
    fs.file-max = 2048
    Mac: 0, rtcTime:1356998402
    cmd [echo 1356998402 > /dev/urandom]
    cmd [dmesg |grep "CPU: " > /var/cpumhz]
    Open file err: /var/cpumhz!
    Starting system logging daemon ...cmd [echo JST-9 > /etc/TZ]
    cmd [date -s 2012.1.1-0:0:0]
    Sun Jan  1 00:00:00 JST 2012
    cmd [echo JST-9 > /etc/TZ]
    cmd [logserver -d]
    connect: No such file or directory
    -----> LOG : TIME, Daylight saving status: Disable
    -----> LOG : TIME, Local time=2012/01/01 00:00:00
    cmd [/sbin/klogd]
    sh: /sbin/klogd: not found
    cmd [/sbin/logserver &]
    cmd [/sbin/syslogd -k 0 -R 192.168.0.250]
    mask = 0
    cmd [/sbin/logserver -t "Start Log Message Service!" ]
    /tmp/log_tmp open error!
    -----> LOG : SYS, Application Version: 2.01
    OK
    Setting up Ethernet devices ...To set s17 LOOKUP_CTRL_REG registers, flag 0 
    
    cmd [/sbin/ifcathr_gmac_ring_alloc Allocated 80 at 0x86d559e0
    onfig eth0 up]
    athr_gmac_ring_alloc Allocated 2048 at 0x805db800
    device id=1302
    /proc/qca_switch/nf_athrs17_hnat is created
    /proc/qca_switch/nf_athrs17_hnat_wan_type is created
    /proc/qca_switch/nf_athrs17_hnat_ppp_id is created
    /proc/qca_switch/nf_athrs17_hnat_udp_thresh is created
    /proc/qca_switch/nf_athrs17_hnat_wan_ip is created
    /proc/qca_switch/nf_athrs17_hnat_ppp_peer_ip is created
    /proc/qca_switch/nf_athrs17_hnat_ppp_peer_mac is created
    /proc/qca_switch/nf_athrs17_hnat_wan_mac is created
    Registering IPv6 hooks... 
    Adding ACL rules 15 - upnp_ssdp_add_acl_rules
    ACL is not yet enabled. Enabling... 
    Adding ACL rules 7 - ipv6_snooping_solicted_node_add_acl_rules
    Adding ACL rules 11 - ipv6_snooping_sextuple0_group_add_acl_rules
    Adding ACL rules 13 - ipv6_snooping_quintruple0_1_group_add_acl_rules
    Hello, nat helper module for 1.1!
    
    ######## S17 SSDK init succeeded! ########
    ### s17 : set 0x610=0x001bd560 
    ### s17 : set 0x614=0x80010002 
    ### s17 : set 0x610=0x001b7fe0 
    ### s17 : set 0x614=0x80020002 
    _athrs17_mac0_intf done
    athrs17_reg_init:done
    S17_P0PAD_MODE_REG 0x87680000
    athrs17_reg_init:done
    955x_GMAC: eth0 in RGMII MODE
    Scorpion -----> S17 PHY
    Setting Drop CRC Errors, Pause Frames and Length Error frames 
    Setting PHY...
    Phy setup Complete
    To set s17 LOOKUP_CTRL_REG registers, flag 1 
    cmd [vconfig add eth0 1]
    cmd [vconfig add eth0 2]
    cmd [ifconfig eth0.1 0.0.0.0]
    cmd [ifconfig eth0.2 0.0.0.0]
    cmd [/sbin/ifconfig eth0.1 down]
    cmd [/sbin/ifconfig eth0.1 hw ether 34:76:C5:35:11:30 
    ]
    cmd [/sbin/ifconfig eth0.1 up]
    device eth0 entered promiscuous mode
    cmd [/sbin/ifconfig eth0.2 down]
    cmd [/sbin/ifconfig eth0.2 hw ether 34:76:C5:35:11:32 
    ]
    cmd [/sbin/ifconfig eth0.2 up]
    OK
    Configuring Bridge device ...          -----> LOG : BR, start
    cmd [brctl addbr br0]
    cmd [/sbin/ifconfig br0 down]
    cmd [/sbin/ifconfig br0 hw ether 34:76:C5:35:11:30 
    ]
    cmd [/sbin/ifconfig br0 up]
    cmd [brctl setfd br0 0.1]
    cmd [brctl setbridgeprio br0 32768]
    OK
    Setting the host&domain name ...Finished.
    Configuring net ...          cmd [sysctl -p /etc/sysctl.conf]
    net.ipv4.neigh.default.proxy_qlen = 96
    net.ipv4.neigh.default.unres_qlen = 6
    net.ipv4.ip_local_port_range = 32768 65535
    net.ipv4.tcp_timestamps = 0
    net.ipv4.tcp_sack = 0
    net.ipv4.tcp_window_scaling = 0
    net.ipv4.tcp_rmem = 1048576 1048576 1048576
    net.ipv4.tcp_wmem = 1048576 1048576 1048576
    net.ipv4.tcp_mem = 1048576 1048576 1048576
    net.ipv4.tcp_ecn = 0
    net.ipv4.tcp_reordering = 3
    net.ipv4.tcp_fack = 0
    net.ipv4.icmp_echo_ignore_broadcasts = 1
    net.ipv4.icmp_ignore_bogus_error_responses = 1
    net.ipv4.icmp_echo_ignore_all = 0
    net.ipv4.tcp_max_syn_backlog = 2048
    net.ipv4.tcp_syncookies = 1
    net.ipv4.tcp_fin_timeout = 30
    net.ipv4.tcp_retries2 = 15
    net.ipv4.tcp_retries1 = 3
    net.ipv4.tcp_rfc1337 = 1
    net.ipv4.tcp_keepalive_time = 3600
    net.ipv4.tcp_synack_retries = 5
    net.ipv4.tcp_syn_retries = 5
    net.core.somaxconn = 512
    net.core.netdev_max_backlog = 1024
    net.core.dev_weight = 64
    net.core.optmem_max = 1048576
    net.core.rmem_default = 1048576
    net.core.wmem_default = 1048576
    net.core.rmem_max = 1048576
    net.core.wmem_max = 1048576
    cmd [(for i in `ls /proc/sys/net/ipv4/conf/*/accept_source_route`; do              echo 0 > $i;            done) ; (for i in `ls /proc/sys/net/ipv4/conf/*/accept_redirects`; do              echo 0 > $i;            done) ; (for i in `ls /proc/sys/net/ipv4/conf/*/send_redirects`; do              echo 0 > $i;            done) ; (for i in `ls /proc/sys/net/ipv4/conf/*/rp_filter`; do              echo 1 > $i;            done) ; (for i in `ls /proc/sys/net/ipv4/conf/*/log_martians`; do              echo 1 > $i;            done) ; ]
    cmd [echo 0 > /proc/sys/net/ipv4/conf/br0/rp_filter]
    OK
    cmd [mkdir -p /etc/ipv4ll]
    cmd [ln -s /apps/etc/ipv4ll/* /etc/ipv4ll/.]
    Configuring LAN device ...          -----> LOG : LAN, start
    cmd [/sbin/ifconfig br0 down]
    cmd [/sbin/ifconfig eth0.1 0.0.0.0 up]
    cmd [brctl addif br0 eth0.1]
    device eth0.1 entered promiscuous mode
    cmd [/sbin/ifconfig br0 192.168.0.1 netmask 255.255.255.0]
    br0: port 1(eth0.1) entering learning state
    cmd [brctl stp br0 0]
    cmd [route add -net 239.0.0.0 netmask 255.0.0.0 br0]
    OK
    
    
    #############################################
    Initialize Radio setting ... OK
    Configuring radio1 setting ... 
    Configuring Atheros device index:0... FCMD[insmod /lib/adf.ko]
    FCMD[insmod /lib/asf.ko]
    FCMD[insmod /lib/ath_hal.ko]
    FCMD[insmod /lib/ath_rate_atheros.ko]
    FCMD[insmod /lib/ath_dfs.ko]
    FCMD[insmod /lib/ath_dev.ko]
    FCMD[insmod /lib/umac.ko]
    FCMD[ln -s /sbin/hostapd /sbin/hostapd1]
    FCMD[ln -s /sbin/hostapd /sbin/hostapd2]
    wifiname=wifi0 , macaddr=34:76:C5:35:11:30FCMD[ifconfig wifi0 hw ether 34:76:C5:35:11:30]
    FCMD[iwpriv wifi0 setCountryID 4015]
    FCMD[wlanconfig ath0 create wlandev wifi0 wlanmode ap ]
    FCMD[wlanconfig ath1 create wlandev wifi0 wlanmode ap ]
    FCMD[wlanconfig ath2 create wlandev wifi0 wlanmode ap ]
    FCMD[iwpriv wifi0 rxchainmask 3]
    FCMD[iwpriv wifi0 txchainmask 3]
    FCMD[iwpriv wifi0 burst 1]
    FCMD[ifconfig etbr0: port 1(eth0.1) entering forwarding state
    h0 txqueuelen 10000]
    FCMD[iwpriv ath0 mode 11nght40minus]
    FCMD[iwpriv ath1 mode 11nght40minus]
    FCMD[iwpriv ath2 mode 11nght40minus]
    FCMD[iwpriv ath0 cwmenable 1]
    FCMD[iwpriv ath0 chwidth 1]
    FCMD[iwpriv ath1 chwidth 1]
    FCMD[iwpriv ath2 chwidth 1]
    FCMD[iwpriv ath0 disablecoext 1]
    FCMD[sleep 1]
    -----> LOG : WLAN1, Wireless mode = 802.11 2.4G b/g/n
    FCMD[iwpriv ath0 ap_bridge 1]
    FCMD[iwpriv ath0 bssid_bridge 1]
    FCMD[iwpriv ath1 ap_bridge 1]
    FCMD[iwpriv ath1 bssid_bridge 0]
    FCMD[iwpriv ath2 ap_bridge 1]
    FCMD[iwpriv ath2 bssid_bridge 1]
    FCMD[iwconfig ath0 essid "AirPort04400"]
    -----> LOG : WLAN1, SSID1 = AirPort04400
    FCMD[iwconfig ath1 essid "Guest04400"]
    -----> LOG : WLAN1, SSID2 = Guest04400
    FCMD[iwconfig ath2 essid "Copy04400"]
    -----> LOG : WLAN1, SSID3 = Copy04400
    FCMD[iwconfig ath0 channel 11]
    FCMD[iwconfig ath1 channel 11]
    FCMD[iwconfig ath2 channel 11]
    -----> LOG : WLAN1, Channel = 11
    FCMD[iwpriv ath0 maxsta 127]
    FCMD[iwpriv ath0 bintval 100]
    -----> LOG : WLAN1, Beacon Interval = 100(ms)
    FCMD[iwpriv ath0 dtim_period 1]
    FCMD[iwpriv ath1 dtim_period 1]
    FCMD[iwpriv ath2 dtim_period 1]
    -----> LOG : WLAN1, DTIM period = 1
    FCMD[iwpriv ath0 shpreamble 0]
    -----> LOG : WLAN1, Preamble = Long Preamble
    FCMD[iwconfig ath0 rts 2347]
    FCMD[iwconfig ath1 rts 2347]
    FCMD[iwconfig ath2 rts 2347]
    FCMD[iwpriv ath0 protmode 2]
    FCMD[iwpriv ath0 countryie 1]
    FCMD[iwpriv ath0 hide_ssid 0]
    FCMD[iwpriv ath1 hide_ssid 0]
    FCMD[iwpriv ath2 hide_ssid 0]
    FCMD[iwpriv ath0 wmm 1]
    FCMD[iwpriv ath1 wmm 1]
    FCMD[iwpriv ath2 wmm 1]
    FCMD[iwpriv ath0 cwmin 0 0 4]
    FCMD[iwpriv ath0 cwmin 1 0 4]
    FCMD[iwpriv ath0 cwmin 2 0 3]
    FCMD[iwpriv ath0 cwmin 3 0 2]
    FCMD[iwpriv ath0 cwmax 0 0 6]
    FCMD[iwpriv ath0 cwmax 1 0 10]
    FCMD[iwpriv ath0 cwmax 2 0 4]
    FCMD[iwpriv ath0 cwmax 3 0 3]
    FCMD[iwpriv ath0 aifs 0 0 3]
    FCMD[iwpriv ath0 aifs 1 0 7]
    FCMD[iwpriv ath0 aifs 2 0 1]
    FCMD[iwpriv ath0 aifs 3 0 1]
    FCMD[iwpriv ath0 txoplimit 0 0 0]
    FCMD[iwpriv ath0 txoplimit 1 0 0]
    FCMD[iwpriv ath0 txoplimit 2 0 94]
    FCMD[iwpriv ath0 txoplimit 3 0 47]
    FCMD[iwpriv ath0 cwmin 0 1 4]
    FCMD[iwpriv ath0 cwmin 1 1 4]
    FCMD[iwpriv ath0 cwmin 2 1 3]
    FCMD[iwpriv ath0 cwmin 3 1 2]
    FCMD[iwpriv ath0 cwmax 0 1 10]
    FCMD[iwpriv ath0 cwmax 1 1 10]
    FCMD[iwpriv ath0 cwmax 2 1 4]
    FCMD[iwpriv ath0 cwmax 3 1 3]
    FCMD[iwpriv ath0 aifs 0 1 3]
    FCMD[iwpriv ath0 aifs 1 1 7]
    FCMD[iwpriv ath0 aifs 2 1 2]
    FCMD[iwpriv ath0 aifs 3 1 2]
    FCMD[iwpriv ath0 txoplimit 0 1 0]
    FCMD[iwpriv ath0 txoplimit 1 1 0]
    FCMD[iwpriv ath0 txoplimit 2 1 94]
    FCMD[iwpriv ath0 txoplimit 3 1 47]
    FCMD[iwpriv ath0 acm 0 1 0]
    FCMD[iwpriv ath0 acm 1 1 0]
    FCMD[iwpriv ath0 acm 2 1 0]
    FCMD[iwpriv ath0 acm 3 1 0]
    FCMD[iwpriv ath0 noackpolicy 0 0 0]
    FCMD[iwpriv ath0 noackpolicy 1 0 0]
    FCMD[iwpriv ath0 noackpolicy 2 0 0]
    FCMD[iwpriv ath0 noackpolicy 3 0 0]
    FCMD[iwpriv ath0 mcastenhance 2]
    FCMD[iwpriv ath0 mcast_rate 300000]
    FCMD[iwpriv ath1 mcastenhance 2]
    FCMD[iwpriv ath1 mcast_rate 300000]
    FCMD[iwpriv ath2 mcastenhance 2]
    FCMD[iwpriv ath2 mcast_rate 300000]
    FCMD[iwpriv wifi0 set_swapled 1]
    FCMD[killall hostapd1]
    Encryption using WEP ...      
    FCMD[iwconfig ath0 key off]
    Encryption using WEP ...      
    FCMD[iwconfig ath1 key off]
    Encryption using WEP ...      
    FCMD[iwconfig ath2 key off]
     ... finished.
    FCMD[brctl addif br0 ath0]
    FCMD[brctl addif br0 ath1]
    FCMD[brctl addif br0 ath2]
    FCMD[brctl setfd br0 0.1]
    FCMD[ifconfig ath0 0.0.0.0 up]
    FCMD[ifconfig ath1 0.0.0.0 up]
    FCMD[ifconfig ath2 0.0.0.0 up]
    FCMD[ifconfig ath0 up]
    FCMD[iwconfig ath0 txpower 21]
    Set Atheros power to 21 (dBm)
    FCMD[route add -net 239.0.0.0 netmask 255.0.0.0 br0]
    Encryption using WPAWPA2_PSK ...
    Encryption using TKIP CCMP ...
    FCMD[route add -net 239.0.0.0 netmask 255.0.0.0 br0]
    Encryption using WPAWPA2_PSK ...
    Encryption using TKIP CCadf: module license 'Proprietary' taints kernel.
    MP ...
    FCMD[rouDisabling lock debugging due to kernel taint
    te add -net 239.0.0.0 netmask 255.0.0.0 br0]
    Encryption using WPAWPA2_PSK ...
    Encryption using TKIP CCMP ...
    Starting Hostapd ...            FCMD[killall hostapd1]
    FCMD[/sbin/hostapd1 -P /var/hostapd.pid /etc/hostapd0.conf /etc/hostapd1.conf &]
    OK
    FCMD[iwconfig ath0 rate auto]
    FCMD[iwconfig ath1 rate auto]
    FCMD[iwconfig ath2 rate auto]
    cmd [sh /var/sysconfd/athwlan0.sh]
    ath_hal: 0.9.17.1 (AR5416, AR9380, WRITE_EEPROM, 11D)
    ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
    ath_dfs: Version 2.0.0
    Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
    ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
    ath_ahb: 10.1.467 (Atheros/multi-bss)
    __ath_attach: Set global_scn[0]
    Enterprise mode: 0x60000000
    Restoring Cal data from Flash
    Green-AP : Green-AP : Attached
    
    ath_get_caps[5976] rx chainmask mismatch actual 3 sc_chainmak 0
    ath_get_caps[5951] tx chainmask mismatch actual 3 sc_chainmak 0
    _ieee80211_resmgr_create: Multi-Channel Scheduler unavailable since no TSF Timer.
    Error: _ieee80211_resmgr_create: no Multi-chan hw caps. Disabling Off Channel scheduler.
    ath_attach_dfs[11955] dfsdomain 1
    SC Callback Registration for wifi0
    wifi0: Atheros ???: mem=0xb8100000, irq=2
    ath_pci: 10.1.467 (Atheros/multi-bss)
    ath_pci_probe
    PCI device id is 003c :003c
    ath_pci 0000:01:00.0: ath DEBUG: sc=0x87d5a400
    
     ol_ath_pci_configure : num_desired MSI set to 0
    
     Using PCI Legacy Interrupt
    __ol_ath_attach: ath_attach TODO
    ol_ath_attach() BMI inited.
    ol_ath_attach() BMI Get Target Info.
    ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c
    NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
    ol_ath_attach() configure Target .
    qc98xx_verify_checksum: flash checksum passed: 0x667f
    ol_transfer_bin_file 1690: Download Flash data len 2116
    ol_transfer_bin_file 1637: Download Firmware data len 190144
    ol_ath_attach() Download FW. 
    ol_ath_attach() HT Create .
    ol_ath_attach() HIF Claim.
    ol_ath_attach() BMI Done. 
    ol_ath_attach() WMI attached. wmi_handle 87db0000 
    +HWT
    CE_recv_buf_enqueue 457 Populate last entry 512 for CE 5
    CE_recv_buf_enqueue 466 CE 5 wi 511 dest_ptr 0xe51be0 nbytes 0 recv_ctxt 0x807251a0
    -HWT
    HTC Service:0x0300 ep:1 TX flow control disabled
    CE_pkt_dl_len_set CE 4 Pkt download length 42
    TXRX: Created pdev 80726e00
    wmi_service_ready_event_rx:  WMI UNIFIED SERVICE READY event 
    num_rf_chain : 00000003
    ht_cap_info: : 0000085b
    vht_cap_info : 338001b2
    vht_supp_mcs : 0000ffea
    LARGE_AP enabled. num_peers 144, num_vdevs 16, num_tids 256
    idx 0 req 1  num_units 0 num_unit_info 2 unit size 404 actual units 145 
    chunk 0 len 58580 requested ,ptr  0x790000 
    FIRMWARE:P 145 V 16 T 443
     
    wmi_ready_event_rx:  WMI UNIFIED READY event 
    ol_ath_connect_htc() WMI is ready
    ol_ath_set_host_app_area TODO
    target uses HTT version 2.1; host uses 2.1
    ol_ath_attach() connect HTC. 
    ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
    ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
    ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
    ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
    ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
    ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
    ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
    ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
    ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
    Skipping VHT80 channel 5825
    ol_ath_phyerr_attach: called
    OL Resmgr Init-ed
    Green-AP : Green-AP : Attached
    
    Green-AP : Attached
    ol_if_dfs_setup: called 
    ol_if_dfs_attach: called; ptr=8077d974, radar_info=8061fbe8
    ol_ath_rtt_meas_report_attach: called
    ol_ath_attach() UMAC attach . 
    ol_if_dfs_configure: called
    ol_if_dfs_configure: FCC domain
    ol_if_dfs_disable: called
    ol_ath_attach: Calling ol_if_dfs_configure
    __ol_ath_attach: init tx/rx TODO
    __ol_ath_attach: hard_header_len reservation 58
    __ol_ath_attach: dev name wifi1
    SC Callback Registration for wifi1
    
    VAP device ath0 created 
    ath0
    VAP device ath1 created 
    ath1
    VAP device ath2 created 
    ath2
    
    
    
    
    
    
    
    
    
    
    
    
    
    
     
     DES SSID SET=Guest04400 
     
     DES SSID SET=Copy04400 
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    killall: hostapd1: no process killed
    device ath0 entered promiscuous mode
    device ath1 entered promiscuous mode
    device ath2 entered promiscuous mode
    br0: port 2(ath0) entering learning state
    br0: port 2(ath0) entering forwarding state
    br0: port 3(ath1) entering learning state
    br0: port 3(ath1) entering forwarding state
    br0: port 4(ath2) entering learning state
    route: SIOCADDRT: File exists
    route: SIOCADDRT: File exists
    route: SIOCADDRT: File exists
    killall: hostapd1: no process killed
    Configuration fi ieee80211_ioctl_siwmode: imr.ifm_active=1442432, new mode=3, valid=1 
    le: /etc/hostapd0.conf
    br0: port 4(ath2) entering forwarding state
    br0: port 2(ath0) entering disabled state
    Flushing old sta DEVICE IS DOWN ifname=ath0
    tion entries
     DEVICE IS DOWN ifname=ath0
    Could not connect to kernel driver.
    Using interface ath0 with hwaddr 34:76:c5:35:11:30 and ssid 'AirPort04400'
    cmd [rm -f /tmp/wifi0_ifconfig]
    cmd [ifconfig | grep wifi0 >/tmp/wifi0_ifconfig]
    cmd [rm -f /tmp/ath0_ifconfig]
    cmd [ifconfig ath0 | grep ath0 >/tmp/ath0_ifconfig]
    cmd [rm -f /tmp/ath1_ifconfig]
    cmd [ifconfig ath1 | grep ath1 >/tmp/ath1_ifconfig]
    cmd [rm -f /tmp/ath2_ifconfig]
    cmd [ifconfig ath2 | grep ath2 >/tmp/ath2_ifconfig]
    Sam: hostapd_init_wps
    WPS: Converting display to virtual_display for WPS 2.0 compliance
    WPS: Converting push_button to virtual_push_button for WPS 2.0 compliance
    cmd [ifconfig ath0 down]
    br0: port 2(ath0) entering learning state
    br0: port 2(ath0) entering forwarding state
    br0: port 2(ath0) entering disabled state
    Configuration fi ieee80211_ioctl_siwmode: imr.ifm_active=1442432, new mode=3, valid=1 
    le: /etc/hostapd1.conf
    cmd [ifconfig ath1 down]
    br0: port 3(ath1) entering disabled state
    Flushing old sta DEVICE IS DOWN ifname=ath1
    tion entries
     DEVICE IS DOWN ifname=ath1
    Could not connect to kernel driver.
    cmd [ifconfig ath2 down]
    br0: port 4(ath2) entering disabled state
    Using interface ath1 with hwaddr 06:76:c5:35:11:30 and ssid 'Guest04400'
    cmd [ifconfig ath0 up]
    Sam: hostapd_init_wps
    br0: port 2(ath0) entering learning state
    cmd [ifconfig ath1 up]
    br0: port 2(ath0) entering forwarding state
    br0: port 3(ath1) entering learning state
    cmd [sleep 1]
    br0: port 3(ath1) entering forwarding state
    cmd [echo 0 22 3 > /proc/simple_config/simple_config_led]
    System Debug : gWlan24GOff[-1].
    System Debug : gWlan5GOff[-1].
    cmd [echo 0 22 3 > /proc/simple_config/simple_config_led]
    cmd [echo 0 21 2 > /proc/simple_config/simple_config_led]
    athOpen OK
    cmd [mknod /dev/watchdog c 10 130]
    cmd [watchdog -t 15 /dev/watchdog]
    cmd [wlanconfig ath0 list chan > /tmp/wls_24g_chanlist]
    OK
    
    
    #############################################
    Initialize Radio setting ... OK
    Configuring radio2 setting ... 
    Configuring Atheros device index:1... wifiname=wifi1 , macaddr=34:76:C5:35:11:31FCMD[ifconfig wifi1 hw ether 34:76:C5:35:11:31]
    FCMD[iwpriv wifi1 setCountryID 4015]
    FCMD[wlanconfig ath3 create wlandev wifi1 wlanmode ap ]
    FCMD[iwpriv ath3 nss 3]
    FCMD[iwpriv wifi1 rxchainmask 7]
    FCMD[iwpriv wifi1 txchainmask 7]
    FCMD[iwpriv wifi1 burst 1]
    FCMD[ifconfig eth0 txqueuelen 10000]
    FCMD[iwpriv ath3 mode 11acvht80]
    FCMD[iwpriv ath3 wds 0]
    FCMD[iwpriv ath3 shortgi 1]
    FCMD[iwpriv ath3 ldpc 1]
    FCMD[iwpriv ath3 ampdu 64]
    FCMD[iwpriv ath3 amsdu 3]
    FCMD[iwpriv ath3 chwidth 2]
    FCMD[iwpriv ath3 disablecoext 1]
    FCMD[sleep 1]
    -----> LOG : WLAN2, Wireless mode = 802.11 5G ac
    FCMD[iwpriv ath3 ap_bridge 1]
    FCMD[iwpriv ath3 bssid_bridge 1]
    FCMD[iwconfig ath3 essid "Stream04400"]
    -----> LOG : WLAN2, SSID1 = Stream04400
    FCMD[iwconfig ath3 channel 36]
    -----> LOG : WLAN2, Channel = 36
    FCMD[iwpriv ath3 bintval 100]
    -----> LOG : WLAN2, Beacon Interval = 100(ms)
    FCMD[iwpriv ath3 dtim_period 1]
    -----> LOGisCountryCodeValid: EEPROM regdomain 0x0
     : WLAN2, DTIM pol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
    eriod = 1
    FCMD[ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
    iwpriv ath3 shprol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
    eamble 0]
    -----ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
    > LOG : WLAN2, Pol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
    reamble = Long Pol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
    reamble
    FCMD[iwol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
    config ath3 rts ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
    2347]
    FCMD[iwprSkipping VHT80 channel 5660
    iv ath3 countryiSkipping VHT80 channel 5680
    e 1]
    FCMD[iwpriSkipping VHT80 channel 5700
    v ath3 hide_ssid 0]
    FCMD[iwpriv ath3 wmm 1]
    FCath_ioctl: SIOC80211IFCREATE CALLED
    MD[iwpriv ath3 mwmi_unified_vdev_create_send: ID = 0 VAP Addr = 34:76:c5:35:11:31:
    castenhance 2]
    TXRX: Created vdev 80772560 (34:76:c5:35:11:31)
    FCMD[iwpriv ath3Setting vdev param = 26, value = 147
     mcast_rate 3000Setting vdev param = 27, value = 295
    00]
    FCMD[iwprivSetting vdev param = 28, value = 300
     wifi1 set_swaplVAP device ath3 created 
    ed 1]
    FCMD[killTXRX: ol_txrx_peer_find_add_id: peer 80617000 ID 64
    all hostapd2]
    ETXRX: ol_txrx_peer_find_add_id: peer 80617000 ID 80
    ncryption using WEP ...      
    FCMD[iwconfig ath3 key off]
     ... finished.
    FCMD[brctl addif br0Setting vdev param = 20, value = 3
     ath3]
    FCMD[brctl setfd br0 0.1]
    FCMD[ifconfig ath3 0.0.0.0 up]
    FCMD[ifconfig ath3 up]
    FCMD[iwconfig ath3 txpower 21]
    Set Atheros power to 21 (dBm)
    FCMD[route add -net 239.0.0.0 netmask 255.0.0.0 br0]
    Encryption using WPA2-PSK ...
    ESetting vdev param = f, value = 0
    ncryption using AES ...
    Starting Hostapd ...   Setting vdev param = 1a, value = 1
             FCMD[killall hostapd2]
    FCMD[/sbin/hostSetting vdev param = 1b, value = 1
    apd2 -P /var/hostapd2.pid /etc/hostapd20.conf &]
    OK
    FCMD[#iwpriv ath3 vhtmcs 0]
    cmd [sh /var/sysconfd/athwlan1.sh]
    
    ath3
    
    
    
    
    
    
    
    
    
    
    
    
    
    OL vap_stop +
    wmi_unified_vdev_stop_send 
    OL vap_stop -
    STOPPED EVENT for vap 0 
    
    
    
    
    
    
    
    
    Invalid command : set_swapled
    killall: hostapd2: no process killed
    ol_ath_vap_set_param: VAP param unsupported param:75 value:1
    device ath3 entered promiscuous mode
    OL vap_stop +
    wmi_unified_vdev_stop_send 
    OL vap_stop -
    STOPPED EVENT for vap 0 
    OL vap_start +
    OL vap_start -
    ol_vdev_start_resp_ev
    ol_ath_vap_join: join operation is only for STA/IBSS mode
    ol_ath_wmm_update:
    Setting vdev param = 3, value = 100
    Notification to UMAC VAP layer
    br0: port 5(ath3) entering learning state
    route: SIOCADDRT: File exists
    killall: hostapd2: no process killed
    Configuration fi ieee80211_ioctl_siwmode: imr.ifm_active=131738, new mode=3, valid=1 
    le: /etc/hostapdwmi_unified_vdev_stop_send 
    20.conf
    STOPPED EVENT for vap 0 
    cmd [rm -f /tmp/wifi1_ifconfig]
    cmd [ifconfig | grep wifi1 >/tmp/wifi1_ifconfig]
    br0: port 5(ath3) entering forwarding state
    br0: port 5(ath3) entering disabled state
    ol_ath_vap_set_param: VAP param unsupported param:33 value:0
    Flushing old sta DEVICE IS DOWN ifname=ath3
    tion entries
     DEVICE IS DOWN ifname=ath3
    Could not connecol_ath_vap_set_param: VAP param unsupported param:33 value:0
    t to kernel driver.
    Using interface ath3 with hwaddr 34:76:c5:35:11:31 and ssid 'Stream04400'
    cmd [rm -f /tmp/ath3_ifconfig]
    cmd [ifconfig ath3 | grep ath3 >/tmp/ath3_ifconfig]
    cmd [sleep 1]
    Sam: hostapd_iniol_ath_vap_set_param: VAP param unsupported param:18 value:1
    t_wps
    WPS: Convol_ath_vap_set_param: VAP param unsupported param:75 value:1
    erting display t Group Keyidx set=1 
     o virtual_displawmi_unified_vdev_install_key_send Setting Key for Macaddress:0x311135c57634 
    y for WPS 2.0 coKeyix=1 Keylen=16 Keyflags=1 Cipher=4 
     Keydata=mpliance
    WPS: C0x98 onverting push_b0xfd utton to virtual0x41 _push_button for0x83  WPS 2.0 complia0x4e nce
    0xd0 0xd0 0x1a 0xcb 0x1 0xdf 0x4d 0xc2 0x86 0x50 0x34 
    ol_ath_vap_set_param: VAP param unsupported param:75 value:0
    TXRX: ol_txrx_peer_find_add_id: peer 80617000 ID 176
    TXRX: sec spec for peer 80617000 (34:76:c5:35:11:31): mcast key of type 6
    Setting vdev param = 1f, value = 1
    ol_ath_vap_set_param: VAP param unsupported param:33 value:1
    OL vap_stop +
    wmi_unified_vdev_stop_send 
    OL vap_stop -
    STOPPED EVENT for vap 0 
    OL vap_start +
    OL vap_start -
    ol_vdev_start_resp_ev
    ol_ath_vap_join: join operation is only for STA/IBSS mode
    ol_ath_wmm_update:
    Setting vdev param = 3, value = 100
    Notification to UMAC VAP layer
    br0: port 5(ath3) entering learning state
    br0: port 5(ath3) entering forwarding state
    cmd [echo 0 21 3 > /proc/simple_config/simple_config_led]
    System Debug : gWlan24GOff[-1].
    System Debug : gWlan5GOff[-1].
    cmd [echo 0 22 3 > /proc/simple_config/simple_config_led]
    cmd [echo 0 21 3 > /proc/simple_config/simple_config_led]
    athOpen OK
    cmd [mknod /dev/watchdog c 10 130]
    mknod: /dev/watchdog: File exists
    cmd [watchdog -t 15 /dev/watchdog]
    cmd [wlanconfig ath3 list chan > /tmp/wls_5g_chanlist]
    OK
    cmd [ln -s /apps/usr/sbin/pppd /usr/sbin/pppd0]
    cmd [ln -s /apps/usr/sbin/pppd /usr/sbin/pppd1]
    Wan Manager...
    Configuring WAN device[WAN0] ...
    cmd [echo 1 > /proc/wancon_type ]
    Connect to ISP using PPPoE ... -----> LOG : WAN, start PPPoE mode
    cmd [chmod 755 /etc/ppp/pap-secrets]
    cmd [chmod 755 /etc/ppp/chap-secrets]
    cmd [chmod 755 /etc/ppp/options.tty0]
    cmd [chmod 0755 /etc/wanconn0.conf]
    cmd [ifconfig eth0.2 hw ether 34:76:C5:35:11:32 0.0.0.0   up]
    -----> LOG : WAN, No PHY Link
    No PHY Link
    cmd [/sbin/wanmanager &]
    -----> LOG : DNS, start DNS Proxy
    Set Domain Routing for FLET'S Square Connection...            
    failed to read /etc/wanconn1.conf
    Failed to load /etc/wanconn1.conf
    Starting DNS Proxy ...            cmd [/sbin/dnsmasq -C /etc/dnsmasq.conf -i br0 -k &]
    FAILED
    -----> LOG : DHCP, start DHCP Server
    Starting DHCP(udhcpd) server ...            cmd [udhcpd &]
    udhcpd (v1.7.5) started
    Unable to open /etc/udhcpd.leases for reading
    OK
    Starting FW manager ...           cmd [/sbin/fwmanager&]
    OK
    cmd [echo JST-9 > /etc/TZ]
    Starting ntpclient ...            
    -----> LOG : NTP, start NTP Client
    Setup tc for QoS ... Disabled
    
    SCHEDULE, ServiceWlanLowRateInit ...service_index[0].
    -----> LOG : SCHEDULE, Wireless Normal Mode
    
    SCHEDULE, ServiceWlsRadioOffInit ...service_index[1].
    cmd [ifconfig ath0 up]
    cmd [ifconfig ath1 up]
    cmd [echo 0 22 3 > /proc/simple_config/simple_config_led]
    fwmMsgqId is 0
    === Firmware Manager start === 
    -----> LOG : SCHEDULE, 2.4G Wireless Radio On
    
    SCHEDULE, Service5GWlanLowRateInit ...service_index[2].
    ----Port led blink on
    -> LOG : SCHEDULE, 5G Wireless Normal Mode
    
    SCHEDULE, Service5GWlsRadioOffInit ...service_index[3].
    cmd [ifconfig ath3 up]
    cmd [echo 0 21 3 > /proc/simple_config/simple_config_led]
    -----> LOG : SCHEDULE, 5G Wireless Radio On
    
    SCHEDULE, ServiceLedOffInit ...service_index[4].
    -----> LOG : SCHEDULE, LED On
    cmd [ethreg -l 1]
    cmd [echo 31 22 >/proc/simple_config/simple_config_led]
    cmd [echo 31 21 >/proc/simple_config/simple_config_led]
    cmd [echo 0 14 3 > /proc/simple_config/simple_config_led]
    
    SCHEDULE, ServiceLanOffInit ...service_index[5].
    -----> LOG : SCHEDULE, Set LAN Interface Up
    cmd [ethreg -i eth0 -p 3 0x00=0x1000]
    ethreg: eth0: Success
    cmd [ethreg -i eth0 -p 2 0x00=0x1000]
    ethreg: eth0: Success
    cmd [ethreg -i eth0 -p 1 0x00=0x1000]
    ethreg: eth0: Success
    cmd [ethreg -i eth0 -p 0 0x00=0x1000]
    ethreg: eth0: Success
    
    SCHEDULE, ServiceWanOffInit ...service_index[6].
    -----> LOG : SCHEDULE, Set WAN InterfForce Low Rate Off
    ace Up
    cmd [ethreg -i eth0 -p 4 0x00=0x1000]
    ethreg: eth0: Success
    
    SCHEDULE, ServiceLanLowRateInit ...service_index[7].
    -----> LOG : SCHEDULE, Set LAN Link Rate to 1000Mbps
    cmd [ethreg -v 0]
    
    SCHEDULE, ServicePowerLedInit ...service_index[8].
    cmd [echo 0 3 2 > /proc/simple_config/simple_config_led]
    
    
    Schedule starting  [scheduleOpen], ...wait result..
    Schedule result :[Disable (No rules)]. 
    -----> LOG : NET, start NAT
    -----> LOG : NET, start Firewall
    Configuring network routing and filtering ...FCMD[modprobe ipt_MASQUERADE]
    FCMD[modprobe ipt_REDIRECT]
    FCMD[modprobe ipt_LOG]
    FCMD[modprobe ipt_REJECT]
    FCMD[modprobe iptable_mangle]
    FCMD[modprobe iptable_nat]
    FCMD[modprobe ipt_connlimit]
    FCMD[modprobe ipt_ttl]
    FCMD[modprobe ipt_TTL]
    FCMD[modprobe ipt_time]
    FCMD[modprobe ipt_tos]
    FCMD[modprobe ipt_TOS]
    FCMD[modprobe ipt_TRIGGER]
    FCMD[modprobe xt_MARK]
    FCMD[modprobe xt_TCPMSS]
    FCMD[modprobe xt_CONNMARK]
    FCMD[modprobe xt_pkttype]
    FCMD[modprobe xt_multiport]
    FCMD[modprobe xt_connmark]
    FCMD[modprobe xt_tcpmss]
    FCMD[modprobe xt_conntrack]
    FCMD[modprobe xt_string]
    FCMD[modprobe xt_state]
    FCMD[modprobe xt_length]
    FCMD[modprobe xt_limit]
    FCMD[modprobe xt_mac]
    FCMD[modprobe xt_mark]
    FCMD[modprobe ipt_IMQ]
    FCMD[modprobe xt_iprange]
    cmd [sh /var/sysconfd/modprobe_iptable.sh]
    modprobe: module ipt_MASQUERADE not found
    modprobe: failed to load module ipt_MASQUERADE
    modprobe: module ipt_REDIRECT not found
    modprobe: failed to load module ipt_REDIRECT
    modprobe: module ipt_LOG not found
    modprobe: failed to load module ipt_LOG
    modprobe: module ipt_REJECT not found
    modprobe: failed to load module ipt_REJECT
    modprobe: module iptable_mangle not found
    modprobe: failed to load module iptable_mangle
    modprobe: module iptable_nat not found
    modprobe: failed to load module iptable_nat
    modprobe: module ipt_connlimit not found
    modprobe: failed to load module ipt_connlimit
    modprobe: module ipt_ttl not found
    modprobe: failed to load module ipt_ttl
    modprobe: module ipt_TTL not found
    modprobe: failed to load module ipt_TTL
    modprobe: module ipt_time not found
    modprobe: failed to load module ipt_time
    modprobe: module ipt_tos not found
    modprobe: failed to load module ipt_tos
    modprobe: module ipt_TOS not found
    modprobe: failed to load module ipt_TOS
    modprobe: module ipt_TRIGGER not found
    modprobe: failed to load module ipt_TRIGGER
    modprobe: module xt_MARK not found
    modprobe: failed to load module xt_MARK
    modprobe: module xt_TCPMSS not found
    modprobe: failed to load module xt_TCPMSS
    modprobe: module xt_CONNMARK not found
    modprobe: failed to load module xt_CONNMARK
    modprobe: module xt_pkttype not found
    modprobe: failed to load module xt_pkttype
    modprobe: module xt_multiport not found
    modprobe: failed to load module xt_multiport
    modprobe: module xt_connmark not found
    modprobe: failed to load module xt_connmark
    modprobe: module xt_tcpmss not found
    modprobe: failed to load module xt_tcpmss
    modprobe: module xt_conntrack not found
    modprobe: failed to load module xt_conntrack
    modprobe: module xt_string not found
    modprobe: failed to load module xt_string
    modprobe: module xt_state not found
    modprobe: failed to load module xt_state
    modprobe: module xt_length not found
    modprobe: failed to load module xt_length
    modprobe: module xt_limit not found
    modprobe: failed to load module xt_limit
    modprobe: module xt_mac not found
    modprobe: failed to load module xt_mac
    modprobe: module xt_mark not found
    modprobe: failed to load module xt_mark
    modprobe: module ipt_IMQ not found
    modprobe: failed to load module ipt_IMQ
    modprobe: module xt_iprange not found
    modprobe: failed to load module xt_iprange
    FCMD[iptables --flush]
    FCMD[iptables -t nat --flush]
    FCMD[iptables -t mangle --flush]
    FCMD[iptables -A INPUT -i lo -j ACCEPT]
    FCMD[iptables -A OUTPUT -o lo -j ACCEPT]
    FCMD[iptables --policy INPUT DROP]
    FCMD[iptables --policy OUTPUT DROP]
    FCMD[iptables --policy FORWARD DROP]
    FCMD[iptables -t nat --policy PREROUTING ACCEPT]
    FCMD[iptables -t nat --policy OUTPUT ACCEPT]
    FCMD[iptables -t nat --policy POSTROUTING ACCEPT]
    FCMD[iptables -t mangle --policy PREROUTING ACCEPT]
    FCMD[iptables -t mangle --policy POSTROUTING ACCEPT]
    FCMD[iptables -t mangle --policy OUTPUT ACCEPT]
    FCMD[iptables --delete-chain]
    FCMD[iptables -t nat --delete-chain]
    FCMD[iptables -t mangle --delete-chain]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags ALL NONE -j DROP]
    FCMD[iptables -A FORWARD -p tcp --tcp-flags ALL NONE -j DROP]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags ALL ALL -j DROP]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags ALL SYN,RST,ACK,FIN,URG -j DROP]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags SYN,FIN SYN,FIN -j DROP]
    FCMD[iptables -A FORWARD -p tcp --tcp-flags SYN,FIN SYN,FIN -j DROP]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags SYN,RST SYN,RST -j DROP]
    FCMD[iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN,RST -j DROP]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags FIN,RST FIN,RST -j DROP]
    FCMD[iptables -A FORWARD -p tcp --tcp-flags FIN,RST FIN,RST -j DROP]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags ACK,FIN FIN -j DROP]
    FCMD[iptables -A FORWARD -p tcp --tcp-flags ACK,FIN FIN -j DROP]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags ACK,PSH PSH -j DROP]
    FCMD[iptables -A FORWARD -p tcp --tcp-flags ACK,PSH PSH -j DROP]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags ACK,URG URG -j DROP]
    FCMD[iptables -A FORWARD -p tcp --tcp-flags ACK,URG URG -j DROP]
    FCMD[iptables -X synflood]
    FCMD[iptables -N synflood]
    FCMD[iptables -A synflood -p tcp --syn -m limit --limit 20/s --limit-burst 20 -j RETURN]
    FCMD[iptables -A synflood -p tcp -j REJECT --reject-with tcp-reset]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp -m state --state NEW -j synflood]
    FCMD[iptables -t filter -X urlfilter]
    FCMD[iptables -t filter -N urlfilter]
    FCMD[iptables -t nat -A PREROUTING -i br0 -p tcp -d 192.168.0.1 --dport 8080 -j DROP]
    FCMD[iptables -t nat -A PREROUTING -i br0 -p tcp --sport 1024:65535 -d 192.168.0.1 --dport 80 -j DNAT --to-destination 192.168.0.1:8080]
    FCMD[iptables -t nat -A PREROUTING -i br0 -p tcp --sport 1024:65535 ! -d 192.168.0.1 --dport 80 -j DNAT --to-destination 192.168.0.1:10404]
    FCMD[iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT]
    FCMD[iptables -A OUTPUT -m state --state ESTABLISHED,RELATED -j ACCEPT]
    FCMD[iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT]
    FCMD[iptables -A INPUT -s 192.168.0.1 -j DROP]
    FCMD[iptables -A FORWARD -s 192.168.0.1 -j DROP]
    FCMD[iptables -A OUTPUT -o br0 ! -s 192.168.0.1 -j DROP]
    FCMD[iptables -A INPUT -i br0 -p udp --dport 1900 -j ACCEPT]
    FCMD[iptables -A INPUT -i br0 -p tcp --dport 2869 -j ACCEPT]
    FCMD[iptables -A INPUT -i br0 -d 0.0.0.0 -j DROP]
    FCMD[iptables -A INPUT   ! -p udp -d 224.0.0.0/4 -j DROP]
    FCMD[iptables -A FORWARD ! -p udp -d 224.0.0.0/4 -j DROP]
    FCMD[iptables -A INPUT -i br0 -s 239.0.0.0/8 -j ACCEPT]
    FCMD[iptables -A INPUT -i br0 -d 239.0.0.0/8 -j ACCEPT]
    FCMD[iptables -A OUTPUT -o br0 -p udp -s 0.0.0.0 --sport 67 -d 255.255.255.255 --dport 68 -j ACCEPT]
    FCMD[iptables -A INPUT -i br0 -p tcp --dport 53 -j ACCEPT]
    FCMD[iptables -A INPUT -i br0 -p udp --dport 53 -j ACCEPT]
    FCMD[iptables -A OUTPUT -o eth0.2 -p udp --dport 53 -j ACCEPT]
    FCMD[iptables -A OUTPUT -o eth0.2 -p tcp --dport 53 -j ACCEPT]
    FCMD[iptables -A INPUT -i br0 -p udp --dport 69 -j ACCEPT]
    FCMD[iptables -A INPUT -i br0 -p udp -s 192.168.0.0/255.255.255.0 --dport 123 -j ACCEPT]
    FCMD[iptables -A INPUT --fragment -p icmp -j DROP]
    FCMD[iptables -A OUTPUT --fragment -p icmp -j DROP]
    FCMD[iptables -A FORWARD --fragment -p icmp -j DROP]
    FCMD[iptables -A OUTPUT -p icmp --icmp-type source-quench -j ACCEPT]
    FCMD[iptables -A FORWARD -p icmp --icmp-type source-quench -j ACCEPT]
    FCMD[iptables -A INPUT -p icmp --icmp-type parameter-problem -j ACCEPT]
    FCMD[iptables -A OUTPUT -p icmp --icmp-type parameter-problem -j ACCEPT]
    FCMD[iptables -A FORWARD -p icmp --icmp-type parameter-problem -j ACCEPT]
    FCMD[iptables -A INPUT -p icmp --icmp-type destination-unreachable -j ACCEPT]
    FCMD[iptables -A OUTPUT -o br0 -p icmp --icmp-type destination-unreachable -d 192.168.0.1 -j ACCEPT]
    FCMD[iptables -A FORWARD -o br0 -p icmp --icmp-type destination-unreachable -d 192.168.0.1 -j ACCEPT]
    FCMD[iptables -A OUTPUT -p icmp --icmp-type fragmentation-needed -j ACCEPT]
    FCMD[iptables -A FORWARD -p icmp --icmp-type fragmentation-needed -j ACCEPT]
    FCMD[iptables -A OUTPUT -p icmp --icmp-type destination-unreachable -j DROP]
    FCMD[iptables -A INPUT -p icmp --icmp-type time-exceeded -j ACCEPT]
    FCMD[iptables -A FORWARD -o br0 -p icmp --icmp-type time-exceeded -d 192.168.0.1 -j ACCEPT]
    FCMD[iptables -A OUTPUT -p icmp --icmp-type echo-request -m state --state NEW -j ACCEPT]
    FCMD[iptables -X bad-ping]
    FCMD[iptables -N bad-ping]
    FCMD[iptables -A bad-ping -p icmp --icmp-type echo-request -m limit --limit 20/s --limit-burst 20 -j ACCEPT]
    FCMD[iptables -A bad-ping -p icmp --icmp-type echo-request -j DROP]
    FCMD[iptables -A INPUT -i br0 -p icmp --icmp-type echo-request -j bad-ping]
    FCMD[iptables -A OUTPUT -o br0 -s 192.168.0.1 -j ACCEPT]
    FCMD[iptables -A FORWARD -i br0 -o br0 -j ACCEPT]
    FCMD[iptables -A INPUT -i br0 -j ACCEPT]
    FCMD[/sbin/ifconfig eth0.1 up]
    Iptable restart VPN ACL ...VPN ACL ...
    FCMD[echo 1 > /proc/sys/net/ipv4/ip_forward]
    FCMD[echo 0 > /proc/sys/net/ipv4/conf/all/rp_filter]
    FCMD[echo 15 > /proc/sys/net/ipv4/route/gc_interval]
    FCMD[echo 1 > /proc/sys/net/ipv4/ip_dynaddr]
    FCMD[echo 1 > /proc/sys/net/ipv4/conf/eth0.2/arp_filter]
    cmd [sh /var/sysconfd/iptables.sh]
    iptables: No chain/target/match by that name.
    iptables: No chain/target/match by that name.
    iptables: No chain/target/match by that name.
    OK
    cmd [cp /apps/etc/ethertypes /etc/ethertypes]
    Configuring Bridge filtering ...FCMD[ebtables -A FORWARD --in-interface ath1 --out-interface ath0 -j DROP]
    FCMD[ebtables -A FORWARD --in-interface ath0 --out-interface ath1 -j DROP]
    FCMD[ebtables -A FORWARD --in-interface ath1 --out-interface ath3 -j DROP]
    FCMD[ebtables -A FORWARD --in-interface ath3 --out-interface ath1 -j DROP]
    FCMD[ebtables -A FORWARD --in-interface ath1 --out-interface ath2 -j DROP]
    FCMD[ebtables -A FORWARD --in-interface ath2 --out-interface ath1 -j DROP]
    FCMD[ebtables -A FORWARD --in-interface ath1 --out-interface eth0.1 -j DROP]
    FCMD[ebtables -A FORWARD --in-interface eth0.1 --out-interface ath1 -j DROP]
    cmd [sh /var/sysconfd/ebtables.sh]
    Ebtables v2.0 registered
    OK
    cmd [echo 0 23 1 > /proc/simple_config/simple_config_led]
    Starting SiteBlock server ...            
    Netpacket Filter Open ....              sysGetKernelInfo: netv :1.0
    Kernel netpkt ver netv: 1.0
    cmd [insmod /lib/netpktfilter.ko]
    bsfdrv_major = 235
    cmd [echo lan-add eth0.1 > /proc/netpktconfig/config_interface]
    cmd [echo lan-add ath2 > /proc/netpktconfig/config_interface]
    cmd [echo lan-add ath1 > /proc/netpktconfig/config_interface]
    cmd [echo lan-add ath0 > /proc/netpktconfig/config_interface]
    cmd [echo lan-add ath3 > /proc/netpktconfig/config_interface]
    cmd [echo BSF 0 > /proc/netpktconfig/config_interface]
    cmd [echo wlan-add ath2 > /proc/netpktconfig/config_interface]
    cmd [echo wlan-add ath1 > /proc/netpktconfig/config_interface]
    cmd [echo wlan-add ath0 > /proc/netpktconfig/config_interface]
    cmd [echo wlan-add ath3 > /proc/netpktconfig/config_interface]
    cmd [echo wan-add eth0.2 > /proc/netpktconfig/config_interface]
    cmd [echo pppoe 0 > /proc/netpktconfig/config_interface]
    cmd [echo ipv6 1 > /proc/netpktconfig/config_interface]
    cmd [echo lan-ip c0a80001 > /proc/netpktconfig/config_interface]
    cmd [echo igmp_snooping 1 > /proc/netpktconfig/config_interface]
    OK
    Starting UPNPD  ...  -----> LOG : UPnP, Start
    cmd [uuidgen -m 3476C5351130]
    WAN Speed = 10 Mbps
    cmd [route add -net 239.0.0.0 netmask 255.0.0.0 br0]
    route: SIOCADDRT: File exists
    cmd [mkdir -p /etc/linuxigd]
    cmd [ln -sf /apps/etc/linuxigd/* /etc/linuxigd/.]
    cmd [upnpd -f  ppp0 br0&]
    FAILED
    IGMP Proxy is disabled...  -----> LOG : HTTP, start
    cmd [httpd&]
    Starting DDNS  ...  Disabled
    Staring ALG...           OK
    Starting LLTD ...           -----> LOG : WLAN, start LLTD
    cmd [lld2d -d -t 31 br0 &]
    OK
    -----> LOG : WAN, stop Hardware NAT
    cmd [echo 0 > /proc/qca_switch/nf_athrs17_hnat]
    cmd [ethreg 0x30=0x80000300]
    ethreg: eth0: Success
    cmd [echo WN-AC1600DGR > /etc/hostname]
    cmd [echo "iface br0 static" > /etc/network/interfaces]
    cmd [echo -540 > /etc/gmoffset]
    cmd [HDLFind -c /etc/HDLFind.conf]
    cmd [route add -net 224.0.0.0 netmask 224.0.0.0 br0]
    cmd [HDLQC -c /etc/HDLQC.conf]
    cmd [mkdir -p /etc/sxpsplus]
    cmd [cp -f /apps/etc/sxpsplus/* /etc/sxpsplus/]
    cmd [cp -f /lib/modules/2.6.31/kernel/drivers/usb/class/usblp.ko /lib/]
    cmd [insmod /lib/usblp.ko]
    usbcore: registered new interface driver usblp
    cmd [/etc/sxpsplus/rc.sxpsplus.sh start]
    Initialize SX PrintServer Plus
    Starting SX PrintServer Plus Daemon: /sbin/sxpspd -i br0 -D
    cmd [mkdir -p /lib/modules/sxuptp/daemon]
    cmd [ln -sf /apps/lib/modules/sxuptp/daemon/* /lib/modules/sxuptp/daemon]
    cmd [mkdir -p /lib/modules/sxuptp/drivers]
    cmd [ln -sf /apps/lib/modules/sxuptp/drivers/* /lib/modules/sxuptp/drivers]
    cmd [mkdir -p /lib/modules/sxuptp/wq]
    cmd [ln -sf /apps/lib/modules/sxuptp/wq/* /lib/modules/sxuptp/wq]
    cmd [mkdir -p /etc/sxuptp]
    cmd [cp -f /apps/etc/sxuptp/* /etc/sxuptp]
    cmd [mkdir -p /etc/sxnasplus]
    cmd [mkdir -p /tmp/sxnasplus]
    cmd [cp -f /apps/etc/sxnasplus/* /etc/sxnasplus/]
    cmd [ln -sf /sbin/ntfs-3g /sbin/ntfsvlabel]
    cmd [ln -sf /sbin/mtools /sbin/mlabel]
    cmd [ln -sf /sbin/sxhotplugd /sbin/sxhotpluginfo]
    cmd [ln -sf /sbin/sxhotplugd /sbin/sxmount]
    cmd [ln -sf /sbin/sxhotplugd /sbin/sxunmount]
    cmd [cp -f /lib/modules/2.6.31/kernel/drivers/usb/storage/usb-storage.ko /lib/]
    cmd [mkdir -p /etc/minidlna]
    cmd [cp -f /apps/etc/minidlna/* /etc/minidlna/]
    cmd [mkdir -p /tmp/minidlna]
    cmd [mkdir -p /etc/rlwebaccess]
    cmd [cp -f /apps/etc/rlwebaccess/* /etc/rlwebaccess/]
    cmd [chmod 755 /sbin/snihotplug]
    cmd [sysctl -w kernel.hotplug=/sbin/snihotplug]
    kernel.hotplug = /sbin/snihotplug
    cmd [echo OK > /tmp/rl_upnp_result]
    cmd [ln -sf /etc/minidlna/rc.minidlna.sh /tmp/sxnasplus/rc.minidlna.sh]
    cmd [insmod /lib/usb-storage.ko]
    Initializing USB Mass Storage driver...
    usbcore: registered new interface driver usb-storage
    USB Mass Storage support registered.
    cmd [/etc/sxnasplus/rc.sxhotplug.sh start]
    Initialize Hotplug
    Starting HotPlug:                       /sbin/sxhotplugd
    cmd [/etc/sxnasplus/rc.sxnasplus.sh start]
    Initialize SX NAS Plus
    Starting SX NAS Plus FSS Daemon:            /sbin/sxnas-fssd
    Starting SX NAS Plus NS Daemon:             /sbin/sxnas-nsd
    cmd [echo 10626 > /tmp/remotelink_port]
    Initialization has completed
    cmd [date > /var/sysconfd_start_time]
    *We used 24.610000 seconds to initialize all modules*
    cmd [/sbin/processmanager &]
    pSEM_GETID got id 65538
    cmd [/sbin/rmgmt &]
    cmd [/etc/rc.d/rc.local &]
    [RMGMT DBG] RMGMT_VERSION: 3.45.34
    cmd [kill -SIGUSR2 2088]
    *** PROCESS MANAGER Starts ***
    Processmanager update modules
    Reload WAN: ppp0 ...
    Close WAN: ppp0 ...
    -----> LOG : WAN, stop PPPoE mode
    cmd [/sbin/wanmanager -m stop0]
    cmd [/sbin/wanmanager -m stop1]
    cmd [ifconfig eth0.2   0.0.0.0   up]
    Configuring WAN device[WAN0] ...
    cmd [echo 1 > /proc/wancon_type ]
    Connect to ISP using PPPoE ... -----> LOG : WAN, start PPPoE mode
    cmd [chmod 755 /etc/ppp/pap-secrets]
    cmd [chmod 755 /etc/ppp/chap-secrets]
    cmd [chmod 755 /etc/ppp/options.tty0]
    cmd [chmod 0755 /etc/wanconn0.conf]
    cmd [ifconfig eth0.2   0.0.0.0   up]
    cmd [/sbin/wanmanager -m reload0]
    -----> LOG : WAN, No PHY Link
    No PHY Link
    VPN Disconnect ...
    Phy(eth0.2) link disconnected ...Wait for link recover
    Restarting Iptables ....-----> LOG : NET, stop NAT
    -----> LOG : NET, stop Firewall
    Clean iptable...cmd [iptables --flush]
    cmd [iptables -t nat --flush]
    cmd [iptables -t mangle --flush]
    cmd [iptables --policy INPUT   ACCEPT]
    cmd [iptables --policy OUTPUT  ACCEPT]
    cmd [iptables --policy FORWARD ACCEPT]
    OK
    -----> LOG : NET, start NAT
    -----> LOG : NET, start Firewall
    Configuring network routing and filtering ...FCMD[iptables --flush]
    FCMD[iptables -t nat --flush]
    FCMD[iptables -t mangle --flush]
    FCMD[iptables -A INPUT -i lo -j ACCEPT]
    FCMD[iptables -A OUTPUT -o lo -j ACCEPT]
    FCMD[iptables --policy INPUT DROP]
    FCMD[iptables --policy OUTPUT DROP]
    FCMD[iptables --policy FORWARD DROP]
    FCMD[iptables -t nat --policy PREROUTING ACCEPT]
    FCMD[iptables -t nat --policy OUTPUT ACCEPT]
    FCMD[iptables -t nat --policy POSTROUTING ACCEPT]
    FCMD[iptables -t mangle --policy PREROUTING ACCEPT]
    FCMD[iptables -t mangle --policy POSTROUTING ACCEPT]
    FCMD[iptables -t mangle --policy OUTPUT ACCEPT]
    FCMD[iptables --delete-chain]
    FCMD[iptables -t nat --delete-chain]
    FCMD[iptables -t mangle --delete-chain]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags ALL NONE -j DROP]
    FCMD[iptables -A FORWARD -p tcp --tcp-flags ALL NONE -j DROP]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags ALL ALL -j DROP]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags ALL SYN,RST,ACK,FIN,URG -j DROP]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags SYN,FIN SYN,FIN -j DROP]
    FCMD[iptables -A FORWARD -p tcp --tcp-flags SYN,FIN SYN,FIN -j DROP]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags SYN,RST SYN,RST -j DROP]
    FCMD[iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN,RST -j DROP]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags FIN,RST FIN,RST -j DROP]
    FCMD[iptables -A FORWARD -p tcp --tcp-flags FIN,RST FIN,RST -j DROP]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags ACK,FIN FIN -j DROP]
    FCMD[iptables -A FORWARD -p tcp --tcp-flags ACK,FIN FIN -j DROP]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags ACK,PSH PSH -j DROP]
    FCMD[iptables -A FORWARD -p tcp --tcp-flags ACK,PSH PSH -j DROP]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp --tcp-flags ACK,URG URG -j DROP]
    FCMD[iptables -A FORWARD -p tcp --tcp-flags ACK,URG URG -j DROP]
    FCMD[iptables -X synflood]
    FCMD[iptables -N synflood]
    FCMD[iptables -A synflood -p tcp --syn -m limit --limit 20/s --limit-burst 20 -j RETURN]
    FCMD[iptables -A synflood -p tcp -j REJECT --reject-with tcp-reset]
    FCMD[iptables -A INPUT  ! -i br0  -p tcp -m state --state NEW -j synflood]
    FCMD[iptables -t filter -X urlfilter]
    FCMD[iptables -t filter -N urlfilter]
    FCMD[iptables -t nat -A PREROUTING -i br0 -p tcp -d 192.168.0.1 --dport 8080 -j DROP]
    FCMD[iptables -t nat -A PREROUTING -i br0 -p tcp --sport 1024:65535 -d 192.168.0.1 --dport 80 -j DNAT --to-destination 192.168.0.1:8080]
    FCMD[iptables -t nat -A PREROUTING -i br0 -p tcp --sport 1024:65535 ! -d 192.168.0.1 --dport 80 -j DNAT --to-destination 192.168.0.1:10404]
    FCMD[iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT]
    FCMD[iptables -A OUTPUT -m state --state ESTABLISHED,RELATED -j ACCEPT]
    FCMD[iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT]
    FCMD[iptables -A INPUT -s 192.168.0.1 -j DROP]
    FCMD[iptables -A FORWARD -s 192.168.0.1 -j DROP]
    FCMD[iptables -A OUTPUT -o br0 ! -s 192.168.0.1 -j DROP]
    FCMD[iptables -A INPUT -i br0 -p udp --dport 1900 -j ACCEPT]
    FCMD[iptables -A INPUT -i br0 -p tcp --dport 2869 -j ACCEPT]
    FCMD[iptables -A INPUT -i br0 -d 0.0.0.0 -j DROP]
    FCMD[iptables -A INPUT   ! -p udp -d 224.0.0.0/4 -j DROP]
    FCMD[iptables -A FORWARD ! -p udp -d 224.0.0.0/4 -j DROP]
    FCMD[iptables -A INPUT -i br0 -s 239.0.0.0/8 -j ACCEPT]
    FCMD[iptables -A INPUT -i br0 -d 239.0.0.0/8 -j ACCEPT]
    FCMD[iptables -A OUTPUT -o br0 -p udp -s 0.0.0.0 --sport 67 -d 255.255.255.255 --dport 68 -j ACCEPT]
    FCMD[iptables -A INPUT -i br0 -p tcp --dport 53 -j ACCEPT]
    FCMD[iptables -A INPUT -i br0 -p udp --dport 53 -j ACCEPT]
    FCMD[iptables -A OUTPUT -o eth0.2 -p udp --dport 53 -j ACCEPT]
    FCMD[iptables -A OUTPUT -o eth0.2 -p tcp --dport 53 -j ACCEPT]
    FCMD[iptables -A INPUT -i br0 -p udp --dport 69 -j ACCEPT]
    FCMD[iptables -A INPUT -i br0 -p udp -s 192.168.0.0/255.255.255.0 --dport 123 -j ACCEPT]
    FCMD[iptables -A INPUT --fragment -p icmp -j DROP]
    FCMD[iptables -A OUTPUT --fragment -p icmp -j DROP]
    FCMD[iptables -A FORWARD --fragment -p icmp -j DROP]
    FCMD[iptables -A OUTPUT -p icmp --icmp-type source-quench -j ACCEPT]
    FCMD[iptables -A FORWARD -p icmp --icmp-type source-quench -j ACCEPT]
    FCMD[iptables -A INPUT -p icmp --icmp-type parameter-problem -j ACCEPT]
    FCMD[iptables -A OUTPUT -p icmp --icmp-type parameter-problem -j ACCEPT]
    FCMD[iptables -A FORWARD -p icmp --icmp-type parameter-problem -j ACCEPT]
    FCMD[iptables -A INPUT -p icmp --icmp-type destination-unreachable -j ACCEPT]
    FCMD[iptables -A OUTPUT -o br0 -p icmp --icmp-type destination-unreachable -d 192.168.0.1 -j ACCEPT]
    FCMD[iptables -A FORWARD -o br0 -p icmp --icmp-type destination-unreachable -d 192.168.0.1 -j ACCEPT]
    FCMD[iptables -A OUTPUT -p icmp --icmp-type fragmentation-needed -j ACCEPT]
    FCMD[iptables -A FORWARD -p icmp --icmp-type fragmentation-needed -j ACCEPT]
    FCMD[iptables -A OUTPUT -p icmp --icmp-type destination-unreachable -j DROP]
    FCMD[iptables -A INPUT -p icmp --icmp-type time-exceeded -j ACCEPT]
    FCMD[iptables -A FORWARD -o br0 -p icmp --icmp-type time-exceeded -d 192.168.0.1 -j ACCEPT]
    FCMD[iptables -A OUTPUT -p icmp --icmp-type echo-request -m state --state NEW -j ACCEPT]
    FCMD[iptables -X bad-ping]
    FCMD[iptables -N bad-ping]
    FCMD[iptables -A bad-ping -p icmp --icmp-type echo-request -m limit --limit 20/s --limit-burst 20 -j ACCEPT]
    FCMD[iptables -A bad-ping -p icmp --icmp-type echo-request -j DROP]
    FCMD[iptables -A INPUT -i br0 -p icmp --icmp-type echo-request -j bad-ping]
    FCMD[iptables -A OUTPUT -o br0 -s 192.168.0.1 -j ACCEPT]
    FCMD[iptables -A FORWARD -i br0 -o br0 -j ACCEPT]
    FCMD[iptables -A INPUT -i br0 -j ACCEPT]
    FCMD[/sbin/ifconfig eth0.1 up]
    Iptable restart VPN ACL ...VPN ACL ...
    FCMD[echo 1 > /proc/sys/net/ipv4/ip_forward]
    FCMD[echo 0 > /proc/sys/net/ipv4/conf/all/rp_filter]
    FCMD[echo 15 > /proc/sys/net/ipv4/route/gc_interval]
    FCMD[echo 1 > /proc/sys/net/ipv4/ip_dynaddr]
    FCMD[echo 1 > /proc/sys/net/ipv4/conf/eth0.2/arp_filter]
    cmd [sh /var/sysconfd/iptables.sh]
    iptables: No chain/target/match by that name.
    iptables: No chain/target/match by that name.
    iptables: No chain/target/match by that name.
    OK
    OK
    Reloading dnsProxy ...            Stopping DNS Proxy ...            OK
    -----> LOG : DNS, start DNS Proxy
    Set Domain Routing for FLET'S Square Connection...            
    Starting DNS Proxy ...            cmd [/sbin/dnsmasq -C /etc/dnsmasq.conf -i br0 -k &]
    OK
    cmd [kill -SIGUSR1 2088]
    Processmanager update modules
    cmd [ifconfig ath0 down]
    br0: port 2(ath0) entering disabled state
    cmd [iwpriv ath0 mode 11nght40]
    cmd [ifconfig ath1 down]
    br0: port 3(ath1) entering disabled state
    cmd [iwpriv ath1 mode 11nght40]
    cmd [ifconfig ath2 down]
    cmd [iwpriv ath2 mode 11nght40]
    cmd [iwpriv ath0 disablecoext 1]
    
    cmd [iwconfig ath0 channel 0]
    cmd [ifconfig ath0 up]
    Invoking ACS module for Best channel selection 
    br0: port 2(ath0) entering learning state
    cmd [ifconfig ath1 up]
    br0: port 2(ath0) entering forwarding state
    Invoking ACS module for Best channel selection 
    br0: port 3(ath1) entering learning state
    br0: port 3(ath1) entering forwarding state
    cmd [iwconfig ath0 | grep Frequency >/mnt/acsChan]
    -----> LOG : WLAN[2.4G], AutoChannel change to 3
    cmd [ifconfig ath3 down]
    wmi_unified_vdev_stop_send 
    STOPPED EVENT for vap 0 
    br0: port 5(ath3) entering disabled state
    cmd [iwpriv ath3  blockdfschan 1]
    
    cmd [iwconfig ath3 channel 0]OL vap_stop +
    
    wmi_unified_vdev_stop_send 
    OL vap_stop -
    cmd [ifconfig ath3 up]
    OL vap_stop +
    wmi_unified_vdev_stop_send 
    OL vap_stop -
    STOPPED EVENT for vap 0 
    Invoking ACS module for Best channel selection 
    br0: port 5(ath3) entering learning state
    br0: port 5(ath3) entering forwarding state
    STOPPED EVENT for vap 0 
    Function ieee80211_acs_find_best_11na_centerchan best 5G channel is 48
    OL vap_start +
    OL vap_start -
    ol_vdev_start_resp_ev
    ol_ath_vap_join: join operation is only for STA/IBSS mode
    ol_ath_wmm_update:
    Setting vdev param = 3, value = 100
    Notification to UMAC VAP layer
    cmd [iwconfig ath3 | grep Frequency >/mnt/acsChan]
    
広告